Q3:- A p-type silicon sample with the rectangular geometry has parameters L= 2mm,W= 0.1mm, and d = 8 µm. The semiconductor parameters are p = 1016 cm³ and µp=320 cm?/V-s. For Vx = 10 V and B2= 500 gauss = 5 x 102 tesla, determine Ix and VH .%3D

According to the question we have to find the value of Ix and VH.

Answered: :- A p-type silicon sample with the…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

conducting line on an IC chip is (2.8 mm) long, and has a rectangular cross-section (1x 4 um). A current of (5 mA) produces a voltage drop of (100 mV) across the line. Determine the electron concentration given that the electron mobility is (500 cm²/V.Sec.).
Density of state of copper The Density of state for copper 8.9 gm/cm^3 Q1)Find and explain: a-The fermi level is located at........b-The energy gap = Q2)Choose and explain: a-The boud gap is (small-big)b-This means that copper is a(conductor-semiconductor-)
Draw band diagrams for below contacts. a) metal-n-type semiconductor for Φm< Φs b) metal-n-type semiconductor for Φm> Φs c) metal-p-type semiconductor for Φm< Φs d) metal-p-type semiconductor for Φm> Φs Clearly specify type of contact, Schottky barrier, built-in-potential and the depletion width in the band diagram
The linear electron and hole concentration profiles in a 4 um wide region of silicon material is shown in the figure below. The silicon material is subjected to electron injection from the left and hole injection from the right as shown in the figure. Assume that the cross-sectional area of the material ?=1 ??2, electron mobility ??=1312.75 ??2/? ?, and hole mobility ??=463.33 ??2/? ?. Find the total current (to one decimal place) flowing through the material. ?=300?, ?=1.6×10−19 ?, ?=8.62×10−5 ??/?, ?=1.38×10−23 ?/?, and 1 ??=1.6×10−19 ?. Explain how depletion and diffusion capacitances differ
At what temperature will intrinsic silicon become an insulator, based on the deﬁnitions in Table ? Assume that μn = 1800 cm2/V·s and μp = 700 cm2/V·s.
A sample of n-type silicon semiconductor has the following properties:Donor density Ndis 5x1019per cm3Mobility of electron is 1500 Mobility of hole is 500Electron charge q = 1.602x10-19coulombs.Intrinsic carrier density ni= 1.45x1010per cm3a)Find the density of holes and electrons in this sampleb)Find the conductivity of the given sample if the. c)What is the resistivity of the given sample?
A string of 8 suspension insulators is to be fitted with a grading ring. If the pin to earth capacitances are all equal to C, find the values of line to pin capacitances that would give a uniform voltage distribution over the string.
Die per Wafer: Given a wafer of diameter 300mm and a chip size of 2cm x 2cm, estimate the number of good dies per wafer considering a yield of 85%.
A silicon semiconductor is in the shape of a rectangular bar with a crosssectional area of 10 μm × 10 μm, a length of 0.1 cm, and is doped with Arsenic at 5 × 1016 atoms/cm3 concentration. (T = 300 K).a) determine the current if 5 V is applied across the length. b) repeat part (a) if the length is reduced to 0.01 cm. c) calculate the average drift velocity of electrons in parts (a) and (b). (µn=1350 cm2/volt-s)
A silicon semiconductor has a shape of a rectangular bar with a cross sectional area of 1x10-6cm2 and a lenght of 0.1 cm. How do i calculate the current through the semiconductor if a basis of 5 volts is applied across its length?
It is required to grade a string having seven suspension insulators. If the pin to earth capacitance are all equal to C, determine the line to pin capacitance that would give the same voltage across each insulator (C1, C2, …….C6) of the string.
In the neighborhood of a certain semiconductor junction, the volume charge density is given by Py = 750Sech10^6 pi * tanh10^6 pix C/m³. The dielectric constant of the semiconductor material is 10 and the junction area is 2 x 10^-7m². Find; (a) Vo; (b) C; (c) E at the junction.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

:- A p-type silicon sample with the rectangular geometry has parameters I 0.1mm, and d = 8 µm. The semiconductor parameters are p = 1016 cm³ cm?/V-s. For Vx = 10 V and B,= 500 gauss = 5 x 102 tesla, determine Ix a