Materials For Civil And Construction Engineers In Si Units
4th Edition
ISBN: 9781292154404
Author: Michael S Mamlouk
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 6, Problem 6.24QP
Four standard mortar cubes were made using nonpotable water available at the job site, and four others were made using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the failure loads in kilograms shown in Table P6.24. Also, the Vicat test was conducted on the cement paste made with the questionable water and showed that the set time is 1_2 hour less than the set time of paste made with potable water. Based on these results, would you accept that water for mixing concrete according to ASTM standards? Explain why.
TABLE P6.24
| Nonpotable Water | Potable Water |
| 6909 | 7773 |
| 6591 | 7400 |
| 6302 | 7599 |
| 7227 | 7364 |
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Three standard mortar cubes were made using nonpotable water available at the job site, and three others were made using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the failure loads in kN shown in Table P6.22. The Vicat test was conducted on the cement paste made with the questionable water and showed that the set time was 45 minutes more than the set time of paste made with potable water. Based on these results, would you accept that water for mixing concrete according to ASTM standards? Explain why.
Three standard mortar cubes were made using nonpotable water available atthe job site, and three others were made using potable water. The cubes weretested for compressive strength after 7 days of curing and produced the failureloads in kips shown in Table P6.23.The Vicat test was conducted on the cement paste made with the questionablewater and showed that the set time was 45 minutes more than the set time ofpaste made with potable water. Based on these results, would you accept thatwater for mixing concrete according to ASTM standards? Explain why.
Four standard mortar cubes were made using nonpotable water available atthe job site, and four others were made using potable water. The cubes weretested for compressive strength after 7 days of curing and produced the failureloads in kilograms shown in Table P6.24.Also, the Vicat test was conducted on the cement paste made with the ques-tionable water and showed that the set time is 0.5hour less than the set timeof paste made with potable water. Based on these results, would you acceptthat water for mixing concrete according to ASTM standards? Explain why.
Chapter 6 Solutions
Materials For Civil And Construction Engineers In Si Units
Ch. 6 - What ingredients are used for the production of...Ch. 6 - What is the role of gypsum in the production of...Ch. 6 - What is a typical value for the fineness of...Ch. 6 - What are the primary chemical reactions during the...Ch. 6 - Define the C-S-H phase of cement paste.Ch. 6 - What are the four main chemical compounds in...Ch. 6 - Prob. 6.7QPCh. 6 - Define a. interlayer hydration space b. capillary...Ch. 6 - Prob. 6.9QPCh. 6 - The following laboratory tests are performed: a....
Ch. 6 - What is a false set of portland cement? State one...Ch. 6 - The watercement ratio is important because it...Ch. 6 - Discuss the effect of watercement ratio on the...Ch. 6 - Draw a graph to show the general relationship...Ch. 6 - Students in the materials class prepared three...Ch. 6 - Students in the materials class prepared three...Ch. 6 - Two batches of cement mortar with properties as...Ch. 6 - What are the five primary types and functions of...Ch. 6 - Why isnt pozzolan used with Type III cement?Ch. 6 - What type of cement would you use in each of the...Ch. 6 - In order to evaluate the suitability of nonpotable...Ch. 6 - Three standard mortar cubes were made using...Ch. 6 - Four standard mortar cubes were made using...Ch. 6 - Discuss the problem of disposal of waste water...Ch. 6 - State five types of admixtures and discuss their...Ch. 6 - Prob. 6.27QPCh. 6 - Under what condition is an air-entraining agent...Ch. 6 - If a water reducer is added to the concrete mix...Ch. 6 - Prob. 6.30QPCh. 6 - A concrete mix includes the following ingredients...Ch. 6 - The results of an experiment to evaluate the...Ch. 6 - The results of a laboratory experiment to evaluate...Ch. 6 - Referring to Table P6.34, Mix No. 1 was designed...Ch. 6 - Two batches of concrete cylinders were made with...Ch. 6 - Two batches of concrete cylinders were made with...Ch. 6 - What is the source of fly ash? Why is fly ash...Ch. 6 - A materials engineer is working in a research...Ch. 6 - A materials engineer is working in a research...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What production method for steel shapes is specified by the following organizations? AISI (American Iron and St...
Structural Steel Design (6th Edition)
A 3 ft square footing carries a sustained load of 10 k. It is placed on the surface of a 30 ft thick saturated ...
Foundation Design: Principles and Practices (3rd Edition)
5.11 What error results on a 200-ft sight with a level if the rod reading is 6.307 ft but the top of the
7-ft r...
Elementary Surveying: An Introduction To Geomatics (15th Edition)
11-1. Determine the moments at A,B, and C, then draw
the moment diagram for the beam. The moment of ine...
