EBK AUTOMOTIVE TECHNOLOGY
5th Edition
ISBN: 9780100659841
Author: Halderman
Publisher: YUZU
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 8, Problem 2CQ
Technician A says that the diameter of a bolt is the same as the wrench size used to remove or install the fastener. Technician B says that the length is measured from the top of the head of the bolt to the end of the bolt Which technician is correct?
- a. Technician A only
- b. Technician B only
- c. Both Technicians A and B
- d. Neither Technician A nor B
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Distinguish nominal diameter and gross diameter of bolt
Technician A says a metric bolt with the marking of 8.9 has more yield strength than a 10.9 bolt. Technician B says only grade 8 nuts should be used on 10.9 rated bolt. Who is correct?
Identify the part not belonging to micrometer.
Frame
Ratchet
Locknut
Clamp
Chapter 8 Solutions
EBK AUTOMOTIVE TECHNOLOGY
Ch. 8 - What is the difference between a bolt and a stud?Ch. 8 - Prob. 2RQCh. 8 - Prob. 3RQCh. 8 - Prob. 4RQCh. 8 - How are threaded inserts installed?Ch. 8 - The thread pitch of a bolt is measured in what...Ch. 8 - Technician A says that the diameter of a bolt is...Ch. 8 - The grade of a fastener, such as a bolt, is a...Ch. 8 - Prob. 4CQCh. 8 - Prob. 5CQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In a tap set, a taper tap is used to start a thread form in a drilled hole Select one: True Falsearrow_forwardWhich of the following wrenches is the best choice for torquing a bolt? Open-end Box-end Combination None of the abovearrow_forwardWhich of the following wrenches is the best choice fortorquing a bolt?a. Open-endb. Box-endc. Combinationd. None of the abovearrow_forward
- Which of the following is the correct order of doing a fitting job? B. Clamping on vice- Marking -Filing -Surface finishing C. Marking -Filing - Surface finishing- Clamping on vice D. Marking - Clamping on vice -Filing - Surface finishing A. Surface finishing-Clamping on vice-Filing-Markingarrow_forwardA tool make easy work of removing broken threaded ends of pipe, plugs & fittings. A tool make easy work of removing broken threaded ends of pipe, plugs & fittings. Pipe Reamer Pipe Vise Pipe Extractor Flaring tool Pipe taparrow_forwardDescribe the procedure for preparing and threading the end of steel pipe.arrow_forward
- Which of the following is the most common method of snug tightening bolts? O Heat tightening O Tension Control Bolting O Angle Tightening (Turn of Nut) O Direct Tension Indicatorsarrow_forwardA vehicle makes a loud clicking sound during a left turn; during a right turn, the clicking noise is still apparent but is less pronounced. Technician A says that the left inner CV joint may be the source of the noise. Technician B says that the left outer CV joint may be causing the noise. Who is correct? O a. A only Ob.B only O c. Both A and B O d. Neither A nor Barrow_forwardMeat mallet information with picture.arrow_forward
- Bolt material is 304 stainless steel. frame material is Aluminum. kindly assume all the other values and find the bolt size / diameter for bolt. write all formulas and explain the procedure. there are 2 bolts 1 on left and 1 on right.arrow_forwardCan I get the Top, Side and views. Using free-hand drawing of this coupling pieces..arrow_forwardA ball and a socket joint forms aarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage LearningRefrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
- Welding: Principles and Applications (MindTap Cou...Mechanical EngineeringISBN:9781305494695Author:Larry JeffusPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
Welding: Principles and Applications (MindTap Cou...
Mechanical Engineering
ISBN:9781305494695
Author:Larry Jeffus
Publisher:Cengage Learning
Stresses Due to Fluctuating Loads Introduction - Design Against Fluctuating Loads - Machine Design 1; Author: Ekeeda;https://www.youtube.com/watch?v=3FBmQXfP_eE;License: Standard Youtube License