Applied Fluid Mechanics (7th Edition)
7th Edition
ISBN: 9780132558921
Author: Robert L. Mott, Joseph A. Untener
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 9.33PP
A heat sink for an electronic circuit is made by machining a pocket into a block of aluminum and then covering it with a flat plate to provide a passage for cooling water as shown in Fig.
9.22. Compute the Reynolds number if the flow of water at
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
Derive an expression for time of emptying a tank through a pipe at its bottom,accounting for major and minor losses
Calculate the minimum velocity of flow in ft/s of water at 160°F in a 2-in steel tube with a wall thickness of 0.065 in for which the flow is turbulent.
A pipe 12 mm diameter with a velocity of 0.50 m/s is attached by a nozzle at the end having a diameter of 3 mm diameter. Find the velocity of the water in the nozzle in m/s.
Chapter 9 Solutions
Applied Fluid Mechanics (7th Edition)
Ch. 9 - Compute points on the velocity profile from the...Ch. 9 - s9.2 Compute points on the velocity profile from...Ch. 9 - Compute points on the velocity profile from the...Ch. 9 - Compute points on the velocity profile from the...Ch. 9 - A small velocity probe is to be inserted through a...Ch. 9 - If the accuracy of positioning the probe described...Ch. 9 - An alternative scheme for using the velocity probe...Ch. 9 - Prob. 9.8PPCh. 9 - For the flow of 12.9L/min of water at 75C in a...Ch. 9 - A large pipeline with a 1,200m inside diameter...
Ch. 9 - Prob. 9.11PPCh. 9 - Prob. 9.12PPCh. 9 - Prob. 9.13PPCh. 9 - Prob. 9.14PPCh. 9 - Using Eq. (9-4), compute the ratio of the average...Ch. 9 - Prob. 9.16PPCh. 9 - Repeat Problem 9.16 for the same conditions,...Ch. 9 - Prob. 9.18PPCh. 9 - A shell-and-tube heat exchanger is made of two...Ch. 9 - Figure 9.14 shows a heat exchanger in which each...Ch. 9 - Figure 9.15 shows the cross section of a...Ch. 9 - Air with a specific weight of 12.5N/m3 and a...Ch. 9 - Carbon dioxide with a specific weight of...Ch. 9 - Water at 90F flows in the space between 6 in...Ch. 9 - Refer to the shell-and-tube heat exchanger shown...Ch. 9 - Refer to Fig. 9.14, which shows two DN 150...Ch. 9 - Refer to Fig. 9.15, which shows three pipes inside...Ch. 9 - Water at 10C is flowing in the shell shown in Fig....Ch. 9 - Figure 9.19 shows the cross section of a heat...Ch. 9 - Figure 9.20 shows a liquid-to-air heat exchanger...Ch. 9 - Glycerin ( sg=1.26 ) at 40C flows in the portion...Ch. 9 - Each of the square tubes shown in Fig. 9.21...Ch. 9 - A heat sink for an electronic circuit is made by...Ch. 9 - Figure 9.23 shows the cross section of a cooling...Ch. 9 - Prob. 9.35PPCh. 9 - The blade of a gas turbine engine contains...Ch. 9 - For the system described in Problem 9.24. compute...Ch. 9 - For the shell-and-tube heat exchanger described in...Ch. 9 - For the system described in Problem 9.26 compute...Ch. 9 - For the system described in Problem 9.27 compute...Ch. 9 - For the shell-and-tube heat exchanger described in...Ch. 9 - For the heat exchanger described in Problem 9.29...Ch. 9 - For the glycerin described in Problem 9.31 compute...Ch. 9 - For the flow of water in the square tubes...Ch. 9 - If the heat sink described in Problem 9.33 is 105...Ch. 9 - Compute the energy loss for the flow of water in...Ch. 9 - In Fig. 9.26 ethylene glycol ( sg=1.10 ) at 77F...Ch. 9 - Figure 9.27 shows a duct in which methyl alcohol...Ch. 9 - Prob. 9.49PPCh. 9 - Figure 9.29 shows a system in which methyl alcohol...Ch. 9 - A simple heat exchanger is made by welding...Ch. 9 - Three surfaces of an instrument package are cooled...Ch. 9 - Figure 9.32 shows a heat exchanger with internal...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A pipe handles a flow rate of 0.002 m³/s. Find the minimum inside diameter that will provide an average fluid velocity not to exceed 6.1 m/s.arrow_forwardA ventilation duct in a large industrial warehouse measures 1067 mm * 1524 mm. Compute the circular equivalent diameter. Then determine the maximum flow rate of air that the duct could carry while limiting the friction loss to 0.82 Pa/marrow_forwardThe flow rate of air moving through a square 0.50-m by 0.50-m duct is 160 m3/min. What is the mean velocity of the air in m/s?arrow_forward
- A needle with a piston is used to extract blood from the arm of a patient. Solve for the ave. speed of the blood flow, in mm/s, in the needle if the radius of the piston is 2.5mm and the diameter of the needle is 0.5mm and length of 10mm. Take into account the blood withdrawing speed of 6mm/s and air leaks around the piston at 20mm3/s.arrow_forwarda. Solve for the two (2) atmospheric condition, Pn1 & Pn2 at 32.68 0C and 41.12 °C. b. Calculate the diameter of the pipe at suction side if the velocity of air flow is 22.82 m/s with flow rate of 2.96 m³ /second. c. Compute the velocity head at suction side if the velocity is 33.68 m/sec.arrow_forwardA pipe with a 16 in. diameter carries water having a velocity of 3 ft/s. What is the discharge in cfs and in gpm?arrow_forward
- Need detailed solution. 4 decimal places. A fluid is flowing in a 6 in diameter pipe at a pressure of 4 psi with a velocity of 8 ft/s. The elevation of the center of the pipe above a given datum is 10 ft. Find the total energy head above the given datum in meters if the fluid is (a) water, (b) oil with specific gravity of 0.85, (c) gas with specific weight of 0.42 lb/ft^3arrow_forwardA certain liquid has an SG of 1.34 and flows through a 7-in diameter tube at 1.9 ft/s. Calculate the flow in slug/s.arrow_forwardA submersible pump of 80 percent efficiency is used in pumping water with flow rate,Q from a river to a pool at an elevation, h. The frictional losses is assumed with losscoefficient, K = 10. By the aid of a labelled diagram, derive an expression on thepower require to drive the pump.arrow_forward
- An ammonia compressor has a 5 percent clearance volume and a displacement rate of 80'L/s and pumps against a condensing temperature of 40 C. For the two different evaporating temperatures of -10 and 10 C, compute the refrigerant flow rate assuming that the clearance volumetric efficiency applies.arrow_forwardThe volume flow rate of water is 662,73 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C)arrow_forwardOil flow through a 16 tubes on a single cooler with a velocity of 2 m/s. The internal diameter of the tube is 30mm and oil density is 0.85 gm/ml. Find the volume flow in liters per sec.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Intro to Compressible Flows — Lesson 1; Author: Ansys Learning;https://www.youtube.com/watch?v=OgR6j8TzA5Y;License: Standard Youtube License