Concept explainers
The material for a rod of cross-sectional area 2.70 in.2 and length 75.0 in. must be selected such that under an axial load of 120.000.0 lb. it will not yield and the elongation in the bar will remain below 0.105 in. (a) Provide a list of at least three different metals that would satisfy these conditions. (b) Narrow the list down if cost is an issue, (c) Narrow the list down if corrosion is an issue. Use Appendix I for properties and cost of common alloys only.
a)
The list of three different metals which satisfy the given condition.
Explanation of Solution
Write the expression for the stress acting in the rod.
Here, applied force is
Write the expression for the engineering strain as given as follows:
Here, change in length is
Write the expression for the Hook’s law as given as follows:
Here, stress is
Conclusion:
Substitute 120,000 lb for
Substitute 0.105 in for
The given rod is loaded with in the elastic region so hook’s law can be applied for obtaining the stress and strain values.
Substitute
The material that needs to satisfy the given specification should possess at least 200 GPa as Young’s modulus.
Refer the Appendix I, “5. Room temperature modulus of elasticity” obtain the following metals whose Young’s modulus values are equal to or more than 200 GPa.
- 1. Low alloy steels (Alloy 1006 cold drawn)
- 2. Stainless steels (Alloy 405 cold rolled annealed)
- 3. Miscellaneous alloys (Hayness 25 cold rolled and annealed)
b)
Choose the material based on the cost of the material.
Explanation of Solution
Refer the Appendix I “16. Cost and relative cost of some selected materials” obtain the cost of metals that are chosen in part (a) whose young’s modulus values are more than 218.66 GPa .
- 1. Low alloy steels (Alloy 1006 cold drawn) – 2.91 US $/lb
- 2. Stainless steels (Alloy 405 cold rolled annealed) – 394.79 US $/lb
- 3. Miscellaneous alloys (Hayness 25 cold rolled and annealed) – 40US $/lb
If cost is an issue, the best choice is Low alloy steels (Alloy 1006 cold drawn).
c)
Choose the material based on the cost of the corrosion.
Explanation of Solution
Refer part (a).
The materials are,
- 1. Low alloy steels (Alloy 1006 cold drawn)
- 2. Stainless steels (Alloy 405 cold rolled annealed)
- 3. Miscellaneous alloys (Hayness 25 cold rolled and annealed)
Residual stresses are induced when the material is cold worked. This residual stresses can cause corrosion, with proper annealing heat treatment residual stresses can be removed. Hence, comparing the stainless steels with miscellaneous alloys, the stainless steels will be the good choice and prevents the corrosion. Stainless steel alloys are readily available in the market.
Want to see more full solutions like this?
Chapter 6 Solutions
Connect Access Card For Foundations Of Materials Science And Engineering
Additional Engineering Textbook Solutions
Vector Mechanics for Engineers: Statics and Dynamics
Fluid Mechanics: Fundamentals and Applications
Fundamentals of Heat and Mass Transfer
Fox and McDonald's Introduction to Fluid Mechanics
Vector Mechanics for Engineers: Dynamics
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
- A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of 30,000 N. The rod is to experience an elongation not more than 1.3 mm and FOS ≥ 1.5 setting yield strength as a criteria. Additional constraints to be met are max specific stiffness and %EL not more than 0.15. Which of the below listed materials are possible candidates? Justify your choice(s) by making a table of constraints.arrow_forwardUnder an applied axial load, a rod elongates by 0.49 in. If the rod is 11 ft long, and has a 2.0 in. diameter. If the transverse deformation of the rod is 0.0024 in., calculate the material's Poisson's ratio: _____ . Pay calculate your answer to 3 significant figures.arrow_forwardI did a torsion test to experimentally calculate the brass modulus of rigidity. My experimental modulus value is lower than the published. What could have caused this?arrow_forward
- Give some examples of Ductile materials?arrow_forwardCalculate the maximum diameter that an Al2O3 bar must have without deforming if it is subjected to a load of 4502.0 N and has a yield strength of 230.1 MPaarrow_forwardWhich material/metal is the stiffest based on the following data provided and why?arrow_forward
- An aluminum rod is to withstand an applied force of 45,000 pounds. To assure sufficient safety, the maximum allowable stress on the rod is limited to 25,000 psi. The rod must be at least 150 in. long but must deform elastically no more than 0.25 in. when the force is applied. Design an appropriate rod.arrow_forwardExplain the difference between brittle and ductile materials?arrow_forwardTensile and fully reversed loading fatigue tests were conducted for a certain steel alloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa, respectively. If a rod of this material supply were subjected to a static stress of 600 MPa and oscillating stresses whose total range was 700 MPa, would you expect the rod to fail by fatigue processes? Hint: You may want to plot a diagram to aid in presenting your answer.arrow_forward
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning