FOX+MCDONALD'S INTRO.TO...-ACCESS+BOX
9th Edition
ISBN: 9781118471340
Author: Pritchard
Publisher: WILEY
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 74P
Glass spheres of 0.1 in. diameter fall at constant velocities of 0.1 and 0.05 ft/s through two different oils of the same specific gravity in very large tanks. If the viscosity of the first oil is 0.002 lbf · s/ft2, what is the viscosity of the second?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
An aluminum sphere of radius 0.5 mm falls through a viscous liquid of density 2700 kg/m3. It attains a constant terminal velocity of 1.5 cm/s. What is the viscosity of the fluid?
a) 0.001 N.s/m2
b) 0.052 N.s/m2
c) 0.25 N.s/m2
d) none of these
At what maximum speed does a compressed air torpedo move, which expells 18 kg of air every second at a speed of 118 m/s? The force of water resistance is proportional to the square of the velocity and is equal to 480 N at a speed of 21 m/s. (The solutiom is 44 m/s)
What are the physical and quantitative evidence of turbulence in fluid flow?
Chapter 9 Solutions
FOX+MCDONALD'S INTRO.TO...-ACCESS+BOX
Ch. 9 - The roof of a minivan is approximated as a...Ch. 9 - A model of a river towboat is to be tested at 1:18...Ch. 9 - For flow over a smooth plate, what approximately...Ch. 9 - A model of a thin streamlined body is placed in a...Ch. 9 - A student is to design an experiment involving...Ch. 9 - A 1 m 2 m sheet of plywood is attached to the...Ch. 9 - The extent of the laminar boundary layer on the...Ch. 9 - Velocity profiles in laminar boundary layers often...Ch. 9 - An approximation for the velocity profile in a...Ch. 9 - Evaluate / for each of the laminar boundary-layer...
Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A fluid, with density = 1.5 slug/ft3, flows at U...Ch. 9 - Solve Problem 9.13 with the velocity profile at...Ch. 9 - Air flows in a horizontal cylindrical duct of...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - Evaluate the displacement thickness and the...Ch. 9 - A laboratory wind tunnel has a test section 25 cm...Ch. 9 - Air flows in the entrance region of a square duct,...Ch. 9 - A flow of 68F air develops in a flat horizontal...Ch. 9 - A flow of air develops in a horizontal cylindrical...Ch. 9 - Using numerical results for the Blasius exact...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - Using numerical results obtained by Blasius (Table...Ch. 9 - A smooth flat plate 2.4 m long and 0.6 m wide is...Ch. 9 - Consider flow of air over a flat plate. On one...Ch. 9 - A thin flat plate, L = 9 in. long and b = 3 ft...Ch. 9 - For a laminar boundary layer on a flat plate,...Ch. 9 - Air at atmospheric pressure and 20C flows over...Ch. 9 - A thin flat plate is installed in a water tunnel...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Assume laminar boundary-layer flow to estimate the...Ch. 9 - Prob. 34PCh. 9 - Water at 10C flows over a flat plate at a speed of...Ch. 9 - Use the momentum integral equation to derive...Ch. 9 - A smooth flat plate 1.6 ft long is immersed in 68F...Ch. 9 - Prob. 38PCh. 9 - A developing boundary layer of standard air on a...Ch. 9 - Assume the flow conditions given in Example 9.3....Ch. 9 - A flat-bottomed barge having a 150 ft 20 ft...Ch. 9 - European InterCity Express trains operate at...Ch. 9 - Grumman Corp. has proposed to build a magnetic...Ch. 9 - Repeat Problem 9.32, for an air flow at 80 ft/s,...Ch. 9 - The velocity profile in a turbulent boundary-layer...Ch. 9 - The U.S. Navy has built the Sea Shadow, which is a...Ch. 9 - The two rectangular smooth flat plates are to have...Ch. 9 - Standard air flows over a horizontal smooth flat...Ch. 9 - Air at standard conditions flows over a flat...Ch. 9 - A uniform flow of standard air at 60 m/s enters a...Ch. 9 - A laboratory wind tunnel has a flexible upper wall...Ch. 9 - Air flows in a cylindrical duct of diameter D = 6...Ch. 9 - Perform a cost-effectiveness analysis on a typical...Ch. 9 - Table 9.1 (on the web) shows the numerical results...Ch. 9 - A fluid flow enters the plane-wall diffuser that...Ch. 9 - For flow over a flat plate with zero pressure...Ch. 9 - A flat-bottomed barge, 80 ft long and 35 ft wide,...Ch. 9 - A towboat for river barges is tested in a towing...Ch. 9 - Plot the local friction coefficient cf, the...Ch. 9 - A smooth plate 3 m long and 0.9 m wide moves...Ch. 