Connect 1 Semester Access Card For Fluid Mechanics Fundamentals And Applications
3rd Edition
ISBN: 9780077670245
Author: CENGEL
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 5, Problem 1CP
Name four physical quantities that are conserved and two quantities that are not conserved during a process.
Expert Solution & Answer
To determine
The name of four physical quantities that are conserved during a process.
The name of four physical quantities that are not conserved during a process.
Explanation of Solution
The names of four physical quantities that are conserved during a process are given below.
- Mass.
- Linear momentum.
- Angular momentum.
- Energy.
The names of four physical quantities that are not conserved during a process are given below.
- Volume.
- Velocity.
Want to see more full solutions like this?
Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Which of the following statements is true about an incompressible fluid moving through a horizontal pipe?
A. It experiences lower pressure at sections with larger cross-sectional areas.
B. The volume per unit time is smaller at sections with larger cross-sectional areas.
C. The volume per unit time is larger at sections with larger cross-sectional areas.
D. It slows down at sections with larger cross-sectional areas.
In regions far from the entrance, fluid flow through a circular pipe is one dimensional, and the velocity profile for laminar flow is given by u(r) = umax(1 − r2/R2), where R is the radius of the pipe, r is the radial distance from the center of the pipe, and umax is the maximum flow velocity, which occurs at the center. Obtain (a) a relation for the drag force applied by the fluid on a section of the pipe of length L and (b) the value of the drag force for water flow at 20°C with R = 0.08 m, L = 30 m, umax = 3 m/s, and ? =0.0010kg/m⋅s.
Turbines, compressors, boilers, condensers, and heat exchangers operate for long periods of time under the same conditions, and they are classified as __________ flow devices.
Chapter 5 Solutions
Connect 1 Semester Access Card For Fluid Mechanics Fundamentals And Applications
Ch. 5 - Name four physical quantities that are conserved...Ch. 5 - Define mass and volume flow rates. How are they...Ch. 5 - Does the amount of mass entering a control volume...Ch. 5 - When is the flow through a control volume steady?Ch. 5 - Consider a device with one inlet and one outlet....Ch. 5 - In climates with low night-time temperatures, an...Ch. 5 - A garden hose attached with a nozzle is used to...Ch. 5 - Air whose density is 0.082 Ibm/ft3 enters the duct...Ch. 5 - A 0.7$-m3 rigid tank initially contains air whose...Ch. 5 - Consider the flow of an incompressible Newtonian...
Ch. 5 - Consider a fully filled tank of semi-circular...Ch. 5 - Prob. 12PCh. 5 - Prob. 13PCh. 5 - The minimum fresh air requirement of a residential...Ch. 5 - Air enters a nozzle steadily at 2.21 kg/m3 and 20...Ch. 5 - Air at 40°C flow steadily through the pipe shown...Ch. 5 - A hair dryer is basically a duct of constant...Ch. 5 - Define turbine efficiency, generator efficiency,...Ch. 5 - What is mechanical efficiency? What does a...Ch. 5 - How is the combined pump-motor efficiency of a...Ch. 5 - What is mechanical energy? How does it differ from...Ch. 5 - Prob. 22PCh. 5 - A differential thermocouple with sensors at the...Ch. 5 - Electric power is to be generated by installing a...Ch. 5 - Consider a river flowing toward a lake at an...Ch. 5 - Water is pumped from a lake to a storage tank 18 m...Ch. 5 - Prob. 28CPCh. 5 - Express the Bernoulli equation in three different...Ch. 5 - What are the three major assumptions used in the...Ch. 5 - Define static, dynamic, and hydrostatic pressure....Ch. 5 - What is streamwise acceleration? How does it...Ch. 5 - What is stagnation pressure? Explain how it can be...Ch. 5 - Prob. 34CPCh. 5 - How is the location of the hydraulic grade line...Ch. 5 - Prob. 36CPCh. 5 - What is the hydraulic grade line? How does it...Ch. 5 - A glass manometer with oil as the working fluid is...Ch. 5 - The velocity of a fluid flowing in a pipe is to be...Ch. 5 - The water level of a tank on a building roof is 20...Ch. 5 - Prob. 41CPCh. 5 - In a hydroelectric power plant, water enters the...Ch. 5 - A Pitot-static probe is used to measure the speed...Ch. 5 - The air velocity in the duct of a heating system...Ch. 5 - Prob. 45EPCh. 5 - A piezometer and a Pitot tube are tapped into a...Ch. 5 - The diameter of a cylindrical water tank is D0and...Ch. 5 - A siphon pumps water from a large reservoir to a...Ch. 5 - Prob. 49PCh. 5 - Water flows through a horizontal pipe at a rate of...Ch. 5 - An airplane is flying at an altitude of 10.500 m....Ch. 5 - While traveling on a dirt road, the bottom of a...Ch. 5 - The water in an 8-rn-diameter, 3-rn-high...Ch. 5 - Reconsider Prob. 5-49. Determine how long it will...Ch. 5 - Air at 105 kPa and 37°C flows upward through a...Ch. 5 - A handheld bicycle pump can be used as an atomizer...Ch. 5 - Water at 20°C is siphoned from a reservoir as...Ch. 5 - The water pressure in the mains of a city at a...Ch. 5 - A pressurized tank of water has a 10-cm-diameter...Ch. 5 - Air is flowing through a venturi meter whose...Ch. 5 - The water level in a tank is 15 m above the...Ch. 5 - A Pilot-static probe connected to a water...Ch. 5 - The air velocity in a duct is measured by a...Ch. 5 - In cold climates, water pipes may freeze and burst...Ch. 5 - A well-fitting piston with 4 small holes in a...Ch. 5 - A fluid of density and viscosity flows through a...Ch. 5 - What is useful pump head? How is it related to the...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - What is irreversible head loss? How is it related...Ch. 5 - Consider the steady adiabatic flow of an...Ch. 5 - What is the kinetic energy correction factor? Is...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A person is filling a knee-high bucket with water...Ch. 5 - A 3-rn-high tank filled with water has a discharge...Ch. 5 - In a hydroelectric power plant, water flows from...Ch. 5 - Reconsider Prob. 5-78E. Determine the flow rate of...Ch. 5 - An oil pump is drawing 25 kW of electric power...Ch. 5 - Tater is being pumped from a large lake to a...Ch. 5 - A 15-hp (shaft) pump is used to raise water to a...Ch. 5 - Water flows at a rate of 0.035 m3/s in a...Ch. 5 - The water level in a tank is 20 m above the...Ch. 5 - A hydraulic turbine has 50 m of head available at...Ch. 5 - A fan is to be selected to ventilate a bathroom...Ch. 5 - Water flows at a rate of 20 L/s through a...Ch. 5 - The water level in a tank is 34 ft above the...Ch. 5 - A large tank is initially filled with water 5 m...Ch. 5 - Water enters a hydraulic turbine through a...Ch. 5 - The velocity profile for turbulent flow in a...Ch. 5 - Water is pumped from a lower reservoir to a higher...Ch. 5 - Water in a partially filled large tank is to be...Ch. 5 - Underground water is to be pumped by a 78 percent...Ch. 5 - Reconsider Prob. 5-88. Determine the flow rate of...Ch. 5 - A 78-percent efficient 12-hp pump is pumping water...Ch. 5 - The demand for electric power is usually much...Ch. 5 - When a system is subjected to a linear rigid body...Ch. 5 - A fireboat is to fight fires at coastal areas by...Ch. 5 - The velocity of a liquid flowing in a circular...Ch. 5 - Air at 250 kgrn3 enters a nozzle that has an...Ch. 5 - The water level in a tank is 70 ft above the...Ch. 5 - A pressurized 2-rn-diameter tank of water has a...Ch. 5 - Air flows through a pipe at a rate of 120 L/s. The...Ch. 5 - A very large tank contains air at 102 kPa at a...Ch. 5 - Water is flowing through a Venturi meter whose...Ch. 5 - Water flows at a rate of 0.011 m3/s in a...Ch. 5 - The air in a 6-m × 5-m × 4-m hospital room is to...Ch. 5 - Underground water is being pumped into a pool...Ch. 5 - A 3-rn-high large tank is initially filled with...Ch. 5 - Reconsider Prob. 5-105. In order to dram the tank...Ch. 5 - A D0=8 -m-diameter tank is initially filled with...Ch. 5 - In some applications, elbow-type flow meters like...Ch. 5 - The cylindrical water tank with a valve at the...Ch. 5 - A rigid tank of volume 1.5 m3 initially contains...Ch. 5 - A wind tunnel draws atmospheric air at 20°C and...Ch. 5 - Water flows in a 5-cm-diameter pipe at a velocity...Ch. 5 - Air at 100 kPa and 20°C flows in a 12-cm-diameter...Ch. 5 - A water tank initially contains 140 L of water....Ch. 5 - Water enters a 4-cm-diameter pipe at a velocity of...Ch. 5 - The pressure of water is increased from 100 kPa to...Ch. 5 - A 75-m-high water body that is open to the...Ch. 5 - A pump is used to increase the pressure of water...Ch. 5 - A hydraulic turbine is used to generate power by...Ch. 5 - The motor of a pump consumes 1.05 hp of...Ch. 5 - The efficiency of a hydraulic turbine-generator...Ch. 5 - Which parameter is not related in the Bernoulli...Ch. 5 - Consider incompressible, frictionless flow of a...Ch. 5 - Consider incompressible, frictionless flow of...Ch. 5 - Consider water flow in a piping network. The...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The static and stagnation pressures of a fluid in...Ch. 5 - The difference between the heights of energy grade...Ch. 5 - Water at 120 kPa (gage) is flowing in a horizontal...Ch. 5 - Water is withdrawn a the bottom of a large tank...Ch. 5 - Water at 80 kPa (gage) enters a horizontal pipe at...Ch. 5 - Seawater is to be pumped into a large tank at a...Ch. 5 - Water enters a pump at 350 kPa at a rate of 1...Ch. 5 - An adiabatic pump is used to increase the pressure...Ch. 5 - The shaft power from a 90 percent-efficient...Ch. 5 - Using a 1are bucket whose volume is known and...Ch. 5 - Your company is setting up an experiment that...Ch. 5 - Computer-aided designs, the use of better...Ch. 5 - Using a handheld bicycle pump to generate an air...Ch. 5 - Using a flexible drinking straw and a ruler,...Ch. 5 - The power generated by a wind turbine is...