![MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)](https://s3.amazonaws.com/compass-isbn-assets/textbook_empty_images/large_textbook_empty.svg)
MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
2nd Edition
ISBN: 9781337551755
Author: DUNLAP
Publisher: Cengage Learning US
expand_more
expand_more
format_list_bulleted
Question
Chapter 8, Problem 20P
To determine
Find the thickness of concrete required to store the amount of energy.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A 2 x 2 m flat plate solar collector for domestic hot water heating is shown in the figure. The incident solar radiation on the glass cover, which transmits 90% of the incident flux, is 750 W/m2. Water flows through the tubes soldered to the backside of the absorber plate, entering at a temperature of 25°C. The temperature of the glass cover is 27°C, and it radiates heat with an emissivity of 0.92 to the sky at –50°C. Additionally, the glass cover losses heat by convection to air at 20°C flowing over its surface at 30 km/h. Assume that the radiation heat transfer between the absorber plate and glass cover and the heat transfer through the back and sides of the collector is negligible.
Consider a house that is approximated as a cube that is 8 m on a
side and has no windows. The house loses heat from the four
walls and the roof. For an inside temperature of 20°C and an
outside temperature of –20°C, it is desired to keep the total heat
loss less than 5 kW. What is the minimum RSj value that is
required for the walls and roof?
A wooden shelter has walls constructed of wooden planks 1.00 cm thick. If the exterior temperature is -20.0°C and the interior is 5.00°C, find the rate of energy loss through a wall that has dimensions 1.95 m by 2.30 m.
Chapter 8 Solutions
MindTap Engineering for Dunlap's Sustainable Energy, SI Edition, 2nd Edition [Instant Access], 1 term (6 months)
Knowledge Booster
Similar questions
- On a hot summer day, the flat roof of a tall building reaches 50° C in temperature. The area of the roof is 400m2. Estimate the heat radiated from this roof to the sky in the evening when the temperature of the surrounding air or sky is at 20° C. The temperature of the roof decreases as it cools down. Estimate the rate of energy radiated from the roof, assuming roof temperatures of 50, 40, 30, and 25° C. Assume ε = 0 9 . for the roof.arrow_forwardA line was measured to be 412 m using a 30-m tape, which is of standard length at a temperature of 20 deg.C. During measurement, the temperature was 52 deg.C. If the coefficient of thermal expansion of the tape material is 0.0000116 m/m deg.C, calculate the correct length of the line.arrow_forwardCalculate the thermal expansion of a concrete roof with the dimensions of 40 m×110 m for a temperature increase of 50°C. Assume the coefficient of thermal expansion.arrow_forward
- Calculate the amount of energy required in BTU to heat the air in a 10°F house 30 by 50 by 40 ft and increase the temperature by 70F at constant pressure.arrow_forwardAn insulated steam pipe having outside diameter of 3 cm is to be covered with two layers of insulation each having a thickness of 2.5 cm. the thermal conductivity of one material is 5 times that of the other assuming that the steam pipe surface temperature and outer air temperature remain fixed . how much change in heat transfer take place if the better insulating material is next to the pipe than it is on outer side?arrow_forwardA certain brand of hotdog cooker works by applying a potential difference of 146 V across opposite ends of a hot dog and allowing it to cook by means of the thermal energy produced. The current is 12.8 A, and the energy required to cook one hot dog is 60.8 kJ. If the rate at which energy is supplied is unchanged, how long will it take to cook three hot dogs simultaneously? Number i Unitsarrow_forward
- Question 10 Define thermal bridge in buildings, and explain how thermal bridge can be controlled in the following building components: Window frames: Balcony slab: Stud frame walls: Roof to wall connection: Window to wall connection:arrow_forwardA glass windowpane in a home is 0.62 cm thick and has dimensions of 1.4 m x 1.9 m. On a certain day, the indoor temperatu 24°C and the outdoor temperature is 0°C. (a) What is the rate at which energy is transferred by heat through the glass? W (b) How much energy is lost through the window in one day, assuming the temperatures inside and outside remain constant?arrow_forwardA home is heated with propane with a 100,000 BTU furnace size and 95% efficiency. The monthly heating degree days is 5000. Using the energy estimation discussed in this chapter, estimate the monthly and annual gas consumption to heat the building if the home is to be kept 68°F.arrow_forward
- A dual-pane window in a house is composed of two parallel panes of glass, each with an area of 2.23 m². Each pane of glass is 3.10 mm thick and the space between the panes is 12.5 mm thick and is filled with argon. (a) Calculate the heat flow through the window if the indoor temperature is 18.3°C and the outdoor temperature is -20.6°C (this is about -5°F). (b) Determine the temperature on the inside of the pane (this is in the argon-dilled region) closest to the outside of the house.arrow_forwardA closed tank containing hot air has an initial internal energy of 400 kJ. During the next 5 min, the tank loses heat to the surroundings at a rate of 1.5 kW, while an electrical element supplies 1000 W to the air. Find the final internal energy of the air.arrow_forwardList down three to five situations in which buildings, roads or other structures has been built to make room for thermal expansion of different materials.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
