OPERTATIONS MGMT:SUSTAINABILITY
2nd Edition
ISBN: 9781323751718
Author: HEIZER
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 6.S, Problem 53P
Summary Introduction
To determine: Average Outgoing Quality (AOQ).
Introduction: AOQ is the average quality of outgoing lots, which would be considered as the function of fraction defective. Both rejected and accepted lots would be included in outgoing lots.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Control charts for X̅and R are maintained on the outside diameter of a shaft.The subgroup size is 04. After 20 subgroups ∑ X̅= 43.75 and ∑R = 0.286. The specificationof the product is 2.15±0.02 unit. Products falling above and below the specification limitare rejected. The process is statistical controlled and normally distributed. Find the controllimits for X̅and R charts, Process capability, RPI of the process and % rejection. How toreduce the % of rejection if any?
An acceptance sampling plan has lots of 500pieces and a sample size of 60. The number of defects in thesample may not exceed 2. This plan, based on an OC curve,has a probability of .57 of accepting lots when the incominglots have a defective rate of 4%, which is the historical averagefor this process. What do you tell your customer the averageoutgoing quality is?
Design specifications require that a key dimensions on a product measures 346=12 units . A process is being considered for producing this product has a standard deviation of eight units. The process average has been shifted to 350 so that the process capability is 0.3333. Approximately, what percentage of items produced will be defective?
Chapter 6 Solutions
OPERTATIONS MGMT:SUSTAINABILITY
Ch. 6.S - Prob. 1DQCh. 6.S - Define in statistical control.Ch. 6.S - Prob. 3DQCh. 6.S - Prob. 4DQCh. 6.S - Prob. 5DQCh. 6.S - Prob. 6DQCh. 6.S - Prob. 7DQCh. 6.S - Prob. 8DQCh. 6.S - Prob. 9DQCh. 6.S - Prob. 10DQ
Ch. 6.S - Prob. 11DQCh. 6.S - Prob. 12DQCh. 6.S - Prob. 13DQCh. 6.S - Prob. 14DQCh. 6.S - Prob. 15DQCh. 6.S - Prob. 16DQCh. 6.S - Prob. 17DQCh. 6.S - Prob. 18DQCh. 6.S - Prob. 19DQCh. 6.S - Prob. 1PCh. 6.S - Prob. 2PCh. 6.S - Prob. 3PCh. 6.S - Prob. 4PCh. 6.S - Prob. 5PCh. 6.S - Prob. 6PCh. 6.S - Prob. 7PCh. 6.S - Prob. 8PCh. 6.S - Prob. 9PCh. 6.S - Prob. 10PCh. 6.S - Prob. 11PCh. 6.S - Prob. 12PCh. 6.S - Prob. 13PCh. 6.S - Prob. 14PCh. 6.S - Prob. 15PCh. 6.S - Prob. 16PCh. 6.S - Prob. 17PCh. 6.S - Prob. 18PCh. 6.S - Prob. 19PCh. 6.S - Prob. 20PCh. 6.S - Prob. 21PCh. 6.S - Prob. 22PCh. 6.S - Prob. 23PCh. 6.S - Prob. 24PCh. 6.S - Prob. 25PCh. 6.S - Prob. 26PCh. 6.S - Prob. 27PCh. 6.S - Prob. 40PCh. 6.S - Prob. 41PCh. 6.S - Prob. 42PCh. 6.S - Prob. 43PCh. 6.S - Prob. 44PCh. 6.S - Prob. 45PCh. 6.S - Prob. 51PCh. 6.S - Prob. 52PCh. 6.S - Prob. 53PCh. 6.S - Prob. 54PCh. 6.S - Prob. 55PCh. 6.S - Prob. 1CSCh. 6.S - Prob. 2CSCh. 6.S - Prob. 1.1VCCh. 6.S - Prob. 1.2VCCh. 6.S - Prob. 1.3VCCh. 6.S - Prob. 2.1VCCh. 6.S - Select two potential problems-one in the Darden...Ch. 6.S - Prob. 2.3VCCh. 6.S - Prob. 2.4VCCh. 6 - Prob. 1EDCh. 6 - Prob. 1DQCh. 6 - Prob. 2DQCh. 6 - Prob. 3DQCh. 6 - Prob. 4DQCh. 6 - Prob. 5DQCh. 6 - Prob. 6DQCh. 6 - Prob. 7DQCh. 6 - Prob. 8DQCh. 6 - Prob. 9DQCh. 6 - Prob. 10DQCh. 6 - Prob. 11DQCh. 6 - Prob. 12DQCh. 6 - Prob. 13DQCh. 6 - Prob. 14DQCh. 6 - Prob. 15DQCh. 6 - Prob. 16DQCh. 6 - Prob. 17DQCh. 6 - Prob. 18DQCh. 6 - An avant-garde clothing manufacturer runs a series...Ch. 6 - Prob. 2PCh. 6 - Prob. 3PCh. 6 - Prob. 4PCh. 6 - Kathleen McFaddens restaurant in Boston has...Ch. 6 - Prob. 6PCh. 6 - Prob. 7PCh. 6 - Prob. 8PCh. 6 - Prob. 9PCh. 6 - Prob. 10PCh. 6 - Prob. 11PCh. 6 - Prob. 12PCh. 6 - Prob. 13PCh. 6 - Prob. 14PCh. 6 - Prob. 15PCh. 6 - Prob. 16PCh. 6 - Prob. 17PCh. 6 - Prob. 1CSCh. 6 - Prob. 2CSCh. 6 - Prob. 3CSCh. 6 - Prob. 1.1VCCh. 6 - Prob. 1.2VCCh. 6 - Prob. 1.3VCCh. 6 - Prob. 1.4VCCh. 6 - Prob. 2.1VCCh. 6 - Prob. 2.2VCCh. 6 - Prob. 2.3VCCh. 6 - Prob. 2.4VCCh. 6 - Prob. 3.1VCCh. 6 - Prob. 3.2VCCh. 6 - Prob. 3.3VCCh. 6 - Prob. 3.4VCCh. 6 - Prob. 3.5VC
