EBK FLUID MECHANICS: FUNDAMENTALS AND A
4th Edition
ISBN: 8220103676205
Author: CENGEL
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 6, Problem 108P
The ve1ocity of wind at a wind turbine is measured to be 8 m/s. The blade span diameter is 12 in. The density of air is I .2 kg m3. If the horizontal force exerted by the wind on the supporting mast of the wind turbine is 1620 N. the efficiency of the wind turbine is
(a) 27.5%
(b) 31.7%
(c) 29.5%
(d) 3.1%
(e)33.8%
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
3.) An air compressor handles 8.5 m’/min of with a density of 1.26 kg/m³ and a pressure of 1
atm, and it discharges at 445 kPa (gage) with a density of 4.86 kg/m³. The change in
specific internal energy across the compressor is 82 kJ/kg, and the heat loss by cooling is 24
kJ/kg. Neglecting changes in kinetic and potential energies, find (a) the work in kJ/kg and
(b) the power in kW.
How long should a rotor blade of a wind turbine be if it is designed to produce 10 kW and the prevailing wind speed is about 50 kph? Assume that air density is 1.20 kg/m3.
A water jet has a diameter of 75mm and ahs a velocity of 15m/s. What is the horsepower exerted by the jet. ANSWER: 10hp
Chapter 6 Solutions
EBK FLUID MECHANICS: FUNDAMENTALS AND A
Ch. 6 - Express Newton’s second law of motion for rotating...Ch. 6 - Express Newton’s first, second, and third laws.Ch. 6 - Is momentum a vector? If so, in what direction...Ch. 6 - Express the conservation of momentum principle....Ch. 6 - How do surface forces arise in the momentum...Ch. 6 - Explain the importance of the Reynolds transport...Ch. 6 - What is the importance of the momentum-flux...Ch. 6 - Write the momentum equation for steady...Ch. 6 - In the application of the momentum equation,...Ch. 6 - Two firefighters are fighting a fire with...
Ch. 6 - A rocket in space (no friction or resistance to...Ch. 6 - Describe in terms of momentum and airflow how a...Ch. 6 - Does it take more, equal, or less power for a...Ch. 6 - In a given location, would a helicopter require...Ch. 6 - Describe body forces and surface forces, and...Ch. 6 - A constant-velocity horizontal water jet from a...Ch. 6 - A horizontal water jet of constant velocity V from...Ch. 6 - A horizontal water jet from a nozzle of constant...Ch. 6 - A 2.5-cm-diameter horizontal water jet with a...Ch. 6 - A 90 elbow in a horizontal pipe is used to direct...Ch. 6 - Repeat Prob. 6-20 for the case of another...Ch. 6 - A horizontal water jet impinges against a vertical...Ch. 6 - Water enters a 7-cm-diameter pipe steadily with a...Ch. 6 - A reducing elbow in a horizontal pipe is used to...Ch. 6 - Repeat Prob. 6-24 for the case of = 125°.Ch. 6 - A 100-ft3/s water jet is moving in the positive...Ch. 6 - Reconsider Prob. 6-26E. Using appropriate...Ch. 6 - Commercially available large wind turbines have...Ch. 6 - A fan with 24-in-diameter blades moves 2000 cfm...Ch. 6 - A 3-in-diameter horizontal jet of water, with...Ch. 6 - Firefighters are holding a nozzle at the end of a...Ch. 6 - A 5-cm-diameter horizontal jet of water with a...Ch. 6 - Prob. 33PCh. 6 - A 3-in-diameter horizontal water jet having a...Ch. 6 - An unloaded helicopter of mass 12,000 kg hovers at...Ch. 6 - Prob. 36PCh. 6 - Water is flowing through a 10-cm-diameter water...Ch. 6 - Water flowing in a horizontal 25-cm-diameter pipe...Ch. 6 - Prob. 39PCh. 6 - Water enters a centrifugal pump axially at...Ch. 6 - An incompressible fluid of density and viscosity ...Ch. 6 - Consider the curved duct of Prob. 6-41, except...Ch. 6 - As a follow-up to Prob. 6-41, it turns out that...Ch. 6 - Prob. 44PCh. 6 - The weight of a water tank open to the atmosphere...Ch. 6 - A sluice gate, which controls flow rate in a...Ch. 6 - A room is to be ventilated using a centrifugal...Ch. 6 - How is the angular momentum equation obtained from...Ch. 6 - Prob. 49CPCh. 6 - Prob. 50CPCh. 6 - Prob. 51CPCh. 6 - A large lawn sprinkler with two identical arms is...Ch. 6 - Prob. 53EPCh. 6 - The