EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
4th Edition
ISBN: 8220102719569
Author: ZANIEWSKI
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 5, Problem 5.17QP
The specific gravity and absorption test (ASTM C128) was performed on fine aggregate and the following data were obtained:
Mass of SSD sand = 500.0 g
Mass of pycnometer with water only = 623.0 g
Mass of pycnometer with sand and water = 938.2 g
Mass of dry sand = 495.5 g
Calculate the specific gravity values (dry bulk, SSD, and apparent) and the absorption of the fine aggregate.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
formed?
Q1: B: The specific gravity and absorption test was performed on fine aggregate and the
following data were obtained:
Mass of SSD sand = 500.0 g
Mass of pycnometer with water only = 623.0 g
Mass of pycnometer with sand and water= 938.2 g
Mass of dry sand = 495.5 g
Calculate the specific gravity values (dry bulk, SSD, and apparent) and the absorption of
the fine aggregate.
Three samples of fine aggregate have the properties shown below. Determine in percentage:
(a) total moisture content and (b) free moisture content for each sample and the average of
the three samples.
Table P5.7
Measure
Wet Mass (g)
Dry Mass (g)
Absorption (%)
Sample
A
521.0
491.6
2.5
B
522.4
491.7
2.4
C
523.4
492.1
2.3
Three samples of fine aggregate have the properties shown in Table P5.9.
TABLE P5.9
Sample
Measure
A
B
Wet Mass (g)
521.0
522.4
523.4
Dry Mass (g)
491.6
491.7
492.1
Absorption (%)
2.5
2.4
2.3
Determine in percentage: (a) total moisture content and (b) free moisture
content for each sample and the average of the three samples.
Chapter 5 Solutions
EBK MATERIALS FOR CIVIL AND CONSTRUCTIO
Ch. 5 - Prob. 5.1QPCh. 5 - Discuss five different desirable characteristics...Ch. 5 - Discuss five different desirable characteristics...Ch. 5 - The shape and surface texture of aggregate...Ch. 5 - Define the following terms: a. Saturated...Ch. 5 - Three samples of fine aggregate have the...Ch. 5 - A sample of wet aggregate weighed 297.2 N. After...Ch. 5 - 46.5 kg (102.3 lb) of fine aggregate is mixed with...Ch. 5 - Samples of coarse aggregate from a stockpile are...Ch. 5 - Base course aggregate has a target dry density of...
Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Calculate the percent voids between aggregate...Ch. 5 - Coarse aggregate is placed in a rigid bucket and...Ch. 5 - The following laboratory tests are performed on...Ch. 5 - Students in the materials lab performed the...Ch. 5 - The specific gravity and absorption test (ASTM...Ch. 5 - Prob. 5.18QPCh. 5 - Calculate the sieve analysis shown in Table P5.19...Ch. 5 - Calculate the sieve analysis shown in Table P5.20,...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - A sieve analysis test was performed on a sample of...Ch. 5 - Draw a graph to show the cumulative percent...Ch. 5 - Referring to Table 5.6, plot the specification...Ch. 5 - Referring to the aggregate gradations A, B, and C...Ch. 5 - Table P5.26 shows the grain size distributions of...Ch. 5 - Table P5.27 shows the grain size distributions of...Ch. 5 - Three aggregates are to be mixed together in the...Ch. 5 - Table P5.29 shows the grain size distribution for...Ch. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Table P5.31 shows the grain size distribution for...Ch. 5 - Prob. 5.32QPCh. 5 - Laboratory specific gravity and absorption tests...Ch. 5 - Prob. 5.34QPCh. 5 - Define the fineness modulus of aggregate. What is...Ch. 5 - Calculate the fineness modulus of aggregate A in...Ch. 5 - Calculate the fineness modulus of aggregate B in...Ch. 5 - A portland cement concrete mix requires mixing...Ch. 5 - Discuss the effect of the amount of material...Ch. 5 - Aggregates from three sources having the...Ch. 5 - Aggregates from three sources having the...Ch. 5 - A contractor is considering using three stockpiles...Ch. 5 - Prob. 5.43QPCh. 5 - What are the typical deleterious substances in...Ch. 5 - Review ASTM D75 and summarize the following: a....
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
11-1. Determine the moments at A,B, and C, then draw
the moment diagram for the beam. The moment of ine...
Structural Analysis (10th Edition)
What production method for steel shapes is specified by the following organizations? AISI (American Iron and St...
Structural Steel Design (6th Edition)
1.2 Explain the difference between geodetic and plane
surveys,
Elementary Surveying (14th Edition)
A 3 ft square footing carries a sustained load of 10 k. It is placed on the surface of a 30 ft thick saturated ...
Foundation Design: Principles and Practices (3rd Edition)
5.11 What error results on a 200-ft sight with a level if the rod reading is 6.307 ft but the top of the
7-ft r...
Elementary Surveying: An Introduction To Geomatics (15th Edition)
Select a mechanical component from Part 3 of this book (roller bearings, springs, etc.), go to the Internet, an...