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, operations-management and related others by exploring similar questions and additional content below.Similar questions
- What is the effect on the cost of quality to the customer when in an agreement with a supplier to ensure all parts are within tolerance before shipment? My answer: Prevention and appraisal costs will increase while internal failure costs can either increase or decrease and external will decrease.arrow_forwardA manufacturing company has been inspecting units of output from a process. Each product inspected is evaluated on five criteria. If the unit does not meet standards for the criteria, it counts as a defect for the unit. Each unit could have as few as zero defects, and as many as five. After inspecting 2,000 units, they discovered 33 defects. What is the DPMO measure for this process?arrow_forwardWe have taken 12 samples of 400 book pages found the following proportions of defective pages: .01, .02, .02, .00, .01, .03, .02, .01, .00, .04, .03, and .02. A page is considered defective when one or more errors are detected. Calculate the control limits for a p control chart. A new sample of 400 pages is taken, and 6 pages are defective. Is the process still in control?arrow_forward
- A manufacturer receives shipments of several thousand parts from a supplier every week. The manufacturer has the option of conducting a 100 percent inspection before accepting the parts. The decision is based on a random sample of 15 parts. If parts are not inspected, defectives become apparent during a later assembly operation, at which time replacement cost is $6.25 per unit. Inspection cost for 100 percent inspection is $1 per unit. a. At what fraction defective would the manufacturer be indifferent between 100 percent inspection and leaving discovery of defectivesu ntil the later assembly operation? b. For the sample size used, what is the maximum number of sample defectives that would cause the lot to be passed without 100 percent inspection, based on your answer to part (a)?arrow_forwardDesign specifications require that a key dimension on a product measure 105 ± 12 units. A process being considered for producing this product has a standard deviation of four units. a. What can you say (quantitatively) regarding the process capability? Assume that the process is centered with respect to specifications. (Round your answer to 4 decimal places.) b. Suppose the process average shifts to 98. Calculate the new process capability. (Round your answer to 4 decimal places.) c. What is the probability of defective output after the process shift? (Use Excel's NORM.S.DIST() function to find the correct probability. Round "z" values to 2 decimal places. Round your answer to 4 decimal places.)arrow_forwardA manufacturing company has been inspecting units of output from a process. Each product inspected is evaluated on five criteria’s. If the unit does not meet standards for the criteria it counts as a defect for the unit. Each unit could have a few as zero defects, and as many as five. After inspecting 2,000 units, they discover 33 defects. What is the DPMO measure for this process? (Round to nearest whole number)arrow_forward
