Consider an oblique shock wave with a wave angle of
a.
b.
Want to see the full answer?
Check out a sample textbook solutionChapter 9 Solutions
FUND OF AERODYNAMICS(LLF) +CONNECT (1YR)
Additional Engineering Textbook Solutions
Fox and McDonald's Introduction to Fluid Mechanics
Thermodynamics: An Engineering Approach
Fundamentals Of Thermodynamics
Shigley's Mechanical Engineering Design (McGraw-Hill Series in Mechanical Engineering)
Statics and Mechanics of Materials
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
- The flow just upstream of a normal shock wave is given byp1 = 1800 lb/ft2, T1 = 480 ◦R, and M1 = 3.1. Calculate the velocity andM∗ behind the shock.arrow_forwardd*, 2. Consider a normal shock wave in air where the upstream flow properties are u1 = 690 m/s, T1 = 288 K, and p1=1 atm. Calculate the velocity, temperature, and pressure downstream of the shock.arrow_forwardThe entropy change across a normal shock wave (Tox= 505 K, vx= 490 ms-1)arrow_forward
- A normal shock wave propagates into atmosphere where the atmospheric temperature is equal 336K and pressure is 0.8 atm. For a given pressure ratio of p2/p₁ 41 to T₁ = a) Assuming stationary atmosphere, calculate the shock wave velocity and the velocity induced behind the shock wave. Also calculate the temperature, total pressure and total temperature of the fluid particles behind the shock wave using equations for moving normal shock. =arrow_forwardThe driver and driven gases in a shock tube are both air at 300 K. Assume p4/p1 = 8.006. After the diaphragm is broken, an incident shock wave is propagating into the driven section and an incident expansion wave is propagating into the driver section. If the strength of the incident shock (p2/p1) is 2.6, a. Calculate the strength of the incident expansion wave (p3/p4). b. Calculate the induced mass motion velocity behind the expansion wave. c. Find the propagation velocity of the head expansion wave. d. Find the propagation velocity of the tail expansion wave.arrow_forward5. Airflow at Mach 2 passes through an oblique shock as shown and deflects 10°. A second oblique shock reflects from the solid wall. What is the pressure ratio (p3/p₁) across the two-shock system? Assume that there is no boundary layer near the wall, so the flow is uniform in each of the regions bounded by the shocks and that y = 1.4. Reflected oblique shock 10° M=2arrow_forward
- 30. A normal shock wave across which the pressure ratio is 1.25 is propagating down a duct containing still air at a pressure of 120 kPa and a temperature of 35°C. This shock wave is reflected off the closed end of the duct. Find the pressure and tem- perature behind the reflected shock wave.arrow_forwardThe flow just upstream of a normal shock wave is given by p1 = 1 atm,T1 = 288 K, and M1 = 2.6. Calculate the following properties justdownstream of the shock: p2, T2, ρ2, M2, p0,2, T0,2, and the change inentropy across the shock.arrow_forwardThe velocity of flow after a normal shock wave when (Tx= 315 K, vx= 555 ms-1)arrow_forward
- = 1-An oblique shock forms in air at an angle of 0 30°. Before passing through the shock, the air has a temperature of 60°F, a pressure of 10 psia, and is traveling at M = 2.6. elocity components before and after (a) Compute the normal and tangential the shock. HEGE Of and (b) Determine the temperature and pressure after the shock. (c) What is the deflection angle?arrow_forwardIncompressible air (density=1.2 kg/m3) flows around the car, if the pressure coefficient at point A is Cp= -6.6 and the reference dynamic pressure is 20 kpa, then what is the velocity of air at point A? Vo, Po 09arrow_forwardGood day. Here is my question (10) Consider a low-speed subsonic wind tunnel with a 12/1 contraction area ratio for the nozzle. If the flow in the test section is at a standard sea level conditions with a velocity of 50 m /s, calculate the height difference in a U-tube mercury manometer with one side connected to the nozzle inlet and the other to the test section. ρHg = 13.6 x 103 kg/ m^3.arrow_forward
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY