Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840728
Author: Limbrunner
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 9, Problem 9.9P
A No. 32 (metric designation) reinforcing bar for concrete has a diameter of 32 mm. The baris cut to length in a shear apparatus as shown. The required force P for the shearing operation is300 kN. Determine the ultimate shear strengthT(ult) for this bar.
Expert Solution & Answer
Learn your wayIncludes step-by-step video
schedule03:02
Students have asked these similar questions
What is the shearing stress developed at the neutral axis of the beam with a circular cross section having a diameter of 18 mm and a shear force V = 25 kN. Assume that the shearing stress is uniformly distributed across the neutral axis. Answer must be in MPa.
A5-mm thick plate of steel is formed into the cross section shown in Fig. P&.13. Locate the shear center for the cross section.
Derive the formula for the maximum shearing stress due to bending if the the cross section is a criclewith radius r and shear force V.
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
ICA 7-1
Express the following values using scientific notation, engineering notation, and using an appropriate ...
Thinking Like an Engineer: An Active Learning Approach (3rd Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, and Service (5th Edition)
In each case, determine the moment of the force about point O. Prob. P3-1
Statics and Mechanics of Materials (5th Edition)
What parts are included in the vehicle chassis?
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
If the acceleration is 2.5 m/s2, determine the altitude h. Assume the earths diameter to be 12 713 km.
Engineering Mechanics: Dynamics (14th Edition)
Determine the internal normal force between lettered points on the cable and rod. Draw all necessary free-body ...
Mechanics of Materials (10th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- At a given 7 locations/sections (0,1,2,3,4,5,6) on a beam of uniform I-section, the beam is subjected to a shear force of 100 kN. Plot a curve to show the variation of shear stress across the section and hence determine the ratio of the maximum shear stress to the mean shear stress given as;arrow_forward5.1 A uniform l-section beam has flanges 150 mm wide by 8 mm thick and a web 180 mm wide and 8 mm thick. At a certain section, there is a shearing force of 120 kN. Draw a diagram to illustrate the distribution of shear stress across the section as a result of bending. What is the maximum shear stress?arrow_forwardThe channel section shown below is simply supported over a span of 5 m and carries a uniformly distributed load of 15 kN/m run over its whole length. Find shearing-stress distribution diagram at the point of maximum shearing force and mark important values. Determine the ratio of the maximum shearing stress to the average shearing stress.arrow_forward
- A T- section is the cross section of a loaded beam as shown.Given: U1= 20 kN/m; M1 = 100 kN-m; P1 = 120 kN a.) Draw the shear diagram using graphical solutionb.) Determine maximum shearing stress.b.) Determine the shearing stress at the junction of the T-section.arrow_forwardQuestion 2 Shear Stress AT shaped beam is fabricated from two sections of timber nailed together as shown below. If the section is subjected to a shearing force of 5 kN, calculate the shear stress at the level of the neutral axis and at the level just below the junction of the two pieces of timber. 150 mm 50 mm 200 mm 50 mmarrow_forwardA loaded beam, 60 mm wide by 100 mm high and 6 m long, has the shear and moment diagrams as shown below. Determine (a) the magnitude, type and location of the maximum flexural stress (in MPa) (b) the stress (specify the type) in a fiber 30 mm from the top of the beam at a section 3.5 m from the left end. I = bh3/12arrow_forward
- A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm diameter steel bolts must be used on a 200-mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?arrow_forwardA flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm in outside and 94 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 63 MPa, how many 10-mm-diameter steel bolts must be used on a 190-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft?arrow_forwardA timber beam, 80mm wide by 60mm high, is subjected to a vertical shear load of V = 40KN. Determine the shearing stress developed at layers 20mm apart from top to bottom of the section. pls answer with complete solution thank youarrow_forward
- A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?arrow_forwardThe maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?arrow_forwardWhat must be the maximum torque of a 5mm diameter aluminum wire so that it can be twisted through 1 complete revolution without exceeding a shear of 42N/mm2. Take, G=27 GPa.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About TRANSVERSE SHEAR in 10 Minutes!! - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=4x0E9yvzfCM;License: Standard Youtube License