- Linda Boardman, I nc., an equipment manufacturerin Boston, has submitted a sample cutoff valve to improve yourmanufacturing process. Your process engineering department basconducted experiments and found that the valve has a mean (J.L)of 8.00 and a standard deviation (cr) of .04. Your desired performanceis f..L = 8.0 ±3cr, where cr = .045. What is the Cpk of theBoardman valve?arrow_forwardWhat is the upper confidence limit (3 sigma) for proportion defective when the average daily production is 2500 units with an established fraction defective of 0.05? Select one: a. 0.063 b. 0.066 c. 0.054 d. 0.058arrow_forwardA manufacturing company has been inspecting units of output from a process. Each prod uct inspected is evaluated on five criteria. If the unit does not meet standards for the criteria it counts as a defect for the unit. Each unit could have as few as zero defects, and as many as five. After inspecting 2,000 units, they discovered 33 defects. What is the DPMO measure for this process?arrow_forward
- We have taken 12 samples of 400 book pages found the following proportions of defective pages: .01, .02, .02, .00, .01, .03, .02, .01, .00, .04, .03, and .02. A page is considered defective when one or more errors are detected.a. Calculate the control limits for a p control chart.b. A new sample of 400 pages is taken, and 6 pages are defective.Is the process still in control?arrow_forwardWhich of the following statements about Pareto diagrams is correct?a. The Pareto diagram shows the possible root causes of a problem but does not show thefrequency of defect occurrences.b. The Pareto diagram shows the defects in order from most commonly occurring to leastcommonly occurring.c. The Pareto diagram shows the mean of a random sample at various points in time.d. The bars in the Pareto diagram have, on average, roughly the same height.arrow_forwardFor 50 consecutive days, a process engineer has measured the weight of acomponent after it has been coated with a special paint. Each day, she takes a sampleof 10 components. The average across all 500 components (50 days, 10 componentsper day) is 45.343018 grams. The standard deviation across all parts is 0.0076382 gram.When constructing an X-bar chart, what would be the center line and what would be thelines for the upper and lower control limits?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Practical Management ScienceOperations ManagementISBN:9781337406659Author:WINSTON, Wayne L.Publisher:Cengage,Operations ManagementOperations ManagementISBN:9781259667473Author:William J StevensonPublisher:McGraw-Hill EducationOperations and Supply Chain Management (Mcgraw-hi...Operations ManagementISBN:9781259666100Author:F. Robert Jacobs, Richard B ChasePublisher:McGraw-Hill Education
- Purchasing and Supply Chain ManagementOperations ManagementISBN:9781285869681Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. PattersonPublisher:Cengage LearningProduction and Operations Analysis, Seventh Editi...Operations ManagementISBN:9781478623069Author:Steven Nahmias, Tava Lennon OlsenPublisher:Waveland Press, Inc.
Practical Management Science
Operations Management
ISBN:9781337406659
Author:WINSTON, Wayne L.
Publisher:Cengage,
Operations Management
Operations Management
ISBN:9781259667473
Author:William J Stevenson
Publisher:McGraw-Hill Education
Operations and Supply Chain Management (Mcgraw-hi...
Operations Management
ISBN:9781259666100
Author:F. Robert Jacobs, Richard B Chase
Publisher:McGraw-Hill Education
Purchasing and Supply Chain Management
Operations Management
ISBN:9781285869681
Author:Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson
Publisher:Cengage Learning
Production and Operations Analysis, Seventh Editi...
Operations Management
ISBN:9781478623069
Author:Steven Nahmias, Tava Lennon Olsen
Publisher:Waveland Press, Inc.