(a) Explanation Given information: The magnitude of load P 1 is 1 , 080 lb . The magnitude of load P 2 is 810 lb . Refer to problem P8.19 in the textbook. The diameter ( d ) of the shaft is 1.75 in . Calculation: Refer to problem P8.19 in the textbook. Find the value of c using the relation: c = 1 2 d (1) Here, d is the diameter of the shaft. Substitute 1.75 in . for d in Equation (1). c = 1 2 × 1.75 = 0.875 in . Find the polar moment of inertia ( J ) using the relation: J = π 2 c 4 (2) Here, c is the half of the diameter. Substitute 0.875 in for c in Equation (2). J = π 2 ( 0.875 ) 4 = 0.92077 in 4 Sketch the free body diagram of horizontal plane as shown in Figure 1. Calculate the reaction for the given structure. Taking a moment about B , ∑ M B = 0 D y × 20 − ( 810 × 10 ) = 0 20 D y − 8 , 100 = 0 D y = 405 lb ∑ F y = 0 A y + D y = 810 (3) Substitute 405 lb for D y in Equation (3). B y + 405 = 810 B y = 405 lb Calculate the bending moment in horizontal plane at point C . B M D = 405 × 10 = 4 , 050 lb ⋅ in Sketch the bending moment diagram in horizontal plane as shown in Figure 2. Calculate the shear force in vertical plane just to the left of point B as follows: Refer to Figure 3, S F A = 1 , 080 lb Calculate the bending moment in vertical plane just to the left of point B as follows: Refer to Figure 3, B M C = 1 , 080 × 13 − ( 1 , 242 × 10 ) = 14 , 040 − 12 , 420 = 1 , 620 lb ⋅ in B M B = 1 , 080 × 3 = 3 , 240 lb ⋅ in Find the value of Torque over portion ABC . T = 6 × 1 , 080 = 6 , 480 lb ⋅ in Sketch the bending moment diagram in vertical plane as shown in Figure 3. Sketch the cross section left of point B as shown in Figure 4 (b) To determine The values of τ H and τ K in a section just to the left C .

7th Edition

ISBN: 9789814595247

Author: Ferdinand Beer

Publisher: Mcgraw-Hill

See similar textbooks

Videos

Question

Chapter 8.2, Problem 22P

(a)

To determine

The values of τH and τK in a section just to the left B.

(b)

To determine

The values of τH and τK in a section just to the left C.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 8.2, Problem 21P

Chapter 8.2, Problem 23P

Students have asked these similar questions

Two links BF are made of steel with a 450-MPa ultimate normal stress and has a 6x12–mm uniform rectangular cross section. Links BF are connected to members ABD and CDEF by 8-mm diameter pins; ABD and CDEF are connected together by a 10-mm diameter pin; CDEF is connected to the support by a 10-mm diameter pin; all of the pins are made of steel with a 170 MPa ultimate shearing stress. Knowing that a factor of safety of 3 is desired, determine the largest load P that may be applied

In the structure shown, an 8-mm-diameter pin is used at A, and 12-mm-diameter pins are used at B and D. Knowing that the ultimate shearing stress is 100 MPa at all connections and that the ultimate normal stress is 250 MPa in each of the two links joining B and D, determine the allowable load P if an overall factor of safety of 2.6 is desired.

Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts fitting snugly inside cylindrical brass spacers. Knowing that the average normal stress must not exceed 205 MPa in the bolts and 132 MPa in the spacers, determine the outer diameter of the spacers that yields the most economical and safe design. The outer diameter of the spacers that yields the most economical and safe design is mm.

Chapter 8 Solutions

Mechanics Of Materials - Si Version

Ch. 8.2 - A W10 = 39 rolled-steel beam supports a load P as...Ch. 8.2 - Solve Prob. 8.1, assuming that P = 22.5 kips and a...Ch. 8.2 - An overhanging W920 449 rolled-steel beam...Ch. 8.2 - Solve Prob. 8.3, assuming that P = 850 kN and a =...Ch. 8.2 - 8.5 and 8.6 (a) Knowing that all = 160 MPa and all...Ch. 8.2 - 8.5 and 8.6 (a) Knowing that all = 160 MPa and all...Ch. 8.2 - 8.7 and 8.8 (a) Knowing that all = 24 ksi and all...Ch. 8.2 - 8.7 and 8.8 (a) Knowing that all = 24 ksi and all...Ch. 8.2 - 8.9 through 8.14 Each of the following problems...Ch. 8.2 - 8.9 through 8.14 Each of the following problems...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

The values of τ H and τ K in a section just to the left B .

Solution Summary: The author calculates the polar moment of inertia (J) using the relation: cj=pi 2

Videos

The values of τH and τK in a section just to the left B.

The values of τH and τK in a section just to the left C.

Want to see the full answer?

Chapter 8 Solutions