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Define the energy equation of a uniformflow system reduces to that of a closed system when all the inlets and exits are closed.arrow_forwardInside of a room, the atmospheric pressure measures out to be 100 kPa. A pipe with a diameter of 0.5 meters is used to release air into the surrounding atmosphere. The fan has a capacity of 2000 m3/h , consumes 1100 watts of power, and rotates at 1000 revolutions per minute. The pressure drop on the suction side is 60 pA, while the pressure drop on the discharge side is 80 kPa. When the operating speed is increased to 1200 revolutions per minute, calculate the fan's capacity based on the resulting change in power. in m3/sarrow_forwardDefine the overall efficiency of a turbine– generator is the product of the efficiency of the turbine and the efficiency of the generator, and it represents the fraction of the mechanical power of the fluid converted to electrical power.arrow_forward
- A cylindrical pipe with a cross-sectional radius r = 1.40[cm] is plunged into a l = 2.30[m] tall open water drum that is initially completely filled with water (pwater = 1000 [kg/m3]). The pipe goes h1 = 0.35 [m] above the drum before dropping down h2 = 3.50 [m] below the base of the drum as shown. The cross-sectional radius of the top side of the pipe is R = 2.20 [cm].A. How fast is the water going out of this pipe?B. What's the liquid's pressure at the top of the pipe? Assume that the system is exposed to 1.00 [atm] of air pressure.C. What's the maximum height the pipe can go above the drum before the water stops flowing out of the pipe? For liquid flow to be continuous, the liquid’s pressure must not fall before its vapor pressure. Assume that vapor pressure, in this case, is 2.30 [kPa].arrow_forwardAn 80-percent-efficient pump with a power input of 20 hp is pumping water from a lake to a nearby pool at a rate of 1.5 ft3 /s through a constant-diameter pipe. The free surface of the pool is 80 ft above that of the lake. Determine the mechanical power used to overcome frictional effects in piping.arrow_forwardA U-shaped tube is filled with water of density 1000 kg/m3 until the level of the liquid is 28 cm above the bottom of the tube. Then oil of specific gravity 0.78 is poured into one branch of the tube until the level of the liquid in the other branch is 34 cm above the bottom of the tube. (g=9.8m/s2) I) Find the level of the oil-water interface in the branch where the oil was spilled II) Find the level of the oil-air interface in the branch where the oil was spilledarrow_forward
- DESCRIBE THE ENERGY ANALYSIS OF STEADY-FLOW SYSTEMSarrow_forwardA tank contains water that is being drained by a pipe at a constant rate. The pipe has a diameter of 0.1 m and is 5 m long. The water flows out of the pipe and into a river with a velocity of 2 m/s. The water level in the tank is decreasing at a constant rate of 0.5 cm/s. Determine the velocity of the water in the pipe.arrow_forwardDescribe how the Internal Energy (U) change with respect to pressure-volume workarrow_forward
- A cylindrical 125 cm high and 89 cm diameter, as given by the figurethe inside of the tank is initially completely filled with oil. Then 1.25 to the base edge of the tanka hole in diameter of cm is opened and the oil begins to drain from this hole. Oil output speed from tank(2gh)-1/2is given as. (h, the variable height of the oil inside the tank from the center of the holeand G indicates the acceleration of gravity). From the base of the oil level inside the tankCalculate the time it takes to fall to a height of 15 cm in [s].arrow_forwardThe water level in a tank is 70 ft above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank is at sea level, and the water surface is open to the atmosphere. In the line leading from the tank to the nozzle is a pump, which increases the water pressure by 15 psia. Determine the maximum height to which the water stream could rise.arrow_forwardThe water level required in a tank to obtain velocity of 10 m/s at bottom isarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Introduction To Engg Mechanics - Newton's Laws of motion - Kinetics - Kinematics; Author: EzEd Channel;https://www.youtube.com/watch?v=ksmsp9OzAsI;License: Standard YouTube License, CC-BY