A cylinder having a mass of 250 kg is to be supported by the cord that wraps over the pipe. Determine the smallest vertical force F needed to support the load if the cord passes (a) once over the pipe, β = 180°, and (b) two times over the pipe, β = 540°. Take, μs = 0.2.
Learn your wayIncludes step-by-step video
Chapter 8 Solutions
Engineering Mechanics: Statics Plus Modified Mastering Engineering Revision With Pearson Etext -- Access Card Package (14th Edition)
Additional Engineering Textbook Solutions
Mechanics of Materials (10th Edition)
Engineering Mechanics: Statics & Dynamics (14th Edition)
Statics and Mechanics of Materials (5th Edition)
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
Engineering Mechanics: Dynamics (14th Edition)
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
- The inner ring A has an inner radius r1 and outer radius r2. The outer ring B has an inner radius r3 and an outer radius r4, and r2 7 r3. If the outer ring is heated and then fitted over the inner ring, determine the pressure between the two rings when ring B reaches the temperature of the inner ring. The material has a modulus of elasticity of E and a coefficient of thermal expansion of a.arrow_forwardA 50-m steel surveying tape has a mass of 1.6 kg. If the tape is stretched between two points at the same elevation and pulled until the tension at each end is 60 N, determine the horizontal distance between the ends of the tape. Neglect the elongation of the tape due to the tension.arrow_forwardThe cylinder having a diameter 2.5 ft weighs 57 lb and is 6 ft long. Determine the reaction (lb.) at A neglecting friction. Determine the reaction at B (lb.) neglecting friction. Weight density of water is 62.4 lb/ft3 Sp.gr Gs = 1.6arrow_forward
- Determine the magnitude of the reaction in the pin A, the cable BC and the cable that supports the ball with the weight are independent, consider the weight of the ball 247lb and the length of the bar a = 8ft and the angle a = 10 °arrow_forwardDetermine the maximum weight of the bucket that the wire system can support so that no single wire develops a tension exceeding 100 lb.arrow_forwardThe hoist supports an engine of weight W in kg. Determine the force the load creates in member DB and in member FB, which contains the hydraulic cylinder H. Given: X=2 m ; L=3 m ; W= 123 kg.arrow_forward
- The driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800lb and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 kp.arrow_forwardDetermine The Forces P F T Required To Keep The Triangular Frame Inequilibrium.arrow_forwardThe metal strap has a thickness t and width w and is subjected to a temperature gradient T1 to T2 (T1 6 T2). This causes the modulus of elasticity for the material to vary linearly from E1 at the top to a smaller amount E2 at the bottom. As a result, for any vertical position y, measured from the top surface, E = [(E2 - E1)>w]y + E1. Determine the position d where the axial force P must be applied so that the bar stretches uniformly over its cross-section. warrow_forward
- The collar C is fixed to rod AB using a glued bond that allows a maximum force of 405 N parallel to the axis of the rod. The collar has weight W acting in the negative z direction. Determine the weight W in N of the collar that will cause the glued bond to break as shown in figure.arrow_forwardIf the maximum force that any member can support is 8 kN in tension and 6kN in compression, determine the maximum force P that can be supported at joint D.arrow_forwardThe pipe is stuck in the ground so that when it is pulled upward the frictional force along its length varies linearly from zero at B to fmax (force/length) at C. The pipe has a length L, cross-sectional area A, and the material from which it is made has a modulus of elasticity E. Determine the initial force P required to pull the pipe out. Express your answer as an expression in terms of the variables f, L, A and E and any necessary constants.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY