Concept explainers
(a)
The tension in the wire.
Answer to Problem 77QAP
The tension in the wire is
Explanation of Solution
Given:
Mass of the beam
Let 'T' be the tension in the wire
Length of beam
Formula used:
Newton's 2nd law:
Torque (or moment of force)
Here, all alphabets are in their usual meanings.
Calculation: Pictorial Diagram
Consider the pictorial diagram wherein all components are shown
Apply Newton's 2nd law
For x − component:
For y − component:
Net Torque at the hinge
Therefore,
Hence, the tension in the wire is
Conclusion:
Thus, the tension in the wire is
(b)
The minimum cross-sectional area of the wire.
Answer to Problem 77QAP
The minimum cross-sectional area of the wire is
Explanation of Solution
Given:
Ultimate breaking strength
Let the minimum cross-sectional area of the wire be ' A'
Maximum applied force on the wire
Formula used:
Ultimate strength
Here, all alphabets are in their usual meanings.
Calculation:
Substituting the given values in above formula,
Hence, the minimum cross-sectional area of the wire is
Conclusion:
Thus, the minimum cross-sectional area of the wire is
Want to see more full solutions like this?
Chapter 9 Solutions
COLLEGE PHYSICS-ACHIEVE AC (1-TERM)
- In Figure 9.21, the cg of the pole held by the pole vaulter is 2.00 m from the left hand, and the hands are 0.700 m apart. Calculate the force exerted by (a) his right hand and (b) his left hand. (c) If each hand supports half the weight of the pole in Figure 9.19, show that the second condition for equilibrium (net =0 ) is satisfied for a pivot other than the one located at the center of gravity of the pole. Explicitly show how you follow the steps in the Problem-Solving Strategy for static equilibrium described above. Figure 9.21 A pole vaulter is holding a pole horizontally with both hands. The center of gravity is to the left side of the vaulter.arrow_forwardA horizontal plank 4.00 m long and having mass 20.0 kg rests on two pivots, one at the left end and a second 1.00 m from the right end. Find the magnitude of the force exerted on the plank by the second pivot. (See Section 8.4.)arrow_forwardIn the What If? section of Example 12.2, let d represent the distance in meters between the person and the hinge at the left end of the beam. (a) Show that the cable tension is given by T = 93.9d + 125, with T in newtons. (b) Show that the direction angle of the hinge force is described by tan=(323d+41)tan53.0 (c) Show that the magnitude of the hinge force is given by R=8.82103d29.65104d+4.96105 (d) Describe how the changes in T, , and R as d increases differ from one another.arrow_forward
- Two uniform planks, each of mass m = 7.45 kg and length L = 2.51 m, are connected by a hinge at the top and by a chain of negligible mass attached at their centers, as shown in the figure. The assembly will stand upright, in the shape of an A, on a frictionless surface without collapsing. If the chain has the length 0.81 m, find each of the following: a) the absolute value of the tension in the chain, b) the absolute magnitude of the force on the hinge of each p lankarrow_forwardA uniform beam of length L = 11.7 meters and mass of 109.3 kg is pinned at one end and is being supported by a wire as shown. The wire is connected to the beam x = 3.3 meters from the pin. A person of mass 81.6 kg is standing all the way out on the edge of the beam. If θ = 17.3 degrees and φ = 79.4 degrees, what is the tension in the wire?arrow_forwardA uniform plank of length 5.0 m and weight 225 N rests horizontally on two supports, with 1.1m of the plank hanging over the right support. To what distance x can a person who weighs 377 N walk on the overhanging part of the plank before it just begins to tip?arrow_forward
- Physics for Scientists and EngineersPhysicsISBN:9781337553278Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers with Modern ...PhysicsISBN:9781337553292Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
- Glencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-HillPhysics for Scientists and Engineers, Technology ...PhysicsISBN:9781305116399Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningCollege PhysicsPhysicsISBN:9781285737027Author:Raymond A. Serway, Chris VuillePublisher:Cengage Learning