Materials for Civil and Construction Engineers (2nd Edition)

null Edition

ISBN: 9781292154411

Concept explainers

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon m…

Videos

Textbook Question

Chapter 6, Problem 6.28QP

Under what condition is an air-entraining agent needed? Why? Discuss how the air-entraining agent performs its function. What is the typical diameter of air-entrained voids?

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 6, Problem 6.27QP

Chapter 6, Problem 6.29QP

Students have asked these similar questions

Define yield of cement in slurry design?

a. What is the cumulative percent retained on the sieve with the highest percent retained? b. What is the percent passing on pan?

Define the minimum weight of fine aggregate for sieve analysis as per ASTM C136 ?

Chapter 6 Solutions

Materials for Civil and Construction Engineers (2nd Edition)

Ch. 6 - What ingredients are used for the production of...Ch. 6 - What is the role of gypsum in the production of...Ch. 6 - What is a typical value for the fineness of...Ch. 6 - What are the primary chemical reactions during the...Ch. 6 - Define the C-S-H phase of cement paste.Ch. 6 - What are the four main chemical compounds in...Ch. 6 - Prob. 6.7QP Ch. 6 - Define a. interlayer hydration space b. capillary...Ch. 6 - Prob. 6.9QP Ch. 6 - The following laboratory tests are performed: a....

Ch. 6 - What is a false set of portland cement? State one...Ch. 6 - The watercement ratio is important because it...Ch. 6 - Discuss the effect of watercement ratio on the...Ch. 6 - Draw a graph to show the general relationship...Ch. 6 - Students in the materials class prepared three...Ch. 6 - Students in the materials class prepared three...Ch. 6 - Two batches of cement mortar with properties as...Ch. 6 - What are the five primary types and functions of...Ch. 6 - Why isnt pozzolan used with Type III cement?Ch. 6 - What type of cement would you use in each of the...Ch. 6 - In order to evaluate the suitability of nonpotable...Ch. 6 - Three standard mortar cubes were made using...Ch. 6 - Four standard mortar cubes were made using...Ch. 6 - Discuss the problem of disposal of waste water...Ch. 6 - State five types of admixtures and discuss their...Ch. 6 - Prob. 6.27QP Ch. 6 - Under what condition is an air-entraining agent...Ch. 6 - If a water reducer is added to the concrete mix...Ch. 6 - Prob. 6.30QP Ch. 6 - A concrete mix includes the following ingredients...Ch. 6 - The results of an experiment to evaluate the...Ch. 6 - The results of a laboratory experiment to evaluate...Ch. 6 - Referring to Table P6.34, Mix No. 1 was designed...Ch. 6 - Two batches of concrete cylinders were made with...Ch. 6 - Two batches of concrete cylinders were made with...Ch. 6 - What is the source of fly ash? Why is fly ash...Ch. 6 - A materials engineer is working in a research...Ch. 6 - A materials engineer is working in a research...

Additional Engineering Textbook Solutions

Find more solutions based on key concepts

A 3 ft square footing carries a sustained load of 10 k. It is placed on the surface of a 30 ft thick saturated ...

Foundation Design: Principles and Practices (3rd Edition)

5.11 What error results on a 200-ft sight with a level if the rod reading is 6.307 ft but the top of the 7-ft r...

Elementary Surveying: An Introduction To Geomatics (15th Edition)

What production method for steel shapes is specified by the following organizations? AISI (American Iron and St...

Structural Steel Design (6th Edition)

1.2 Explain the difference between geodetic and plane surveys,

Elementary Surveying (14th Edition)

11-1. Determine the moments at A,B, and C, then draw the moment diagram for the beam. The moment of ine...

Structural Analysis (10th Edition)

A pipe flowing light oil has a manometer attached, as shown in Fig, P1.52. What is the absolute pressure in pip...

Fundamentals Of Thermodynamics

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Recommended textbooks for you

Structural Analysis
Civil Engineering
ISBN:9781337630931
Author:KASSIMALI, Aslam.
Publisher:Cengage,
Structural Analysis (10th Edition)
Civil Engineering
ISBN:9780134610672
Author:Russell C. Hibbeler
Publisher:PEARSON
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Structural Analysis
Civil Engineering
ISBN:9780073398006
Author:Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning
Publisher:McGraw-Hill Education
Sustainable Energy
Civil Engineering
ISBN:9781337551663
Author:DUNLAP, Richard A.
Publisher:Cengage,
Traffic and Highway Engineering
Civil Engineering
ISBN:9781305156241
Author:Garber, Nicholas J.
Publisher:Cengage Learning