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) absorption, in percentb) free moisture if the sand in the stockpile has a moisture content of 3% bbbbbbbbbbbbbbarrow_forwardThe specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 400.0 gMass of pycnometer with water = 520.0 gMass of pycnometer with water plus sand = 850.0 gMass of dry sand = 397.0 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravity aaaaaaaaaaarrow_forwardThe specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 450.0 gMass of pycnometer with water = 550 gMass of pycnometer with water plus sand = 840 gMass of dry sand = 446.5 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravityd) absorption, in percente) free moisture if the sand in the stockpile has a moisture content of 5%.arrow_forward
- A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results below. Determine the following: a. Percent passing through each sieve (Tabulation) b. Plot of the percent finer in the Semi-Log Gradation Chart c. Maximum Aggregate Size of the Sample (mm) d. Nominal Maximum Aggregate size of the sample e. Fineness Modulusarrow_forwardQuestion 2 Calculate the moisture content and absorption capacity for the following three aggregate samples. Report the moisture state of each aggregate. a) An aggregate sample from a stockpile A has a mass of 19.00 lb. When oven-dried, it has a mass of 17.98 lb. When brought to a saturated surface dry state it has a mass of 19.00 lb. b) An aggregate sample from a stockpile B has a mass of 5.08 kg. When oven-dried, it has a mass of 5.01 kg. When brought to a saturated surface dry state it has a mass of 5.13 kg. c) An aggregate sample from a stockpile C has a mass of 53.98 lb. When oven-dried, it has a mass of 53.22 lb. When brought to a saturated surface dry state it has a mass of 53.54 Ib.arrow_forward7 The specific gravity and absorption test (ASTM C128) was performed on fine aggregate and the following data were obtained:Mass of SSD sand = 500.0 gMass of pycnometer with water only = 623.0 gMass of pycnometer with sand and water = 938.2 gMass of dry sand = 495.5 gCalculate the specific gravity values (dry bulk, SSD, and apparent) and theabsorption of the fine aggregatearrow_forward
- TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ± 5°C, then cool to room temperature. 2. Select suitable sieve sizes to furnish the information required by the specifications covering the material to be tested. Common sieves in millimeters are 37.5, 25, 19, 12.5, 9.5, 4.75, 2.36, 1.18, 0.6, 0.3, 0.15, and 0.075 mm (11 2 in., 1 in., 3 4 in., 1 2 in., 3 8 in., No. 4, No. 8, No. 16, No. 30, No. 50, No. 100, and No. 200). 3. Nest the sieves in order of decreasing size of opening, and place the aggregate sample on the top sieve. 4. Agitate the sieves by hand or by mechanical apparatus for a sufficient period. The criterion for sieving time is that, after completion, not more than 1% of the residue on any individual sieve will pass that sieve during 1 minute of continuous hand sieving. 5. Determine the weight of each size increment. 6. The total weight of the material after sieving should be compared with the original weight of the sample placed…arrow_forwardSpecific Gravity and absorption test is done in the materials lab on a sample of coarse aggregate and the following data is obtained: Dry weight: 1002.3 g SSD weight: 1032.4 g Submerged weight: 607.5 g Calculate the specific gravity values (dry, SSD and apparent) and the absorption of the coarse aggregate.arrow_forwardI 1. Determine the apparent specific gravity (G.), dry bulk specific gravity (Gs(OD)), SSD bulk specific gravity (Gt(ssD) and absorption capacity of a fine aggregate sample using the following data: Weight of sample in dry condition: 485 g • Weight of sample in SSD condition: 505 g • Weight of pycnometer with the sample and water: 1015 g Weight of pycnometer with water: 700 garrow_forward
- 5) Determine the apparent specifie gravity (G.), dry bulk specific gravity (Guon), SSD bulk specific gravity (Ghessn) and absorption capacity of a fine aggregate sample using the folowing data: • Weight of sample in dry condition: 485 g Weight of sample in SSD condition: 505 g • Weight of pyenometer with the sample and water: 1015 g • Weight of pycnometer with water: 700 garrow_forwardExample 2: Specific gravity test was conducted for a fine aggregate. If the following data was obtained during the test: - the saturated surface dry weight of the sample = 500 g. %3D - Weight of pycnometer full of water= 750 g - Weight of pycnometer and sample and water= 1050 g. - Oven dry weight of the sample is 475 g. for this aggregate, FIND - The apparent specific gravity. - The bulk specific gravity on an ssd basis. Percentage of absorption.arrow_forwardFine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.42, Apparent specific gravity= 2.58, mass of the vessel full of water = 1350 gm, mass of the vessel plus sand and topped up with water= 1600 gm, mass in wet condition 541 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent densityarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
Aggregates: Properties; Author: nptelhrd;https://www.youtube.com/watch?v=49yGZYeokKM;License: Standard YouTube License, CC-BY