Consider a hollow steel shaft with a 130 mm outside diameter and a 70 mm inside diameter. What is the maximum torque this shaft can transmit if the shear yield stress is 1.4x108 Pa and the behavior is elastic, perfectly plastic?

Consider a hollow steel shaft with a 130 mm outside diameter and a 70 mm inside diameter. What is the maximum torque this shaft can transmit if the shear yield stress is 1.4x108 Pa and the behavior is elastic, perfectly plastic?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Related questions

Q: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft which…

A: INTRODUCTION : When the circular shaft either hollow or solid is used to the power transmission, the…

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: A) Angle of twist for the given max shear stress in a hollow shaft: The angle of twist of a hollow…

Q: Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the…

A: Given Data⇒ Hollow steel shaft Outside diameter of shaft(D)=130 mm=0.13 m Inside diameter of…

Q: A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the…

A: Given: Power transmitted by the shaft P=75kWSpeed of the shaft N=200rpmModulus of rigidity…

Q: A solid circular shaft is subjected to combined bending and torsion and and made of steel having…

Q: Example 19.19. A torsion dynamometer is fitted to a propeller shaft of a marine engine. It is found…

Q: A hollow shaft with outside diameter of 135 mm and wall thickness of 8 mm transmits 182 kW at 400…

A: L=5m 1psi= 6894.76 N/m2

Q: A cube of a material with a yield strength of 100x10° N/m*is subjectedtotheloads shown onthe right.…

Q: A propeller shaft is required to transmit 45 kW power at 500 r.p.m. It is a hollow shaft, having…

A: Given data: - The power transmitted by the shaft is P = 45 kW. The speed of the shaft is N = 500…

Q: Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the…

A: Given, diameter of the wrench , d=2×0.4 cm=0.8 cm=8 mm Length, L=200 mm Allowable shear stress,…

Q: A horizontal shaft of 75 mm diameter projects from a bearing, and in addition to the torque…

A: Shear stress is stress which produces due to pressure or forces which does not exceed the elastic…

Q: A mild steel shaft of 40 mm diameter is subjected to a bending moment of 115 N-m and torque, T. If…

Q: A plat spiral spring is made of 6 mm wide.and 2.5 mm thick wire andis 250 cm long. Assuming the…

A: Given data: width of spring = 6 mm Thickness of wire = 2.5 mm length = 250 cm Maximum stress = 840…

Q: A shaft with a length of 2 m has the cross section shown in Figure 1, where a = 4 cm and t = 4 mm.…

A: Torque Torque is a rotational equivalent of linear force. Torsion Torsion is the twisting of an…

Q: A stepped steel shaft shown below is subjecte to 10 N-m torque. If the moduius of rigidity 80 GPa,…

A: Given:Torque, T=10 N-mG=80 GPad1=50 mmd2=25 mmL=100 mm

Q: A hollow aluminum tube used in a roof structure has an outside diameter of 104 mm and an inside…

A: Given data: τ=48 MPaD=104 mmd=82 mmL=2.75 mG=28 GPa Need to determine the angle of twist.

Q: A shaft capable of transmitting 50 kW of power will spin at 100 revolutions per minute. The maximum…

A: Given Power, P = 50 kW Speed, N =10 0 rpm Length, l = 3 m Angle = 1.5 degree Find Diameter,…

Q: A hollow circular shaft has an external diameter of 0.120 m and the internal diameter а) is…

Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 10 N/mm² and length of…

A: Given data as per question shaft dimeter =125 mmPower transmitted =120 kwSpeed=160 rpmC = 8×10…

Q: Example 1 A shaft is transmitting 100 kW at 160 rp.m. Find a suitable diameter for the shaft, if the…

A: Stress: When a component or a part is subjected to any external force, a resisting force will be…

Q: A 1 m length of 50 mm diameter steel bar is subjected to a torque of 230 Nm. Calculate the maximum…

Q: Compute the torsional deflection in degrees of a 110 mm diameter, 1.4 meter long shaft subjected to…