9 - Resistance of a barge is to be determined from...Ch. 9 - A nuclear submarine cruises fully submerged at 27...Ch. 9 - You are asked by your college crew to estimate the...Ch. 9 - The drag coefficient of a circular disk when...Ch. 9 - A steel sphere of 0.25 in. diameter has a velocity...Ch. 9 - A steel sphere (SG = 7.8) of 13 mm diameter falls...Ch. 9 - A sheet of plastic material 0.5 in. thick, with...Ch. 9 - As part of the 1976 bicentennial celebration, an...Ch. 9 - What constant speed will be attained by a lead (SG...Ch. 9 - Assuming a critical Reynolds number of 0.1,...Ch. 9 - Glass spheres of 0.1 in. diameter fall at constant...Ch. 9 - A rotary mixer is constructed from two circular...Ch. 9 - Calculate the drag of a smooth sphere of 0.3 m...Ch. 9 - Calculate the drag of a smooth sphere of 0.5 m...Ch. 9 - A cylindrical chimney 0.9 m in diameter and 22.5 m...Ch. 9 - The resistance to motion of a good bicycle on...Ch. 9 - Ballistic data obtained on a firing range show...Ch. 9 - A standard marine torpedo is 0.533 m in diameter...Ch. 9 - A large truck has an essentially boxlike body that...Ch. 9 - At a surprise party for a friend youve tied a...Ch. 9 - A 0.5-m-diameter hollow plastic sphere containing...Ch. 9 - A simple but effective anemometer to measure wind...Ch. 9 - The Willis Tower (formerly the Sears Tower) in...Ch. 9 - It is proposed to build a pyramidal building with...Ch. 9 - Calculate the drag forces on a 1/200 scale model...Ch. 9 - A circular disk is hung in an air stream from a...Ch. 9 - A vehicle is built to try for the land-speed...Ch. 9 - An F-4 aircraft is slowed after landing by dual...Ch. 9 - A tractor-trailer rig has frontal area A = 102 ft2...Ch. 9 - A 180hp sports car of frontal area 1.72 m2, with a...Ch. 9 - An object falls in air down a long vertical chute....Ch. 9 - Prob. 99PCh. 9 - A light plane tows an advertising banner over a...Ch. 9 - The antenna on a car is 10 mm in diameter and 1.8...Ch. 9 - Consider small oil droplets (SG = 0.85) rising in...Ch. 9 - Standard air is drawn into a low-speed wind...Ch. 9 - A small sphere with D = 6 mm is observed to fall...Ch. 9 - A tennis ball with a mass of 57 g and diameter of...Ch. 9 - A water tower consists of a 12-m-diameter sphere...Ch. 9 - A cast-iron 12-pounder cannonball rolls off the...Ch. 9 - A rectangular airfoil of 40 ft span and 6 ft chord...Ch. 9 - A rectangular airfoil of 9 m span and 1.8 m chord...Ch. 9 - Why is it possible to kick a football farther in a...Ch. 9 - If CL = 1.0 and CD = 0.05 for an airfoil, then...Ch. 9 - A wing model of 5 in. chord and 2.5 ft span is...Ch. 9 - A barge weighing 8820 kN that is 10 m wide, 30 m...Ch. 9 - A spherical sonar transducer with 15 in. diameter...Ch. 9 - While walking across campus one windy day, an...Ch. 9 - If the mean velocity adjacent to the top of a wing...Ch. 9 - The NACA 23015 airfoil is to move at 180 mph...Ch. 9 - A human-powered aircraft has a gross weight of 240...Ch. 9 - WiffleTM balls made from light plastic with...Ch. 9 - A model airfoil of chord 6 in. and span 30 in. is...Ch. 9 - An antique airplane carries 50 m of external guy...Ch. 9 - How do cab-mounted wind deflectors for...Ch. 9 - An airplane with an effective lift area of 25 m2...Ch. 9 - The U.S. Air Force F-16 fighter aircraft has wing...Ch. 9 - A light airplane, with mass M = 1000 kg, has a...Ch. 9 - A light airplane has 35-ft effective wingspan and...Ch. 9 - Assume the Boeing 727 aircraft has wings with NACA...Ch. 9 - Jim Halls Chaparral 2F sports-racing cars in the...Ch. 9 - Some cars come with a spoiler, a wing section...Ch. 9 - Roadside signs tend to oscillate in a twisting...Ch. 9 - Air moving over an automobile is accelerated to...Ch. 9 - A class demonstration showed that lift is present...Ch. 9 - Rotating cylinders were proposed as a means of...Ch. 9 - A baseball pitcher throws a ball at 80 mph. Home...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
Air motion can be good or bad, depending on the air temperature. Discuss the general effect of increased or dec...
Heating Ventilating and Air Conditioning: Analysis and Design
Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 8kN.
Mechanics of Materials (10th Edition)
1.1 What is the difference between an atom and a molecule? A molecule and a crystal?
Manufacturing Engineering & Technology
Construct the a s graph for the same interval.
