FLUID MECHANICS >C<
18th Edition
ISBN: 9781308529622
Author: White
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 8, Problem 8.50P
It is desired to simulate flow past a two-dimensional ridge or bump by using a streamline that passes above the flow over a cylinder, as in Fig. P8.50. The bump is to be a/2 high, where a is the cylinder radius. What is the elevation h of this streamline? What is Umax on the bump compared with stream velocity U?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Assume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively.
Consider the lifting flow over a circular cylinder of a given radius and witha given circulation. If V∞ is doubled, keeping the circulation the same,does the shape of the streamlines change? Explain.
Air flows through a 6-cm-diameter smooth pipe that has a2-m-long perforated section containing 500 holes (diameter1 mm), as in Fig. . Pressure outside the pipe issea-level standard air. If p1 = 105 kPa and Q1 = 110 m3/h,estimate p2 and Q2, assuming that the holes are approximatedby thin-plate orifices. (Hint: A momentum controlvolume may be very useful.)
A uniform stream, U∞ = 4 m/s, approaches a Rankine ovalas in Fig. with a = 50 cm. Find the strength m of thesource-sink pair, in m2/s, which will cause the total lengthof the oval to be 250 cm. What is the maximum width ofthis oval?
Chapter 8 Solutions
FLUID MECHANICS >C<
Ch. 8 - Prob. 8.1PCh. 8 - The steady plane flow in Fig. P8.2 has the polar...Ch. 8 - P8.3 Using cartesian coordinates, show that each...Ch. 8 - P8.4 Is the function 1/r a legitimate velocity...Ch. 8 - Prob. 8.5PCh. 8 - An incompressible plane flow has the velocity...Ch. 8 - Prob. 8.7PCh. 8 - For the velocity distribution u=By,=+Bx , evaluate...Ch. 8 - Prob. 8.9PCh. 8 - Prob. 8.10P
Ch. 8 - Prob. 8.11PCh. 8 - Prob. 8.12PCh. 8 - P8.13 Starting at the stagnation point in Fig....Ch. 8 - P8.14 A tornado may be modeled as the circulating...Ch. 8 - Hurricane Sandy, which hit the New Jersey coast on...Ch. 8 - Prob. 8.16PCh. 8 - P8.17 Find the position (x, y) on the upper...Ch. 8 - Prob. 8.18PCh. 8 - Prob. 8.19PCh. 8 - Plot the streamlines of the flow due to a line...Ch. 8 - P8.21 At point A in Fig. P8.21 is a clockwise line...Ch. 8 - P8.22 Consider inviscid stagnation flow, (see...Ch. 8 - P8.23 Sources of strength m = 10 m2/s are placed...Ch. 8 - P8.24 Line sources of equal strength m = Ua, where...Ch. 8 - Prob. 8.25PCh. 8 - Prob. 8.26PCh. 8 - Prob. 8.27PCh. 8 - Sources of equal strength m are placed at the four...Ch. 8 - Prob. 8.29PCh. 8 - Prob. 8.30PCh. 8 - A Rankine half-body is formed as shown in Fig....Ch. 8 - Prob. 8.32PCh. 8 - P8.33 Sketch the streamlines, especially the body...Ch. 8 - Prob. 8.34PCh. 8 - Prob. 8.35PCh. 8 - Prob. 8.36PCh. 8 - Prob. 8.37PCh. 8 - Consider potential flow of a uniform stream in the...Ch. 8 - A large Rankine oval, with a = 1 m and h = 1 m, is...Ch. 8 - Prob. 8.40PCh. 8 - Prob. 8.41PCh. 8 - Prob. 8.42PCh. 8 - P8.43 Water at 20°C flows past a 1-rn-diameter...Ch. 8 - Prob. 8.44PCh. 8 - Prob. 8.45PCh. 8 - P8.46 A cylinder is formed by bolting two...Ch. 8 - Prob. 8.47PCh. 8 - Prob. 8.48PCh. 8 - Prob. 8.49PCh. 8 - It is desired to simulate flow past a...Ch. 8 - Prob. 8.51PCh. 8 -
P8.52 The Flettner rotor sailboat in Fig. E8.3...Ch. 8 - P8.52 The Flettner rotor sailboat in Fig. E8.3 has...Ch. 8 - Prob. 8.54PCh. 8 - Prob. 8.55PCh. 8 - Prob. 8.56PCh. 8 - Prob. 8.57PCh. 8 - Prob. 8.58PCh. 8 - Prob. 8.59PCh. 8 - Prob. 8.60PCh. 8 - Prob. 8.61PCh. 8 - Prob. 8.62PCh. 8 - The superposition in Prob. P8.62 leads to...Ch. 8 - Consider the polar-coordinate stream function...Ch. 8 - Prob. 8.65PCh. 8 - Prob. 8.66PCh. 8 - Prob. 8.67PCh. 8 - Prob. 8.68PCh. 8 - Prob. 8.69PCh. 8 - Prob. 8.70PCh. 8 - Prob. 8.71PCh. 8 - Prob. 8.72PCh. 8 - Prob. 8.73PCh. 8 - Prob. 8.74PCh. 8 - Prob. 8.75PCh. 8 - Prob. 8.76PCh. 8 - Prob. 8.77PCh. 8 - Prob. 8.78PCh. 8 - Prob. 8.79PCh. 8 - Prob. 8.80PCh. 8 - Prob. 8.81PCh. 8 - Prob. 8.82PCh. 8 - Prob. 8.83PCh. 8 - Prob. 8.84PCh. 8 - Prob. 8.85PCh. 8 - Prob. 8.86PCh. 8 - Prob. 8.87PCh. 8 - Prob. 8.88PCh. 8 - Prob. 8.89PCh. 8 - NASA is developing a swing-wing airplane called...Ch. 8 - Prob. 8.91PCh. 8 - Prob. 8.92PCh. 8 - Prob. 8.93PCh. 8 - Prob. 8.94PCh. 8 - Prob. 8.95PCh. 8 - Prob. 8.96PCh. 8 - Prob. 8.97PCh. 8 - Prob. 8.98PCh. 8 - Prob. 