Structural Analysis (10th Edition)
1.2 Explain the difference between geodetic and plane
surveys,
Elementary Surveying (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- 2. Data for calculating compressive strength: Ø Tested material – cement paste Ø Force destroying the specimen (first half of the beam), Fc1 – 25900 N Ø Force destroying the specimen (first half of the beam), Fc2 – 26300 N Calculate compressive strengtharrow_forwardThe results of an experiment to evaluate the effects of a water reducer areshown in Table P6.32.a. Calculate the water–cement ratio in each of the three cases.b. Using water reducer, how can we increase the compressive strength ofconcrete without changing workability? Refer to the appropriate case inthe table.c. Using water reducer, how can we improve workability without changingthe compressive strength? Refer to the appropriate case in the table.d. Using water reducer, how can we reduce cost without changingworkability or strength? (Assume that the cost of the small amountof water reducer added is less than the cost of cement.) Refer to theappropriate case in the table.e. Summarize all possible effects of water reducers on concrete.arrow_forwardA materials engineer is working in a research project to evaluate the effect of one type of admixture on the compressive strength of concrete. He tested eight mortar cubes made with admixture and eight others without admixture after 28 days of curing. The compressive strengths of cubes in MPa with and without admixture are shown in Table P6.38. Using the statistical t-test, is there a significant difference between the means of the compressive strengths of the two cement mortars at a level of signifi- cance of 0.10?arrow_forward
- Three standard mortar cubes were made using nonpotable water available at the job site, and three others were made using potable water. The cubes were tested for compressive strength after seven days of curing and produced the following failure loads in kilograms:Based on these results only, would you accept that water for mixing concrete according to ASTM standards? Why?arrow_forwardA materials engineer is working in a research project to evaluate the effect of one type of admixture on the compressive strength of concrete. He tested eight mortar cubes made with admixture and eight others without admixture after 28 days of curing. The compressive strengths of cubes in psi with and without admixture are shown in Table P6.40.Using the statistical t-test, is there a significant difference between the meansof the compressive strengths of the two cement mortars at a level of signifi-cance of 0.10?arrow_forwardThree 150 mm * 300 mm concrete cylinders with water to cement ratios of0.4, 0.6, and 0.8, respectively. After curing for 28 days, the specimens weresubjected to increments of compressive loads until failure. The load versusdeformation results were as shown in Table P7.26. Assuming that the gauge length is the whole specimen height, it is required todo the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for all specimens on one graph.c. The ultimate strength for each specimen.d. The modulus of elasticity as the secant modulus at 40% of the ultimatestress for each specimen.e. The strain at failure for each specimen.f. The toughness for each specimen.g. Comment on the effect of increasing the water–cement ratio on thefollowing:i. Ultimate strengthii. Modulus of elasticityiii. Ductilityiv. Toughness. Curves may be approximated with a series of straight lines.arrow_forward
- Two batches of cement mortar with properties as shown in Table P6.18. Ifmortar cubes are made from these batches, which batch do you expect to havelarger compressive strength? Why?arrow_forwardThree 150 mm * 300 mm concrete cylinders with water to cement ratios of 0.4, 0.6, and 0.8, respectively. After curing for 28 days, the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table .Assuming that the gauge length is the whole specimen height, it is required to do the following:a. The compressive stresses and strains for each specimen at each load increment.b. Plot stresses versus strains for all specimens on one graph.c. The ultimate strength for each specimen.d. The modulus of elasticity as the secant modulus at 40% of the ultimate stress for each specimen. e. The strain at failure for each specimen.f. The toughness for each specimen. g. Comment on the effect of increasing the water–cement ratio on the following:i. Ultimate strengthii. Modulus of elasticityiii. Ductilityiv. Toughness. Curves may be approximated with a series of straight lines.arrow_forwardUsing Figure 7.34,a. Determine the ultimate stress at each water–cement ratio.b. Determine the secant modulus at 40% of the ultimate stress at eachwater–cement ratio.c. Plot the relationship between the secant moduli and the ultimate stresses.d. Plot the relationship between the moduli and the ultimate stresses onthe same graph of part (c), using the relation of the ACI Building Code(Equation 7.3).e. Compare the two relations in questions c and d and comment on anydiscrepancies.f. Determine the toughness at each water–cement ratio and comment on theeffect of increasing water–cement ratio on the toughness of concrete.arrow_forward
- 150 mm * 300 mm concrete cylinders were made of the same batch and sepa- rated at random to six equal groups. The six groups of cylinders were sub- merged in water for different times before testing for compressive strength and the results are shown in Table P7.39. It is required to do the following: a. Determine the compressive strength at different curing times. b. Using an Excel sheet, plot the relationship between curing time and compressive strength. Label all axes and curves. c. Comment on the effect of curing time on the compressive strength. d. What is the approximate ratio between the compressive strengths at 7 days and 28 days? e. What is the approximate ratio between the compressive strengths at 28 days and 180 days?arrow_forwarda. When is it necessary to consolidate concrete by vibration in test method C231? Discuss the process of vibration when placing and consolidating the sample.b. When rodding a layer of concrete in method C138, is it okay to hit the bottom of the measure? If not, how is it supposed to be done?c. Calculate the yield of concrete if the mass of the batch is 4800 kg and its density is found to be 350 kg/m3.arrow_forwardUsing Figure 7.34, d. Plot the relationship between the moduli and the ultimate stresses on the same graph of part (c), using the relation of the ACI Building Code (Equation 7.3). e. Compare the two relations in questions c and d and comment on any discrepancies f. Determine the toughness at each water-cement ratio and comment on the effect of increasing water-cement ratio on the toughness of concrete.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Structural Analysis (10th Edition)Civil EngineeringISBN:9780134610672Author:Russell C. HibbelerPublisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Structural AnalysisCivil EngineeringISBN:9780073398006Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel LanningPublisher:McGraw-Hill Education
Traffic and Highway EngineeringCivil EngineeringISBN:9781305156241Author:Garber, Nicholas J.Publisher:Cengage Learning
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning
Concrete Slab Calculations 006; Author: Jerry Howard;https://www.youtube.com/watch?v=R19jILyBxio;License: Standard Youtube License