FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
6th Edition
ISBN: 9781265141387
Author: Anderson
Publisher: MCG
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 8, Problem 8.13P
Repeat Problems 8.11 and 8.12 using (incorrectly) Bernoulli’s equation for incompressible flow. Calculate the percent error induced by using Bernoulli’s equation.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
6- Discussion:
1. Sketch a diagram for the experimental instrumentation and devices.
2. State any possible error source in the experiment.
3. State any suggestions to improve the experiment (visit youtube.com).
4. Compare the exact value with that obtained experimentally and estimate the error percentage.
5. What is mean by compressible and incompressible flow?
6. How does the specific heat of the air change with temperature?
7. Suggest another way to measure the air velocity by using a manometer?
Calculate the flow rate (Q) of the following SAE 40 oil distribution system considering the characteristics described in the schematic.
Direction: Solve the following problems. Please box your final answer and write your solution clearly.
A pump discharges a liquid into a drum at the rate of 0.032 m3/s. The drum, 1.5m in diameter and 4.2m in length, can hold 3000kg of the liquid. Find the density of the liquid and the mass flow rate of the liquid handled by the pump.
A cargo ship has tanks for carrying fuel oil. The oil is measured in barrels, while the tank dimensions are in meters, 1m x 5m x 15m. How many barrels does the tank hold? How many gallons? (42 gal = 1 barrel)
Chapter 8 Solutions
FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
Ch. 8 - Consider air at a temperature of 230 K. Calculate...Ch. 8 - The temperature in the reservoir of a supersonic...Ch. 8 - At a given point in a flow, T=300K,p=1.2atm, and...Ch. 8 - At a given point in a flow, T=700R,p=1.6atm, and...Ch. 8 - Consider the isentropic flow through a supersonic...Ch. 8 - Consider the isentropic flow over an airfoil. The...Ch. 8 - The flow just upstream of a normal shock wave is...Ch. 8 - The pressure upstream of a normal shock wave is 1...Ch. 8 - The entropy increase across a normal shock wave is...Ch. 8 - The how just upstream of a normal shock wave is...
Ch. 8 - Consider a flow with a pressure and temperature of...Ch. 8 - Consider a flow with a pressure and temperature of...Ch. 8 - Repeat Problems 8.11 and 8.12 using (incorrectly)...Ch. 8 - Derive the Rayleigh Pitot tube formula, Equation...Ch. 8 - On March 16, 1990, an Air Force SR-71 set a new...Ch. 8 - In the test section of a supersonic wind tunnel, a...Ch. 8 - When the Apollo command module returned to earth...Ch. 8 - The stagnation temperature on the Apollo vehicle...Ch. 8 - Prove that the total pressure is constant...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- 7.8 A turboblower develops 750 mm W.G. at a speed of 1480 rpm and a flow rate of 38 m³/s. It is desired to build a small model which develops the same head at a higher speed (2940 rpm) and low discharge. Determine the specific speed and the flow rate through the model.arrow_forwardFor a junction if pipe 1 diameter = 50 mm, mean velocity 2 m/s, pipe 2 diameter 40 mm takes 30% of total discharge and pipe 3 diameter 60 mm. Find the discharge in I/hr and velocity through each pipe? Comments on the results.arrow_forwardUse g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 secarrow_forward
- Given problem: a.) At temperatures of 100° F and 120 psi absolute, calculation of above properties for methane (CH4): what is the barometric pressure if the gauge reading is 104.5 Psig? b.) A pipe transports an incompressible fluid. The volume flow rate is 10m3/s at point 1 along the pipe. The area halves at spot 2 along the pipe. At site 2, what is the volume flow rate?arrow_forwardSuppose we have planned to design a hydraulic system.In this aspect, the pump selection is to be finalized for a flow rate of 3464.5 Liters per minute, It has been validated that the fluid velocity in a discharge pipeline should be between 4.6 m/s and 6.8 m/s. Calculate the minimum diameter and maximum diameter of pipe that should be used in the pipelines. Write the significance of using maximum diameter pipelines in the hydraulic systemarrow_forwardV:32) The jet on a water feature shoots a column of water 75 ft. high. The nozzle is located just above the surface of a reflecting pool and has a diameter of 2 in. A submersible pump with a 4 in dia outlet and an 8 in. diameter intake pipe located 3.25 ft. below the surface of the pool operates the jet.1. Write an expression to determine the velocity of the water coming out of the nozzle.2. Find the velocity of the water at the nozzle exit.3. Find the velocity at point A just inside the inlet.arrow_forward
- For an incompressible flow machine define the flow coefficient. At what speed the blade must run to get a flow coefficient equal to 0.5. if the average meridional speed is 100 m/s,arrow_forward1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p-6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = V(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? c. Assume the pressure gradient is uniform on the cross-section and can be calculated using - The velocity profile in the cylinder is u(r) = [1-2²]. Sketch the velocity profile. Calculate the shear stress at the ax 2μ δχ cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L r L. Rarrow_forward1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p=6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = PV(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? LL c. Assume the pressure gradient is uniform on the cross-section and can be calculated using OP=-. The velocity profile in the cylinder is u(r) = ax - [1-(²]. Sketch the velocity profile. Calculate the shear stress at the R² ap 2UÔI cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L L. Rarrow_forward
- Please solve using turbulent flow equations.arrow_forward2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal placesarrow_forwardAssignment brief Task 1: Incompressible flow In the nozzle section of a wind tunnel sħown in Figure 1, the throat to the inlet area ratio is 0.06. The tunnel is turned on, and the pressure difference between the inlet (the settling chamber) and the test section is read as a height difference of 54 mm on a U-tube water manometer. The pressure and temperature of the airflow in the settling chamber (section 1) are 9.66 x 10* N/m² and 285.56 K, respectively. a) Calculate the temperature and pressure of the airflow in the test section (section 2) b) Calculate the velocity and Mach number of the airflow in the test section. c) If the exit to the throat area ratio is 12, calculate the velocity, pressure, and Mach number of the airflow in the exit section. Settling Chamber Exit section Test Section Diffuser Nozzle P. P. A Ah Figure 1: Wind tunnel ওarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License