impeller of a centrifugal pump has inner and...Ch. 6 - Water is flowing through a 15-cm-diameter pipe...Ch. 6 - Prob. 56PCh. 6 - Repeat Prob. 6-56 for a water flow rate of 60 L/s.Ch. 6 - Prob. 58PCh. 6 - Water enters the impeller of a centrifugal pump...Ch. 6 - A lawn sprinkler with three identical antis is...Ch. 6 - Prob. 62PCh. 6 - The impeller of a centrifugal blower has a radius...Ch. 6 - An 8-cm-diameter horizontal water jet having a...Ch. 6 - Water flowing steadily at a rate of 0.16 m3/s is...Ch. 6 - Repeat Prob. 6-66 by taking into consideration the...Ch. 6 - A 16-cm diameter horizontal water jet with a speed...Ch. 6 - Water enters vertically and steadily at a rate of...Ch. 6 - Repeal Prob. 6-69 for the case of unequal anus-the...Ch. 6 - Prob. 71PCh. 6 - Prob. 72PCh. 6 - A spacecraft cruising in space at a constant...Ch. 6 - A 60-kg ice skater is standing on ice with ice...Ch. 6 - A 5-cm-diameter horizontal jet of water, with...Ch. 6 - Water is flowing into and discharging from a pipe...Ch. 6 - Indiana Jones needs So ascend a 10-m-high...Ch. 6 - Prob. 79EPCh. 6 - A walnut with a mass of 50 g requires a force of...Ch. 6 - Prob. 81PCh. 6 - Prob. 82PCh. 6 - A horizontal water jet of constant velocity V...Ch. 6 - Show that the force exerted by a liquid jet on a...Ch. 6 - Prob. 85PCh. 6 - Prob. 86PCh. 6 - Water enters a mixed flow pump axially at a rate...Ch. 6 - Prob. 88PCh. 6 - Water enters a two-armed lawn sprinkler along the...Ch. 6 - Prob. 91PCh. 6 - Prob. 92PCh. 6 - Prob. 93PCh. 6 - Prob. 94PCh. 6 - A water jet strikes a moving plate at velocity...Ch. 6 - Water flows at mass flow rate m through a 90°...Ch. 6 - Prob. 97PCh. 6 - Water shoots out of a Iar2e tank sitting a cart...Ch. 6 - Prob. 99PCh. 6 - Prob. 100PCh. 6 - Prob. 101PCh. 6 - Consider water flow through a horizontal, short...Ch. 6 - Consider water flow through a horizontal. short...Ch. 6 - Prob. 104PCh. 6 - Prob. 105PCh. 6 - Prob. 106PCh. 6 - The velocity of wind at a wind turbine is measured...Ch. 6 - The ve1ocity of wind at a wind turbine is measured...Ch. 6 - Prob. 109PCh. 6 - Prob. 110PCh. 6 - Prob. 111PCh. 6 - Consider the impeller of a centrifugal pump with a...Ch. 6 - Prob. 113PCh. 6 - Prob. 114P
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In wind turbines, the minimum wind speed at which useful power can be generated is called the (a) Rated speed (b) Cut-in speed (c) Cut-out speed (d) Available speed (e) Betz speedarrow_forwardA centrifugal pump is required to handle 50 lit/sec of gasoline against a net pressure of 4 kg/cm², Determine the head in m of liquid and the HP required by the pump, if its overall efficiency is 62%. Take the specific gravity of gasoline as 0.7. (57 and 43) A centrifugal pump draws water from a sump through a vertical 15 cm pipe. The pump has a horizontal discharge pipe 10 cm diameter which is 3.5 m above water level in the sump. While pumping 35 lit/sec, gauges near the pump at entrance and discharge read kg/cm respectively. The discharge gauge is 0.5 m above the suction gauge. Determine the horsepower output of the pump. 0.35 kg/cm and+1.8 (10.82) - To p. edict the performance of a loge centrifugal pump, its model, having р. the following specification, was made: P=24 IIP H=8 m N=925 rpm Diameter of model pump impeller is 9 times smaller than that of the prototype. The prototype pump has to work against a head of 30 m. Find its working speed and HP required to drive it. Determine…arrow_forwardProblem (2) Neglecting friction, find the horizontal force of the water (N) on the horizontal bend shown in the figure. V, = 10 m/s %3D 8 cm dia. V2 4 cm Answer:arrow_forward
- A boat moved by jet propulsion discharges water through a jet of area 0.02 m2; the water being drawn from inlet opening facing the direction of motion. The total drag is estimated to be 17.66 u2 N·m where u is the speed of the boat in metre per second. Take density of water at 1,020 kg/m3 and efficiency of the pump set is 78%. If the boat moves at 54 kilometers per hour, determine the following: A) Relative velocity of the jet in meters per second B) The power, in kilowatts, of the motor required to work the pumps C) Efficiency of propulsion, in %arrow_forward2. At a certain location, wind is blowing steadily at 10 m/s. Determine the mechanical energy of air per unit mass and the power generation potential of a wind turbine with 60-m-diameter blades at that location. Take the air density to be 1.25 kg/m3. ất Region XI can utilize aside from hydroelectric power? 3. In your perspective, what are top three energy so Support your answer. ich the windarrow_forwardFind the maximum power developed by the turbine. Data H1= 37 m, H4= 2 1 m, D2=56 cm, D4= 35 cm, V4= 8.5 m/s, P4= 200 kPa, Patm= 100 kPa, 1000 kg/m3. * Lake H, P.O V. h D2 H. Turbine Your answerarrow_forward
- Maximizing the wind velocity of 92 m/s and 25 units of wind turbine was installed at the seaside shore. What is the total power if the area of turbine blade equal to 42 sq.m. with air density of 1.2041 Kg/cu.m. A 1.969 MW 1,968,998 Watts 4,923 watts D 49.23 MWarrow_forwardA gasoline pump fills a 80-L tank in 1 min 30 s. If the pump exit diameter is 4cm, what is the average pump-flow velocity?arrow_forwardTwo electric motors are being considered to drive a centrifugal pump. Each motor is capable of delivering 60 horsepower (output) to the pumping operation. It is expected that the motors will be in use 2,000 hours per year and the MARR = 8% per year. (1 hp = 0.746 kW) a. If electricity costs $X per kilowatt-hour, calculate the annual cost of electrical power for each motor b. What cost of electricity (S/kWh) makes the two pumps breakeven (i.e. have the same equivalent annual cost)? Assume repeatability and MVS = $0. c. Choose the graph to illustrate your answer to Part (b). d. Which motor should be selected? Click the icon to view the datatable for the additional information about two alternatives. Click the icon to view the interest and annuity table for discrete compounding when the MARR is 8% per year. a. The annual cost of electrical power for Motor A is $(xX). (Round to two decimal places.)arrow_forward
- Show the solution The motor power needed to drive the fan is 75 kW and the volume flow of air delivered by fan is 23 m³/s and 20 cm water gage. The density of air is 1.2 kg/m³ . What is the fan efficiency?arrow_forward(4) A water hose connected to a nozzle is used to fill a 10 L container. The internal diameter of the hose is 2 cm and the nozzle exit has an inner diameter of 1.7 cm. It takes 30 s to fill up the container. If the inlet pressure is 2 atm and the nozzle exit is 0.8 m above the hosea. What is the velocity (m/s) of water at the outlet stream and at the inlet stream?b. What is the water pressure (atm) at the outlet stream c. What is the mass flow rate of water (kg/s)?arrow_forwardTwo electric motors are being considered to drive a centrifugal pump. Each motor is capable of delivering 90 horsepower (output) to the pumping operation. It is expected that the motors will be in use 2,000 hours per year and the MARR = 5% per year. (1 hp = 0.746 kW) a. If electricity costs $X per kilowatt-hour, calculate the annual cost of electrical power for each motor b. What cost of electricity ($/kWh) makes the two pumps breakeven (i.e. have the same equivalent annual cost)? Assume repeatability and MVs = $0. c. Choose the graph to illustrate your answer to Part (b). d. Which motor should be selected? Click the icon to view the datatable for the additional information about two alternatives. Click the icon to view the interest and annuity table for discrete compounding when the MARR is 5% per year. a. The annual cost of electrical power for Motor A is $( XX). (Round to two decimal places.)arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Fluid Mechanics - Viscosity and Shear Strain Rate in 9 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=_0aaRDAdPTY;License: Standard youtube license