3. A mixer containing 100 gal of Na,SO4 solution (4 lbs of Na;S04 per gal) is attached to a reservoir containing a solution of 1 Ib of Na,SO4/gal. If the solution is pumped from the reservoir at the rate of 5 gal/min and the mixed solution runs out of the mixer at the rate of 5 gal/min, how long will it take to reduce the concentration of salt in the tank to 1/2 its original value?

3. A mixer containing 100 gal of Na,SO4 solution (4 lbs of Na;S04 per gal) is attached to a reservoir containing a solution of 1 Ib of Na,SO4/gal. If the solution is pumped from the reservoir at the rate of 5 gal/min and the mixed solution runs out of the mixer at the rate of 5 gal/min, how long will it take to reduce the concentration of salt in the tank to 1/2 its original value?

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter11: Solutions

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

A 1.458 g primary-standard grade Na2CO3 (MW = 105.99 g/mol) was used to standardize an HCl solution. Solve for the molarity of HCl if 24.81 mL of HCl was used to reach the endpoint.
A 25mL volumetric pipet is used to deliver a sample of the stock solution marked “0.6000M X2SO4” into a 100mL volumetric flask. Distilled water is added to the flask until it is about 3/4thfull, the solution is mixed well, then more water is added to fill it up to the calibration mark, then it is mixed again. Calculate the concentration of X+ion in the dilute solution made above.
A local company sent you their green alternative for window cleaner to be tested for percent (w/v) acetic acid content. For your experiment, you first standardized your NaOH titrant with 0.8053 g of (99.80 % purity) KHP. You used 40.60 mL of NaOH for your standardization. After that you then analyzed a 10.00 mL sample and found that you needed 43.20 mL NaOH to reach the end point. Summary of results: Standardization Sample analysis KHP Weight (g) 0.8053 g Volume of sample 50.00 mL Purity 99.80% NaOH (mL) used 33.20 mL NaOH (mL) used 40.60 mL Determine the following: Molarity of NaOH % (w/v) acetic acid
30.0 mL of 0.400 M Zn²⁺ is mixed with 100.0 mL of 0.200 M F⁻ (Ksp ZnF₂ = 0.030). In the mixture you would observe
5) 15.00 mL of 0.620 M potassium chloride solution is combined with 25.00 ML of 0.870 M potassium phosphate solution. What is the concentration of potassium ions in the final solution (in M)? b) I would ask you to perform a Material Balance on the mixing - find all concentrations ( of all ions ) and the mass of the PPT.
1. A 0.57 gram sample aspirin (MM=180 g/mol) is crushed and dissolved in water. The sample is titrated with 0.20 M sodium hydroxide. The titration required an average volume of 8.50 ml of sodium hydroxide to reach the endpoint. What is the purity of the sample? 2. Nitrosyl chloride, NOCl, dissociates on heating as shown below. When a 1.50 gram sample of pure NOCl is heated at 350 oC in a volume of 1.00 liter, the percent dissociation is found to be 57.2%. What is the quilibbrium constant? NOCl <-> NO + 1/2 CL2
How much alum product would be lost to the recrystallization solution if you had 42.5 mL of solution after filtration and the solubility of alum is approximately 2.62 g alum in 100. mL of 0oC acidic water?
*** CALULATE FINL CONCENTRATION USING 2 IG FIGS AND APPROPRIATE UNITS A 6.0 mLmsample of a 50.0 % (mm/vv) acetic acid (HC2H3O2) solution is added to water to give a final volume of 34 mL.
Consider a 1.000-L stock solution of 9.69 M Na3PO4. A 2.000-mL aliquot is taken from this stock solution and diluted to a final volume of 1.000 L. A 5.000-mL aliquot is then taken from this new solution and further diluted to make a new solution with a final volume of 750.0 mL. Calculate Na+ in the final solution.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. From the stock solution (0.020 M), pipet 4.00 mL and dilute to 100.00 mL. From the diluted solution, pipet 0.00, 1.00, 1.50, 2.00, 2.50, 5.00 and 7.50 mL aliquots into 100 mL volumetric flasks. Dilute to mark. Determine the concentration of each standard solution and tabulate.
500 mL of pure water is first added to 500 mL of 0.500 M K2Cr2O7, making a “standard” solution. What volume of the “standard” solution, when diluted to 500 mL, will be needed to produce another “standard” solution of 0.100 M K2Cr2O7?
Prepare 0.1 M solutions of NaOH and 0.1 M ethyl acetate using high-purity distilled water. So, weight desired amount of NaOH and ethyl acetate and dissolved in dH2O to prepare stock solution in equal molarity. Mw (NaOH) = 40.0 g/mol , Mw (EtOAc)= 88.1 g/mol, Density(EtOAc): 0.898 g/cm3