8.99PCh. 8 - Prob. 8.100PCh. 8 - Prob. 8.101PCh. 8 - Prob. 8.102PCh. 8 - Prob. 8.103PCh. 8 - Prob. 8.104PCh. 8 - Prob. 8.105PCh. 8 - Prob. 8.106PCh. 8 - Prob. 8.107PCh. 8 - P8.108 Consider two-dimensional potential flow...Ch. 8 - Prob. 8.109PCh. 8 - Prob. 8.110PCh. 8 - Prob. 8.111PCh. 8 - Prob. 8.112PCh. 8 - Prob. 8.113PCh. 8 - Prob. 8.114PCh. 8 - Prob. 8.115PCh. 8 - Prob. 8.1WPCh. 8 - Prob. 8.2WPCh. 8 - Prob. 8.3WPCh. 8 - Prob. 8.4WPCh. 8 - Prob. 8.5WPCh. 8 - Prob. 8.6WPCh. 8 - Prob. 8.7WPCh. 8 - Prob. 8.1CPCh. 8 - Prob. 8.2CPCh. 8 - Prob. 8.3CPCh. 8 - Prob. 8.4CPCh. 8 - Prob. 8.5CPCh. 8 - Prob. 8.6CPCh. 8 - Prob. 8.7CPCh. 8 - Prob. 8.1DPCh. 8 - Prob. 8.2DPCh. 8 - Prob. 8.3DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- SAE 30 oil at 20 °C flows at 1.8 ft3/s from a reservoir into a6-in-diameter pipe. Use flat-plate theory to estimate theposition x where the pipe wall boundary layers meet in thecenter. Compare with Eq., Le/d≈ 0.06 Red laminar and give some explanationsfor the discrepancy.arrow_forwardFor the pitot-static pressure arrangement of Fig.,the manometer fluid is (colored) water at 20°C. Estimate(a) the centerline velocity, (b) the pipe volume flow, and(c) the (smooth) wall shear stress.arrow_forwardLet the vortex/sink flow of Eq. (8.16) simulate a tornado as inFig. . Suppose that the circulation about the tornado isΓ = 8500 m2/s and that the pressure at r = 40 m is 2200 Paless than the far-field pressure. Assuming inviscid flow at sea-leveldensity, estimate (a) the appropriate sink strength 2m,(b) the pressure at r = 15 m, and (c) the angle β at which thestreamlines cross the circle at r = 40 m (see Fig. ).arrow_forward
- Air flows at 1.2 m/s along with a flat surface when it encountersa jet of air issuing from the horizontal wall at point A, as inFig. P8.16. The jet volume flow is 0.4 m3/s per unit depthinto the paper. If the jet is approximated as an inviscid linesource, (a) locate the stagnation point S on the wall.(b) How far vertically will the jet flow extend into the stream?arrow_forwardAn engineer claims that the flow of SAE 30W oil, at 20 °C,through a 5-cm-diameter smooth pipe at 1 million N/h, islaminar. Do you agree? A million newtons is a lot, so thissounds like an awfully high flow rate.arrow_forwardAssume an inviscid, incompressible flow. Also, standard sea level density and pressure are 1.23 kg/m3 (0.002377 slug/ft3) and 1.01 × 105 N/m2 (2116 lb/ft2), respectively. Derive the velocity potential for a doublet.arrow_forward
- Water at 20 ° C flows down through a vertical, 6-cm diametertube at 300 gal/min, as in Fig. P3.74. The flowthen turns horizontally and exits through a 90 ° radial ductsegment 1 cm thick, as shown. If the radial outflow is uniformand steady, estimate the forces ( F x , F y , F z ) required tosupport this system against fluid momentum changes.arrow_forwardAerodynamics NACA 747A415, chord is 180 cm 1) What is the location of favorable pressure gradient of the upper surface, measured from LE? 2) What is the location favorable pressure gradient of the upper surface, measured from TE?arrow_forwardWater at 20°C flows past a 1-m-diameter circular cylinder.The upstream centerline pressure is 128,500 Pa. If the lowestpressure on the cylinder surface is exactly the vaporpressure, estimate, by potential theory, the stream velocity.arrow_forward
- A two-dimensional Rankine half-body, 8 cm thick, isplaced in a water tunnel at 20°C. The water pressure farupstream along the body centerline is 105 kPa. What isthe nose radius of the half-body? At what tunnel flowvelocity will cavitation bubbles begin to form on the surfaceof the body?arrow_forwardThe bottom of a river has a 4-m-high bump that approximates a Rankine half-body, as in Fig. The pressure at point B on the bottom is 130 kPa, and the river velocity is 2.5 m/s. Use inviscid theory to estimate the water pressure at point A on the bump, which is 2 m above point B.arrow_forwardtall water tank discharges through a well-rounded orifi ce,as in Fig. P3.95. Use the Torricelli formula to estimate the exit velocity. ( a ) If, at this instant, the forceF required to hold the plate is 40 N, what is the depth h ?( b ) If the tank surface is dropping at the rate of 2.5 cm/s,what is the tank diameter D ?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License