a) In your own words, explain in detail the concept of torsion; ensure that the most important properties of torsion are adequately described and provide relevant formula(s) (including typical units) and sketches to support your answer. b) For the bar shown below, identify the location and value of the absolute maximum shear stress. The radius of AC is 81 mm and of CD is 135 mm. Take J = ½nd. Create an internal torque diagram to assist you in answering this question. A B C D 216 N-m 144 N-m 270 N-m 90 N-m X 3.6 m 3.6 m 2.7 m

a) In your own words, explain in detail the concept of torsion; ensure that the most important properties of torsion are adequately described and provide relevant formula(s) (including typical units) and sketches to support your answer. b) For the bar shown below, identify the location and value of the absolute maximum shear stress. The radius of AC is 81 mm and of CD is 135 mm. Take J = ½nd. Create an internal torque diagram to assist you in answering this question. A B C D 216 N-m 144 N-m 270 N-m 90 N-m X 3.6 m 3.6 m 2.7 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the indicated part. What would be the maximum torque that can be applied to the indicated part if the bar is solid, made of steel, with a diameter of 5 cm, L = 2m and the total angle of torsion in the length cannot exceed 2 degrees? Assume G = 80 GPa. (Hint: Twist angle has to be in radians to use in formula)
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
topic: torsion in circular shafts Determine the torsion on the rigid supports and the maximum shearing stress developed in each segment. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right
a) The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion) i) The second moment of area relative to z-axis, I_z, for the cross-section can be calculated as ( Enter your answer in cm4 ii) The bending stress at Point H can be calculated as (Enter your answer in MPa, Compressive stress is negative and tensile stress is positive) iii) The first moment of area required to calculate shear stress at H can be calculated as (Enter your answer in mm^3) iv) The absolute value of the transverse shear stress at point H can be calculated as (Enter your answer in MPa ) v) Maximum principal stress can be calculated as (Enter your answer in MPa ) vi) Minimum principal stress can be calculated as (Enter your answer in MPa ) vii) The equivalent stress for Maximum-Shear-Stress Theory ( Tresca criterion) (Enter your answer in MPa ) b) The von Mises equivalent stresses at point H can be calculated as: MPa c) The factors of safety at point H…
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
A pulley is keyed to a 56.8mm diameter shaft by a 7/16 in x 3 in flat key. The shaft rotates at 697 rpm. The allowable compressive stress for the key, hub and shaft are 66 ksi. 59 ksi and 72 ksi, respectively. Determine the maximum torque, in lb-in, the pulley can safety deliver. Express your answer in 3 decimal places.
QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular CE. The shaft is made of titanium alloy steel and fixed at A. Segment AB is a hollow shaft, has an inner diameter of 25mm. While tube CE with the thickness 2mm has an outer diameter of 20mm. The assembly is subjected to torques of 1000 Nm at C, 210 m at D and 350 Nm at E. The alloy has modulus of rigidity, G = 44kN/mm^2 a) Draw the torque diagram of the shaft. b) Determine maximum shearing stress developed in each segment. c) Calculate the angle of twist at the right end of the shaft.
(7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the crankshaft @ the upper end & bearing @ the lower end 560mm apart. (a) If the engine develops 15kW @ this speed, what is the diameter of the solid steel shaft to use? The allowable torsional stress is 80N/mm2 .
A 2Hp motor rotates at 1500 rpm. If the allowable torsional stress is not to exceed 40 MPa, what is the minimum diameter of shaft?
A shaft with a diameter of 50 mm and a length of 1300 mm with a safe shear yield strength of 20 N / mm2 is subjected to 565 Nm of torque. What is the torsion angle and applicability? (G = 80GPa)
A flanged bolt coupling consists of eight 10 mm diameter steel bolts on a bolt circle 400 mm in diameter, and six 10 mm diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the bolts?