A commercial vinegar is analyzed for the percent acetic acid present. The data for the first trial is given below. Calculate the required quantities using the raw data below. Preparation of Vinegar Sample: • Mass of vinegar (g) = 3.06 Analysis of Vinegar Sample: • Buret reading, initial (mL) = 25.40 • Buret reading, final (mL) = 3.70 • Molar concentration of NaOH solution (mol/L) = 0.0940

A commercial vinegar is analyzed for the percent acetic acid present. The data for the first trial is given below. Calculate the required quantities using the raw data below. Preparation of Vinegar Sample: • Mass of vinegar (g) = 3.06 Analysis of Vinegar Sample: • Buret reading, initial (mL) = 25.40 • Buret reading, final (mL) = 3.70 • Molar concentration of NaOH solution (mol/L) = 0.0940

Chemistry for Today: General, Organic, and Biochemistry

9th Edition

ISBN:9781305960060

Author:Spencer L. Seager, Michael R. Slabaugh, Maren S. Hansen

Publisher:Spencer L. Seager, Michael R. Slabaugh, Maren S. Hansen

Chapter7: Sollutions And Colloids

Section: Chapter Questions

Problem 7.2E

See similar textbooks

Similar questions

Magnesium sulfate (MgSO4) has a solubility of 38.9 g/ 100 g H2O at 30C. A solution is prepared by adding 9.50 g of MgSO4 to 25.0 g of water at 40C. A homogeneous mixture is obtained. Is the solution saturated, unsaturated, or supersaturated? One gram of magnesium sulfate is added to the solution cooled to 30C. Would you expect some of the MgSO4 to precipitate? If so, how much? If not, how much more MgSO4 can be added before precipitation takes place?
In the standardization of HCl using pure anhydrous sodium carbonate as the primarystandard for methyl orange as an indicator, 1.0 mL HCl was found to be equivalent to 0.05gof sodium carbonate (MW =106). The normality of HCl is:
1.44 grams of a sample of marble (impure calcium carbonate) dissolved in 40 ml of 1.0 normality (N) of hydrochloric acid, then add an amount of distilled water to the resulting solution, and its volume became 100 ml, it was found that 25 ml of this resulting solution (mixture) needs 19 ml of 0.2 normality (N) NaOH solution. Calculate the normality (mole/L) of the mixture solution and then calculate the percentage of pure calcium carbonate in this sample. If you know that the molecular weight of pure calcium carbonate is 106 g/mol. *
: 1.44 grams of a sample of marble (impure calcium carbonate) dissolved in 40 ml of 1.0 normality (N) of hydrochloric acid, then add an amount of distilled water to the resulting solution, and its volume became 100 ml, it was found that 25 ml of this resulting solution (mixture) needs 19 ml of 0.2 normality (N) NaOH solution. Calculate the normality (mole/L) of the mixture solution and then calculate the percentage of pure calcium carbonate in this sample. If you know that the molecular weight of pure calcium carbonate
One way in which the useful metal copper is produced is by dissolving the mineral azurite, which contains copper(I) carbonate, in concentrated sulfuric acid The sulfuric acid reacts with the copper(I) carbonate to produce a blue solution of copper(I) sulfate. Scrap iron is then added to this solution, and pure copper metal precipitates out because of the following chemical reaction: Fe(s) + CuSO4(aq) -> Cu(s) + FeSO4(aq) Suppose an industrial quality-control cherist analyzes a sample from a copper processing plant in the following way. He adds powdered iron to a 300. mL copper(I) sulfate sample from the plant until no more copper will precipitate. He then washes, dries, and weighs the precipitate, and finds that it has a mass of 75. mg Calculate the oriqinal concentration of copper(I) sulfate in the sample. Round your answer to 2 significant digits.