![Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)](https://www.bartleby.com/isbn_cover_images/9780134009087/9780134009087_largeCoverImage.gif)
Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
5th Edition
ISBN: 9780134009087
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 9, Problem 9CQ
Which type of pliers is capable of fitting over a large object?
a. Slip-joint pliers
b. Linesman’s pliers
c. Locking pliers
d. Multigroove adjustable pliers
Expert Solution & Answer
![Check Mark](/static/check-mark.png)
Want to see the full answer?
Check out a sample textbook solution![Blurred answer](/static/blurred-answer.jpg)
Students have asked these similar questions
What are the following:
1. Simple support
2. Roller support
3. Hinged pin support
4. Fixed support
It is a small tool that features the standard angle (600) for lathe centers and for threading tool for American National Standard screw threads.
a. Gauge Block
b. Feeler Gauge
c. Center Gauge
d. Screw-Pitch Gauge
What is the point at which a machine has a tendency to grab a body part?
a. Grip point
b. Point of operation
c. Point of contact
d. Nip point
Chapter 9 Solutions
Automotive Technology: Principles, Diagnosis, and Service Plus MyLab Automotive with Pearson eText -- Access Card Package (5th Edition) (Automotive Comprehensive Books)
Ch. 9 - Why are wrenches offset 15 degrees?Ch. 9 - What are the other names for a line wrench?Ch. 9 - What are the standard automotive drive sizes for...Ch. 9 - Which type of screwdriver requires the use of a...Ch. 9 - What is inside a dead-blow hammer?Ch. 9 - Prob. 6RQCh. 9 - When working with hand tools, always _____. a....Ch. 9 - Prob. 2CQCh. 9 - Prob. 3CQCh. 9 - Prob. 4CQ
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- List four different types of pliers.arrow_forwardList the four basic pieces of a step clamp set: a. ______________ b. ______________ c. _____________ d. _____________arrow_forwardTo fix a machine on the ground, we can use Select one: O a. Splines and Colts O b. Studs & Thread inserts O . Bolts & Nuts O d. Keys & Keywaysarrow_forward
- Differentiate between a fast and loose pulley.arrow_forwardThe safety equipment used for disassembly of 4 jaw chuck is a. Safety goggles b. Gloves C. Ear plugs d. Helmetarrow_forward1) The working face of ordinary flat key is 1 A. Side C. Bottom surface D. End face B. Upper top surface 2)When the rotating shaft works, it mainly bears_ A. Pure torque C. Torque and bending moment .B. Pure bending moment D. Friction torque 3) Section angle of V-belt in belt drive q-40°,In order to make good contact and increase friction, the pulley groove angle should be A.Slightly greater than 40° C.Equal to 40 B.Slightly less than 40" .D.Equal to 90°arrow_forward
- width of heavy-single plyarrow_forward13. When tightened, dry seal threads A. are crushed to make a leakproof seal. B. compress an O-ring to prevent leaks. C. can be easily loosened and tightened again. D. make a 45-degree flare in the tubing.arrow_forwardWhich of the following is the correct order of doing a fitting job? B. Clamping on vice- Marking -Filing -Surface finishing C. Marking -Filing - Surface finishing- Clamping on vice D. Marking - Clamping on vice -Filing - Surface finishing A. Surface finishing-Clamping on vice-Filing-Markingarrow_forward
- Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.arrow_forwarddifferentiate between shaper and planer machine any six differencearrow_forwardWhich of the following is the correct order of doing a fitting job? C. Marking -Filing - Surface finishing- Clamping on vice B. Clamping on vice- Marking -Filing -Surface finishing A. Surface finishing-Clamping on vice-Filing-Marking D. Marking - Clamping on vice -Filing - Surface finishingarrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781305578296/9781305578296_smallCoverImage.gif)
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
![Text book image](https://www.bartleby.com/isbn_cover_images/9781285444543/9781285444543_smallCoverImage.gif)
Precision Machining Technology (MindTap Course Li...
Mechanical Engineering
ISBN:9781285444543
Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes
Publisher:Cengage Learning
HOME SHOP JIGS & FIXTURES PART 1, TYPES OF JIGS & ACCESSORIES AND THE THEORIE BEHIND THE TOOLS; Author: THATLAZYMACHINIST;https://www.youtube.com/watch?v=EXYqi42JimI;License: Standard Youtube License