Sustainable Energy
2nd Edition
ISBN: 9781337551663
Author: DUNLAP, Richard A.
Publisher: Cengage,
expand_more
expand_more
format_list_bulleted
Question
Chapter 8, Problem 7P
To determine
Find the time required for the water to reach
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
A 75 gal. electric hot water heater provides 9000 Watts of power to heat water. If the heater is filled with water at an initial temperature of 50ºF, how long will it take for the water to reach 140ºF? Assume that there are no heat losses.
A heat pump supplies heat energy to a house at the rate of 140,000 kJ/h when the house is maintained at 25°C. Over a period of one month, the heat pump operates for 100 hours to transfer energy from a heat source outside the house to inside the house. Consider a heat pump receiving heat from two different outside energy sources. In one application the heat pump receives heat from the outside air at 0°C. In a second application the heat pump receives heat from a lake having a water temperature of 10°C. If electricity costs $0.105/kWh, determine the maximum money saved by using the lake water rather than the outside air as the outside energy source.
For a building located in Madrid, Spain with annual heating degree-days (dd) of 4654, a heating load (heat loss) of 30,000 kj/h, and a design temperature difference of 30° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 92%, how muchgas is burned to keep the home at 20° C? State your assumptions.
Knowledge Booster
Similar questions
- A coal-fired power plant discharges 1 m^3/s of cooling water into a river, which has a flow of 9 m^3/s and a temperature of 20 degree C. According to the regulation, the temperature in the river immediately below the discharge cannot be increased by higher than 1 degree C. Therefore, what is the highest temperature of the cooling water is allowed for discharge?arrow_forwardThe heat exchanger radiates thermal energy at the rate of 2500 kJ/h for each square meter of its surface area. Determine how many joules (J) are radiated within a 5-hour period.arrow_forwardA stove element draws 15 A when connected to a 240-V line. How long does it take to consume 60 kJ .arrow_forward
- Replacing incandescent lights with energy-efficient fluorescent lights can reduce the lighting energy consumption to one-fourth of what it was before. The energy consumed by the lamps is eventually converted to heat, and thus switching to energy-efficient lighting also reduces the cooling load in summer but increases the heating load in winter. Consider a building that is heated by a natural gas furnace with an efficiency of 80 percent and cooled by an air conditioner with a COP of 3.5. If electricity costs $0.12/kWh and natural gas costs $1.40/therm (1 therm = 105,500 kJ), determine if efficient lighting will increase or decrease the total energy cost of the building (a) in summer and (b) in winter.arrow_forwardWhen 1 cu ft of natural gas is burned, 1,050 Btu of heat are produced. In oneday, a building uses 761,250 Btu of heat. How many cubic feet of gas areburned?arrow_forwardFor a building located in London, England with annual heating degree-days (dd) of 5634, a heating load (heat loss) of 42,000 kj/h, and a design temperature difference of 35° C (20° C indoor), estimate the annual energy consumption. If the building is heated with a furnace with an efficiency of 98%, how much gas is burned to keep the home at 20° C? State yourassumptions.arrow_forward
arrow_back_ios
arrow_forward_ios
Recommended textbooks for you
Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning