An open circular ring of circular cross section (with diameter d) is subject to two equal and opposite out-of-plane tip forces Q as shown. Find the relative displacement of the two ends of the ring. Note that you must consider both the work of bending and torsion. Estimate the relative contributions of bending and torsion to the relative displacement.

An open circular ring of circular cross section (with diameter d) is subject to two equal and opposite out-of-plane tip forces Q as shown. Find the relative displacement of the two ends of the ring. Note that you must consider both the work of bending and torsion. Estimate the relative contributions of bending and torsion to the relative displacement.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.18P: A stepped shaft ABC consisting of two solid, circular segments is subjected to uniformly distributed...

See similar textbooks

Similar questions

A heavy flywheel rotating at n revolutions per minute is rigidly attached to the end of a shaft of diameter d (see figure). If the bearing at A suddenly freezes, what will be the maximum angle of twist <£of the shaft? What is the corresponding maximum shear stress in the shaft? (Let L = length of the shaft, G = shear modulus of elasticity, and / = mass moment of inertia of the flywheel about the axis of the shaft. Also, disregard friction in the bearings at Sand Cand disregard the mass of the shaft.) Hint: Equate the kinetic energy of the rotating flywheel to the strain energy of the shaft.
A vertical shaft 20 mm in dia and 100 cm long is mounted in long bearings and carries a rotor of mass 10 kg midway between bearings. The center of rotor is 0.5 mm away from axis of shaft. Neglect the weight ofshaft and take E-200 GPa forshaft material. Determing whirling speed of shaft and bending stress induced in it when it is rotating at 2000 rpm.
The length of the smooth circular shaft with a solid cross-sectional area of 315nm2 is 1 meter. Instead of this shaft, it is desired to use an evacuated circular-section shaft with a wall thickness of 3 mm with the same length and weight. For these two cases, compare the angles of rotation that would occur if a moment M = 600 (N.m) was applied to the end of the shaft made of material G-80 GPa.
A shaft having length equal to 10 m and diameter equal to (50+ 01) mm is simply supported at both ends. The shatt carries four masses (150 + 01) kg, (200 + 01) kg, (250 +01) kg and (300 + 01) kg. These masses are located at a distance of 1.5m, 2.5 m, 5.5 mand 7.5 m from the left hand side support, respectively. The modulus of elasticity, E, for the material of the shaft is 200 GN/m? and mass density for the shaft material is 7500 kg/m?3. Determine critical speed of the shaft in revolutions per minute for the following two cases: 1. Effect of the mass of the shaft is neglected. 2. Effect of the mass of the shaft is considered. What is the usefulness of the answers determined in this problem?
A brass flat, clamped disk valve of 0.4 m diameter and 0.020 m thickness is subjected to a uniform liquid pressureof 400 kPa.1. Define the boundary conditions at the edges of the plate2. Calculate maximum deflection of the disk3. Calculate maximum and transverse bending moments4. Determine maximum bending stresses and its location If the disk is assumed simply supported,5. Define the boundary conditions at the edges of the plate6. Calculate maximum deflection of the disk7. Calculate maximum and transverse bending moments8. Determine maximum bending stresses and its location
A uniform beam, of mass 31 kg/m run, is simply supported on a span of3.6 m. Taking EI for the beam as 7 MN.m2, calculate the frequency oftransverse vibrations.This frequency is to be reduced by 40% by fixing three equal masses tothe beam, at the mid-point and the quarter points. Calculate how muchthese masses should be.
A stepped shaft ABC consisting of two solid,circular segments is subjected to uniformly distributedtorque t1 acting over segment 1 and concentratedtorque T2 applied at C, as shown in the figure. Segment1 of the shaft has a diameter of d1 = 57 mmand length of L1 = 0.75 m; segment 2 has a diameterd2 = 44 mm and length L2 = 0.5 m. Torque intensityt1 = 3100 N . m/m and T2 = 1100 N . m.(a) Find reaction torque TA at support A.(b) Find the internal torque T(x) at two locations:x = L1 /2 and at x =L1 + L2 /2. Show theseinternal torques on properly drawn free-bodydiagrams.
A three-dimensional elastic body with dimensions b=2m, h=60cm and a=80cm was subjected to forces of Fx = 960kN and Fy = 4800kN. Since E=210GPa, V=0.3, find the length changes and volume changes in the x, y, z axes.
Under non-uniform and slippery road conditions, two forces (u and w), shown in the figure (image 1), are performed on the truck's rear wheels, which have a limited slip rear differential. Choose the alternatives that are true: (data: u = 92lbf and w =57lbf) (obs1.0: 1''= 1 in = 25,4mm) (obs2.0: 1lbf = 4,448N) a) the force vector resulting from the two forces is -149i [lbf] b) the resultant of the two forces has an intensity equal to 149lbf c) the ordinate of the point of intersection of the line of action of the resultant of this system of forces with the y axis is 7.05in d) adopting the counterclockwise direction as positive, the total moment of the two forces in relation to point g is equal to -1050lbf.in e) the total moment vector in relation to the G point is equal to -1050i [lbf.in]
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.d) where is the centroid?e) what is the area?f) Calculate the shear modulus
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.g) Compute each of these moments of inertia with the values b = 0.4 m, d =0.5 m , t =0.1 m.
3) The force, FT = 1 kN, and moment, MT = 0.5 kN-m, at the tip are caused by a wing tip vortexand a winglet, not shown. L = 12 m and the spar has an elastic modulus of E = 70 GPa and aPoisson’s ratio of n = 0.33. The mass of the wing is 4000 kg, and the weight of the engine is 107kN. Use 9.8 m/s 2 for the acceleration due to gravity.Consider the cross-section shown (you can look these up). Pay attention to the coordinate systemgiven in the drawing.a) what is the moment of inertia about y-axis in terms of the symbolic dimensions shown?b) what is the moment of inertia about z-axis in terms of the symbolic dimensions shown?c) what is the polar moment of inertia in terms of the symbolic dimensions shown (i.e.about the x-axis)?d) where is the centroid?e) what is the area?f) Calculate the shear modulusg) Compute each of these moments of inertia with the values b = 0.4 m, d =0.5 m , t =0.1 m.