MECH ENGINEERING DESIGN(LL)+ACCESS
10th Edition
ISBN: 9781260113952
Author: BUDYNAS
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 7, Problem 40P
A ball bearing has been selected with the bore size specified in the catalog as 35.000 mm to 35.020 mm. Specify appropriate minimum and maximum shaft diameters to provide a locational interference fit.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Calculate the basic rating life at 90% reliability for the following cylindrical roller bearing and conditions.Fr 5.05 kNFa 3.12 kNBearing: NU 1010 ECP (on pp 522 in the SKF catalogue)Clearance: Normal
Give the answer in millions of revolutions.
Consider that fit between the shaft and the disk is of transition type where the maximum interference is required to be 0,013 mm. Nominal diameter of the shaft is 65 mm. The hole in the disk is machined to IT quality of 7. tolerence on the fit is 0.050 mm. Using the basic shaft system, determine the nearest fit from ISO tables.
Select an angular contact ball bearing to carry a radial load of (336+ID) lb at a shaft speed of 1800 rpm for 5500 hours. An application factor of 1.2 is appropriate. Use a reliability of 96%.
(ID = 007)
Chapter 7 Solutions
MECH ENGINEERING DESIGN(LL)+ACCESS
Ch. 7 - A shaft is loaded in bending and torsion such that...Ch. 7 - The section of shaft shown in the figure is to be...Ch. 7 - The rotating solid steel shaft is simply supported...Ch. 7 - A geared industrial roll shown in the figure is...Ch. 7 - Design a shaft for the situation of the industrial...Ch. 7 - The figure shows a proposed design for the...Ch. 7 - For the problem specified in the table, build upon...Ch. 7 - Prob. 8PCh. 7 - For the problem specified in the table, build upon...Ch. 7 - For the problem specified in the table, build upon...
Ch. 7 - In the figure is a proposed shaft design to be...Ch. 7 - The shaft shown in the figure is proposed for the...Ch. 7 - Prob. 20PCh. 7 - The shaft shown in the figure is proposed for the...Ch. 7 - Prob. 25PCh. 7 - Prob. 26PCh. 7 - Prob. 27PCh. 7 - A 25-mm-diameter uniform steel shaft is 600 mm...Ch. 7 - Prob. 29PCh. 7 - Compare Eq. (727) for the angular frequency of a...Ch. 7 - Prob. 31PCh. 7 - The steel shaft shown in the figure carries a...Ch. 7 - A transverse drilled and reamed hole can be used...Ch. 7 - Prob. 34PCh. 7 - The shaft shown in Prob. 721 is proposed for the...Ch. 7 - A guide pin is required to align the assembly of a...Ch. 7 - Prob. 37PCh. 7 - Prob. 38PCh. 7 - Prob. 39PCh. 7 - A ball bearing has been selected with the bore...Ch. 7 - Prob. 41PCh. 7 - A gear and shaft with nominal diameter of 35 mm...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.arrow_forwardAccording to the data below, determine the life of FAG 6213 single row deep groove ball bearing to be used in the bearing of the rotary axis in hours. spindle speed = 2000 rpmloads: vertical radial:1600N horizontal radial:3600N axial: 1000 NBEARING FEATURES: NUMBER OF STATIC LOAD: 41.5 KN DYNAMIC LOAD NUMBER: 60KNarrow_forward15.)A full journal bearing has a journal diameter of 4.000in. with a unilateral tolerance of -0.004in. The bushing bore has a diameter of 4.004in and unilateral tolerance of +0.004in. the bearing is 3in long. The journal load is 3000 lbf and it runs at a speed of 400 rpm. What is the load per projected bearing area 9P) in psi? Choose answer below 75 100 125 250 16.)For the bearing in problem #15, if the lubricant average viscosity is 9 ureym, what is the Sommerfield number (assuming minimum clearance) Choose answer below Between 0.6 and 0.7 Between 0.5 and 0.6 Between 0.3 and 0.4 Between 0.2 and 0.3arrow_forward
- Select an angular contact ball bearing to carry a radial load of (336+01)lbat a shaft speed of 1800 rpm for 5500 hours. Anapplicationfactorof1.2isappropriate. Use a reliability of 96%.arrow_forwardOn section view AAa) What type of bearing is it?b) Is the assembly of these bearings rotating shaft or rotating hub?c) Is the mounting of the bearings in X, in O, …?d) Which rings (inner or outer) are mounted with interference?e) How many stops on the shaft are blocked?f) How many stops in the bore are blocked?g) Give the average tolerance of the seats of the inner rings located on the shaft.h) Give the average tolerance of the seats of the outer rings located on the bore.arrow_forwardDynamic load number C = 40500 N, revolution n = 840 rpm and Fr = 4500 of 6309 single row fixed radial bearing carrying N load; (a) Check and interpret whether it is selected correctly for Lh=20000 hours. (b) Calculate the dynamic load number of the bearing when the load remains the same and the life is doubled.arrow_forward
- ....The rating life at 90% reliability for a ball bearing is 15 x 106 revolutions. If the bearing is subjected to an equivalent radial load of 2000 N, which of the following is its dynamic load rating? Group of answer choices 4506 N 4932 N 1890 N 1665 Narrow_forwardA 02-series single-row deep-groove ball bearing is to be selected from Table 11–2 for the application conditions specified in the table. Assume Table 11–1 is applicable if needed. The value of radial load Fr = 8 kN, axial load Fa = 2 kN, design life LD = 2.40(108), ring rotation factor V = 1, and reliability RD = 0.98. Assuming that the values taken from Table 11–1 are X = 0.56 and Y = 1.63, determine the equivalent radial load rating for this application. What is the equivalent radial load rating for this application in kN?arrow_forwardConsider the belt drive having a diameter of 150 mm that is mounted on the overhung end of ashaft, 30 mm from the nearest bearing. The stepped shaft is made of steel having Su = 965 MPa(140 ksi). The shaft diameter, d, is 30 mm. The bearing bore, D, is 36 mm. The fillet with amachined surface has a radius, r, of 3 mm. What is the safety factor with respect to eventualfatigue failure of the shaft?arrow_forward
- An overhung countershaft is supported by rolling contact ball bearing. The shaft speed is 790 r.p.m. The bearings are to have 94% reliability corresponding to a life of 26000 hours. Compute and choose the value of nearest rating life L90. a. 4.9x109 rev. b. 8.6x109 rev. c. 1.9x109 rev. d. 6.2x109 rev.arrow_forwardA certain application requires a ball bearing with the inner ring rotating, with a design life of 26 kh at a speed of 455 rev/min. The radial load is 2.5 kN and an application factor of 1.2 is appropriate. The reliability goal is 0.92. Find the multiple of rating life required, xD , and the catalog rating C10 with which to enter a bearing table. Choose a 02-series deep-groove ball bearing from Table 11–2 and estimate the reliability in use.arrow_forwardAn 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
BEARINGS BASICS and Bearing Life for Mechanical Design in 10 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=aU4CVZo3wgk;License: Standard Youtube License