EBK MINDTAP FOR HERMAN'S UNDERSTANDING
4th Edition
ISBN: 9781337798761
Author: Herman
Publisher: VST
expand_more
expand_more
format_list_bulleted
Textbook Question
thumb_up100%
Chapter 42, Problem 3RQ
A motor is tripping out on overload. The motor nameplate reveals a full load current of 68 amperes. When the motor is operating under load, an ammeter indicates the following: Phase #1 = 106 amperes, Phase #2 = 104 amperes, and Phase #3 = 105 amperes. What is the most likely problem with this motor?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
What is the peak voltage of a 120V RMS AC voltage?
What is the peak voltage of an AC circuit which has an RMS voltage of 115V?
15. Given the following circuit where IT = 11.65 mA, I1 = 5.63 mA and 13 =2.38 mA, what is 12?
Vs
Answer:
R1
SR2
SR3
I
Chapter 42 Solutions
EBK MINDTAP FOR HERMAN'S UNDERSTANDING
Ch. 42 - What are the three main electrical test...Ch. 42 - What is the advantage of a plunger type voltage...Ch. 42 - A motor is tripping out on overload. The motor...Ch. 42 - A motor is tripping out on overload. The motor...Ch. 42 - Prob. 5RQCh. 42 - Refer to the circuit shown in Figure 42–17. Assume...Ch. 42 - Prob. 7RQCh. 42 - Refer to the circuit shown in Figure 4221. Assume...Ch. 42 - Prob. 9RQCh. 42 - Refer to the circuit shown in Figure 42–21. Assume...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Assume that a nine-lead dual-voltage motor is being tested with an ohmmeter. The meter indicates resistance values as follows: T7–T8 = 6Ω, T7–T9 = 6Ω, and T8–T9 = 10Ω. What would these readings indicate?arrow_forwardA motor nameplate lists the voltage as 208–230/460. The nameplate also lists the full-load amps as 34.2–31.6/15.8. If the motor is operated at 240 volts, what should be the full-load current?arrow_forwardName three factors that determine the amount of induced voltage.arrow_forward
- A motor develops 225 ft-lb of torque at 860 RPM. What is the horsepower output of the motor?arrow_forward1. What will be the output voltage during the positive half cycle of the input voltage? 2. What will be the output voltage during the negative half cycle of the input voltage?arrow_forwardA wye-connected load has a voltage of 480 V applied to it. What is the voltage dropped across each phase?arrow_forward
- What is the minimum pulley diameter for a 1 HP motor running at 1750 RPM?arrow_forwardRefer to the schematic diagram in Figure 318. Assume that the motor is not running. When the third speed push button is pressed, the motor starts in its lowest speed. After a delay of 3 seconds, the motor accelerates to second speed and 3 seconds later to third speed. After a period of about 1 minute, the fourth speed push button is pressed, but the motor does not accelerate to fourth speed. Which of the following could cause this problem? a. Control relay CR2 coil is open. b. S2 contactor coil is open. c. CR3 coil is shorted. d. S3 contactor coil is open.arrow_forwardIn a given DC motor, the output power is 45 HP, and the copper losses are 2.005 KW. If the rotational losses is one tenth of the output power, find the converted power and the efficiency of the motor. Select one: O a. None O b. Pcony = 33.57 KW and % efficiency = 89.2 % %3D O C. Pcony = 39 KW and % efficiency = 75.8 % O d. Peony = 36.927 KW and % efficiency = 86.2 %. !! n dunlay I AP-wound armature whicharrow_forward
- How many lines of magnetic flux must be cut in 1 s to induce a voltage of 1 V?arrow_forwardFor the circuit shown, which of the following is true? OTTE None of these are correct Cylinder 1 Cylinder 2 O Cylinder 2 can't extend in any of the 3 positions of the DCV As cylinder 2 extends, cylinder 1 does not move O As cylinder 2 extends, cylinder 1 retracts O As cylinder 2 extends, cylinder 1 extendsarrow_forwardFor a cylindrical-rotor synchronous machine, the magnitude of the internal generated voltage is |Eg| = 240 volts, and the magnitude of the terminal voltage is |Vt| = 200 volts. Which of the following is true? a. The machine is operating as a generator. O b. The machine is operating as a motor. O C. Information is insufficient to determine the operating mode of this machine.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningElectrical Transformers and Rotating MachinesMechanical EngineeringISBN:9781305494817Author:Stephen L. HermanPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Understanding Motor Controls
Mechanical Engineering
ISBN:9781337798686
Author:Stephen L. Herman
Publisher:Delmar Cengage Learning
Electrical Transformers and Rotating Machines
Mechanical Engineering
ISBN:9781305494817
Author:Stephen L. Herman
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mod-01 Lec-16 Basics of Instrumentation; Author: nptelhrd;https://www.youtube.com/watch?v=qbKnW42ZM5c;License: Standard YouTube License, CC-BY