Consider an infinitely thin flat plate at an angle of attack
Want to see the full answer?
Check out a sample textbook solutionChapter 9 Solutions
FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
Additional Engineering Textbook Solutions
Thinking Like an Engineer: An Active Learning Approach (4th Edition)
Vector Mechanics for Engineers: Statics and Dynamics
Fluid Mechanics: Fundamentals and Applications
Applied Statics and Strength of Materials (6th Edition)
Statics and Mechanics of Materials (5th Edition)
Fluid Mechanics Fundamentals And Applications
- Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance to the point at which the hydrodynamic boundary layers meet.arrow_forwardConsider a flat plate at zero angle of attack in a hypersonic flow at Mach10 at standard sea level conditions. At a point 0.5 m downstream from theleading edge, the local shear stress at the wall is 282 N/m2. The gastemperature at the wall is equal to standard sea level temperature. At thispoint, calculate the velocity gradient at the wall normal to the wall.arrow_forward1. A flat plate airfoil with a chord length of 1 m and a width of 6 m is required to generate a lift of 40, 000 N when flying in air at a Mach number of 2.0, a temperature of −20°C and a pressure of 105 P a. What is the required angle of attack? What is the wave drag at this angle of attack? 2. A symmetrical diamond-shaped airfoil is placed at an angle of attack of 2° in a flow at Mach 2 and static pressure of 2×103 P a. The half-angle at the leading and trailing edges is 3° . If its total surface area (top and bottom) is 4 m2 , find the forces due to lift and wave drag acting on the airfoil.arrow_forward
- SR-71 Blackbird cruised at Mach 3.2 at 80,000 ft altitude. However, it was designed to leak a finite amount of fuel during takeoff because the surface temperature of the aircraft increases (which leads to expansion of the surfaces) due to aerodynamic heating during flight. Estimate the flow temperature around the aircraft during cruise condition. Assume specific heat ratio is 1.4.arrow_forward7. Using shock-expansion theory, calculate the lift and drag coefficients for a flat plate at a 5° angle of attack in a Mach 2.4 flow. Pa M, P3arrow_forwardConsider Mach 4 flow at standard sea level conditions over a flat plateof chord 5 in. Assuming all laminar flow and adiabatic wall conditions,calculate the skin-friction drag on the plate per unit span.arrow_forward
- Calculate the lift and drag coefficiens for a flat plate at a 5◦ angle of attack in a Mach 3 flow.arrow_forwardStarting from the basic principles, drive an expression to compute the lift coefficient when the free stream Mach number equals (0.8)arrow_forwardThe stagnation pressure in a Mach 2 wind tunnel operating with air is 750 kPa. A 4-cm-diameter sphere positioned in the wind tunnel has a drag coefficient of 0.95. Calculate the drag force on the sphere. FD Narrow_forward
- Pu Wings at supersonic flows can be modeled as a flat plate that have constant pressure distributions across their chord. Ignoring any viscous effects determine the drag force of the wing section. Round to the full N/m and make sure you use the standard sign convention (i.e. right hand rule). Use the following data chord = 1.5 m epsilon = 5 degree angle of attack = 20.0 alpha upper surface pressure = 60,000 Pa lower surface pressure = 150,000 Paarrow_forwardConsider a flat plate at α = 20◦ in a Mach 20 freestream. Using straightnewtonian theory, calculate the lift- and wave-drag coefficients. Comparethese results with exact shock-expansion theory.arrow_forwardThe lift curve for the 4 digit NACA 2421 airfoil is shown in the Figure. Consider a wing with AR = 8, sweep ? = 15 ???, and airplane flies at the Mach number equal to 0.3. The Oswald efficiency span number ?1 = 0.95 Calculate the lift slope for the finite wing. Clearly show the formula and explanations in the solution.arrow_forward
- Principles of Heat Transfer (Activate Learning wi...Mechanical EngineeringISBN:9781305387102Author:Kreith, Frank; Manglik, Raj M.Publisher:Cengage Learning