Engineering Mechanics: Dynamics (14th Edition)
9.17 Compute the total elongation of a steel bar, originally 25 in. long, if the induced tensile stress is 15,0...
Applied Statics and Strength of Materials (6th Edition)
Comprehension Check 8-8
The temperature of dry ice is −109.3 degrees Fahrenheit [°F]. Convert this temperature ...
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Express Newton’s first, second, and third laws.arrow_forwardWhich quantities are physical phenomena associated with fluid flow over bodies? I. Drag force acting on automobiles II. The lift developed by airplane wings III. Upward draft of rain and snow IV. Power generated by wind turbines (a) I and II (b) I and III (c) II and III (d ) I, II, and III (e) I, II, III, and IVarrow_forwardAs a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.arrow_forward
- A pipe has a cross-sectional area of 16.5cm2 at point A, where the speed of the fluid (water) is 1.2 m/s and the pressure is 2.00 atm. The pipe ascends 3.00 m and narrows to 8.20 cm2 at point C. a) what's the speed of the fluid at point C. b) what's the absolute pressure at point C.arrow_forwardA sea-level automobile tire is initially at 32 lbf/in2 gagepressure and 75 °F. When it is punctured with a hole that resemblesa converging nozzle, its pressure drops to 15 lbf/in2gage in 12 min. Estimate the size of the hole, in thousandthsof an inch. The tire volume is 2.5 ft2.arrow_forwardA sled with two runners slides along a thin horizontal layer of water between the ice and the runners. The horizontal force that the water puts on the runners is equal to 2.4 lb when the sled's speed is 50 ft/s. The total area of both runners in contact with the water is 0.04 ft2, and the viscosity of the water is 3.5x10 lbs/ft2. Determine the thickness of the water layer under the runners. Assume a linear velocity distribution in the water layer.arrow_forward
- Water with density of 1000 kg/m^3 flows through a horizontal pipe (in the x-z plane) bend as shown. The weight of the pipe is 350 N and the pipe cross-sectional area is constant and equals to 0.35 m^2. The magnitude of the inlet velocity is 4 m/s. The absolute pressures at the entrance and exit of the bend are 210 kPa and 110 kPa, respectively. Assuming the atmospheric pressure is 100 kPa and neglecting the weight and viscosity of the water , find the following: A)The force (in the x-axis direction) acting on the fluid? B)The force (in the z-axis direction) acting on the pipe? C)The reaction force in the y direction ?arrow_forwardWater with density of 1000 kg/m^3 flows through a horizontal pipe (in the x-z plane) bend as shown. The weight of the pipe is 350 N and the pipe cross-sectional area is constant and equals to 0.35 m^2. The magnitude of the inlet velocity is 4 m/s. The absolute pressures at the entrance and exit of the bend are 210 kPa and 110 kPa, respectively. Assuming the atmospheric pressure is 100 kPa and neglecting the weight and viscosity of the water , find the following: A)If the area of section 2 is doubled, then the velocity will be halved but the momentum flux will still be the same: ture or false ?arrow_forwardWater with density of 1000 kg/m^3 flows through a horizontal pipe (in the x-z plane) bend as shown. The weight of the pipe is 350 N and the pipe cross-sectional area is constant and equals to 0.35 m^2. The magnitude of the inlet velocity is 4 m/s. The absolute pressures at the entrance and exit of the bend are 210 kPa and 110 kPa, respectively. Assuming the atmospheric pressure is 100 kPa and neglecting the weight and viscosity of the water , find the following:arrow_forward
- Water is flowing in a 3-cm-diameter garden hose at a rate of 25 L/min. A 20-cm nozzle is attached to the hose which decreases the diameter to 1.2 cm. The magnitude of the acceleration of a fluid particle moving down the centerline of the nozzle is (a) 9.81 m/s2 (b) 17.3 m/s2 (c) 28.6 m/s2 (d ) 33.1 m/s2 (e) 42.4 m/s2arrow_forwardA 10-in diameter plunger slides in a 10.006-in diameter cylinder, the annular space being filled with oil having a kinematic viscosity of 0.004 ft²/s and specific gravity of 0.85. If the plunger moves at 0.6 ft/s, find the frictional resistance when 9ft is engaged in the cylinder.arrow_forwardA block of mass m slides along a horizontal surface lubricated with a thick oil which providesa drag force proportional to the square root of velocity.F_d=-bv^1/2If v = v0 at t = 0, determine v as a function of timearrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Properties of Fluids: The Basics; Author: Swanson Flo;https://www.youtube.com/watch?v=TgD3nEO1iCA;License: Standard YouTube License, CC-BY
Fluid Mechanics-Lecture-1_Introduction & Basic Concepts; Author: OOkul - UPSC & SSC Exams;https://www.youtube.com/watch?v=6bZodDnmE0o;License: Standard Youtube License