A: GIVEN DATA- D=110mm T=3*10^6Nmm G=83000 N/mm2 WE HAVE TO CALCULATE TORSIONAL DEFLECTION IN DEGREE

Q: mild steel shaft of 50 mm diameter is subjected to a bending moment of 2000 N-m and a torque T. If…

Q: A shaft has an external diameter (ED) of 350 mm and an internal diameter of 150 mm.…

A: Given that, External diameter of shaft, D=350 mm,Internal diamter of shaft, d=150 mm,Length of…

Q: A hollow shaft with outside diameter of 165 mm and wall thickness of 8 mm transmits 192 kW at 400…

Q: A shaft is required to transmit 1 MW power at 240 r.p.m. The shaft must not twist more than 1 degree…

A: Find the diameter of shaft and shear stress in the shaft.

Q: A solid shaft 125 mm in diameter transmits 120 KW at 160 rpm. Taking C = 8 x 104 N/mm2 and length…

A: Write the expression to determine the powerP transmitted by a shaft. P=2πNT60 Here, speed of the…

Q: (a) What is spring ? Briefly define the type of spring. Also explain the formula of stress for flat…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: A hollow 3 m long steel shaft that will provide the main engine drive transmission for a ship to be…

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106…

Q: A 2-inch line shaft is transmitting 20 hp rotating at 200 rpm, carrying two pulleys spaced 30 inches…

Q: A 10 m length shaft is used to transmit 50 kw power at 450 rpm. If the shaft stress is limited to 40…

A: Given Length, L = 10 m Power, P = 50 kW Speed, N = 450 rpm Stress = 40 MPa Find…

Q: 2.29. A cylindrical steel shaft is required to transmit a bending moment of 1000 Nm and a torque of…

Q: A solid circular shaft to transmit,80kw power at 200rpm.calculate the shaft diameter and strain…

Q: The shaft of a 7 HP lawnmower is 25mm in diameter and rotates at 1200 rpm. Calculate the shear…

Q: The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and…

A: Given: The yield strength of material, Sy = 600 MPa The ultimate strength of the material, Su = 700…

Q: Example 7.5: (Numerical problem of a circular shaft) A circular shaft 10 cm diameter and 1.1 m…

Q: A steel shaft 1.4375 inches in diameter transmits 40 hp at 1400 rpm. Assuming a modulus of rigidity…

Q: A torque T applied to a 1.2 m long and 50 mm diameter solid shaft increases until the shaft is fully…

Q: A shaft ABCD 70 mm in diameter is subjected to torques of 1500 N-m at B and 1100 N-m at C acting in…

Q: A thin tube of uniform thickness 5 mm and square cross section, shown below, is subject to a torque…

Q: Find the diameter of a shaft to tansmit twisting moments varying from 800 N-m to 1600 N-m. The…

A: GIVEN DATA MAXIMUM TORQUE T=1600N-m MINIMUM TORQUE T=800 N-m σut=600MPa σy=450 MPa Kt=1.2…

Q: Consider a bar of cast iron under complex loading. The bar is subjected to a bending moment of M =…

Q: The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and…

Q: Q6: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft…

A: The engine of a ship develops 440 kW and transmits the power by a horizontal propeller shaft which…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Consider a hollow steel shaft with a 130 mm outside diameter and a 70 mm inside diameter.
What is the maximum torque this shaft can transmit if the shear yield stress is 1.4x108 Pa and
the behavior is elastic, perfectly plastic?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing maching until the applied torque reaches the value T = 500 N ·. At this value of torque, a strain gage oriented at 45º to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A thin-walled hollow tube AB of conical shape has constant thickness I and average diameters dAand dBat the ends (see figure). Determine the strain energy U oT the tube when it is subjected to pure torsion by torques T, Determine the angle of twist of the tube. Note: Use the approximate formula / ird^tlA for a thin circular ring; see Case 22 of Appendix E.
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.