Principles of Foundation Engineering (MindTap Course List)
9th Edition
ISBN: 9781337705028
Author: Braja M. Das, Nagaratnam Sivakugan
Publisher: Cengage Learning
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 7, Problem 7.2P
In Problem 7.1, if there was no bedrock present for at least 12.0 ft below the foundation, what would the ultimate bearing capacity be?
7.1 A 7.5 ft wide rough continuous foundation is placed in the ground at 3.0 ft depth. There is bedrock present at 3 ft depth below the bottom of the foundation. The soil properties are c′ = 210 lb/ft2, ϕ′ = 25°, and γ = 115.0 lb/ft3. Determine the ultimate bearing capacity of the foundation.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A circular foundation of 1.5 m diameter is constructed in a sand deposit. Given: Df =1 5 m, soil friction angle Ø =35o and soil unit weight γ =17 4kN/m3. Estimate the ultimate uplift capacity of the foundation.
A 4.5m square foundation exerts uniform pressure of 200kn/m^2 on a soil . Determine
1:the vertical stress increment due to the foundation load to adepth of 10 m below its centre
2: the vertical stress increment at apoint 3m below the foundation and 4m from its centre along one of the axes of symmetry
A strip foundation (a long foundation in which the length is much longer than the width) of width 1m isused to transmit a load of 40kN/m from a block wall to the soil. Determine the increase in total verticalstress at a depth of 1m under the center and at the edge of the foundation.
Chapter 7 Solutions
Principles of Foundation Engineering (MindTap Course List)
Ch. 7 - A 7.5 ft wide rough continuous foundation is...Ch. 7 - In Problem 7.1, if there was no bedrock present...Ch. 7 - A 1.5 m × 2.0 m rectangular foundation is placed...Ch. 7 - In Problem 7.3, if no bedrock was present for at...Ch. 7 - Prob. 7.6PCh. 7 - Redo Problem 7.6 using Vesic’s (1975) solution...Ch. 7 - Prob. 7.8PCh. 7 - Prob. 7.9PCh. 7 - A continuous foundation having a width of 1.5 m is...Ch. 7 - A 2 m wide continuous foundation is to be placed...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A continuous foundation having a width of 1.4 m is supported by a saturated clay layer of limited depth underlain by a rock layer. Given that Df = 1 m, H = 0.7 m, cu = 105 kN/m2, and γ = 18 kN/m3, estimate the ultimate bearing capacity of the foundation.arrow_forwardA 2.0 m wide strip foundation is placed in sand at 1.0 m depth. The properties of the sand are: γ = 19.5 kN/m3, c′ = 0, and ф′ = 34°. Determine the maximum wall load that the foundation can carry, with a factor of safety of 3.0, using Terzaghi’s original bearing capacity equation with his bearing capacity factors, and Meyerhof’s general bearing capacity equation with shape, depth, and inclination factors from Table 6.3.arrow_forwardCalculate the settlement under the center of a flexible foundation 4 m by 4 m due to volume distortions occurring in a saturated clay stratum but where rock exists at a depth 8 m below the foundation. The clay shear strength c is 60 kPa. The total foundation loading imposed onto the soil is 2,400 kN.arrow_forward
- A 3 m thick clay layer (cu = 50 kN/m2 and γ = 19.0 kN/m3) is underlain by a weaker clay (cu = 30 kN/m2 and γ = 18.0 kN/m3) to a large depth. A 2.0 m wide square foundation is placed at 1.8 m depth below the ground level. Determine the maximum column load that can be allowed on the foundation with FS = 3.arrow_forwardA square foundation with dimensions 1m × 1m has to be constructed on a dense sand. The unit weight and the static angle of friction of the soil can be assigned representative values of 19.8 kN/m3 and 36 degrees, respectively. The foundation may occasionally be subjected to a maximum dynamic load of 600 kN increasing at a moderate rate. Determine the required minimum depth (Df) of the shallow foundation using a safety factor of 3.arrow_forwardA rectangular footing 6 x 3 m carries a uniform pressure of 300 kN/m 2 on the surface of a soil mass. Determine the vertical stress at a depth of 4.5 m below the surface on the center line 1.0 m inside the long edge of the foundation?arrow_forward
- A circular foundation 12 ft in diameter imposes a pressure of 8,000 psf onto the soil. At the 12-ft depth, determine the vertical stress increase beneath the center and the edge of the loaded area, assuming:(a) the Westergaard conditions apply.(b) the 60° approximation.arrow_forwardA square foundation is placed at a depth of 1.5 m within a sandy clay where c'=14k/m2 , phi'=23 and y=18 kN/m3 to carry a column load of 950 kN. Determine the width of the foundation that can be allowed on the foundation with a factor of safety of 3 and use the width value you have found to calculate the allowable bearing capacity(assume general shear failure and use gross values for the Terzaghi Bearing Capacity formulation for the given foundation type). If you don't write down the required equation to find the width of the foundation you cannot get credit from this question. Use the table given to you in the figure.arrow_forwardA column foundation (Figure P6.9) is 3 m × 2 m in plan. Given: Df = 1.5 m, ф′ = 25°, c′ = 70 kN/m2. Using Eq. (6.28) and FS = 3, determine the net allowable load [see Eq. (6.24)] the foundation could carry. Figure P6.9arrow_forward
- A square column foundation has to carry a gross allowable load of 1805 kN (FS = 3). Given: Df = 1.5 m, = 15.9 kN/m3, =34, and c = 0. Use Terzaghis equation to determine the size of the foundation (B). The applied load on a shallow square foundation makes an angle of 15 with the vertical. Given: B = 1.83 m, Df = 0.91 m, = 18.08 kN/m3, =25, and c = 23.96 kN/m2. Use FS = 4 and determine the gross allowable (vertical component) load. Use Eq. (16.9).arrow_forwardA 2.0 m wide square foundation is placed at 0.5 m depth ina saturated clay where cu= 40 kN/m2 and delta=19.0 kN/m3 .There is a very stiff stratum present at 1.0 m below the foundation. Determine the ultimate bearing capacity using Buisman’s (1940) equation.arrow_forwardThe excavation 3 × 6 m for a foundation is to be made to a depth of 2.5 m below ground level in a soil of bulkunit weight = 20 kN/m3.What effect this excavation will have on the vertical pressure at a depth of 6 m measuredfrom the ground surface vertically below the centre of foundation? The influence factor for m = 0.43 and n = 0.86 is 0.10.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning
Principles of Foundation Engineering (MindTap Cou...
Civil Engineering
ISBN:9781337705028
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
Fundamentals of Geotechnical Engineering (MindTap...
Civil Engineering
ISBN:9781305635180
Author:Braja M. Das, Nagaratnam Sivakugan
Publisher:Cengage Learning
CE 414 Lecture 02: LRFD Load Combinations (2021.01.22); Author: Gregory Michaelson;https://www.youtube.com/watch?v=6npEyQ-2T5w;License: Standard Youtube License