An oven used for curing plastic parts has a front glass of L = 0.05 m thick. the outer surface of the glass is exposed to a wide range of environment and air. the temperature of air and environment is 300 Kelvin. If the temperature of the outside of the glass is 400 K and radiating rate E=0,8 and thermal convection coefficient of air h=20 W/m2K, what is the front side of glass temperature?

An oven used for curing plastic parts has a front glass of L = 0.05 m thick. the outer surface of the glass is exposed to a wide range of environment and air. the temperature of air and environment is 300 Kelvin. If the temperature of the outside of the glass is 400 K and radiating rate E=0,8 and thermal convection coefficient of air h=20 W/m2K, what is the front side of glass temperature?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.1P: 1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed...

See similar textbooks

Similar questions

A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
1.1 On a cold winter day, the outer surface of a 0.2-m-thick concrete wall of a warehouse is exposed to temperature of –5°C, while the inner surface is kept at 20°C. The thermal conductivity of the concrete is 1.2 W/m K. Determine the heat loss through the wall, which is 10-m long and 3-m high. Problem 1.1
3.10 A spherical shell satellite (3-m-OD, 1.25-cm-thick stainless steel walls) re-enters the atmosphere from outer space. If its original temperature is 38°C, the effective average temperature of the atmosphere is 1093°C, and the effective heat transfer coefficient is , estimate the temperature of the shell after reentry, assuming the time of reentry is 10 min and the interior of the shell is evacuated.
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
A 1 in. o.d. (outer diameter) tube reactor is insulated with a 3 inch layer of asbestos. If the temperature of the outer surface of the insulation is 100 °F and the rate of heat loss per foot of reactor length is 50 BTU/hr, what must the temperature of the inside of the reactor be? [for asbestos, k = 0.105 BTU/hr ft °F]
The heat conducts through the shape below. The temperature of the right face is 93 °C, while the left face is at 23 °C. If the top and bottom faces are completely insulated, and the thermal conductivity of the material decreases with decreasing temperature. * Assume that the thermal conductivity is 100 at 23, decreased to 10 at 93. A) Sketch the temperature profile inside the plate. B) If both sides of the plate in the above problem is exposed to air: Left side (h = 20 W/m2K, TL = 20 °C) and right side (h = 90 W/m2K). Calculate the temperature of the air on the right side.
Question 1: A glass window of width W = 1 m and height H = 2m is 5 mm thick and has a thermal conductivity of kg =1.4 W/m.K. If the inner and outer surface temperatures of the glass are 15 °C and -20 C, respectively, on a cold winter day, what is the rate of heat loss through the glass? To reduce heat loss through windows, it is customary to use a double pane construction in which adjoining panes are separated by an air space. If the spacing is 10 mm and the glass surfaces in contact with the air have temperatures of (last two digit of your Registration number) °C and -15 °C, what is the rate of heat loss from a 1 mx2mwindow? The thermal conductivity of air is ka = 0.024 W/m.K.
An electric wire having a diameter of 1.5 mm and covered with a plastic insulation (thickness = 2.5 mm) is exposed to air at 300 K and ho = 20 W/m2.K. The insulation has a thermal conductivity (k) of 0.4 W/m.K.Assuming the wire surface temperature is constant at 400 K and is not affected by the coveringa) Calculate the value of the critical radius.b) Calculate the heat loss per meter of wire length with no insulation.c) Calculate the heat loss per meter of wire length with insulation. p.s Could you write the solution clearly? It is hard to understand when written in text. A paper photo with solution would be better. Thanks in advance
A furnace wall is to consist in series of 7 in of kaolin firebrick, 6 in of kaolin insulating brick, and sufficientfireclay brick to reduce the heat loss to 100 Btu/ hr ft2 when the face temperatures are 1500 and 100°F,respectively.a) Show the figure of the systemb) What thickness of fireclay brick should be used?c) If an effective air gap of 1/8 in can be incorporated between the fireclay and insulating brick whenerecting the wall without impairing its structural support, what thickness of insulating brick will berequired?
What is the rate of heat transfer, temperature gradient, and the direction of the heat transfer through a piece of Celotex 3 ft by 8 ft by 1 in. in thickness, if the temp of one surface is 80°F and of the other side is 60°F? - thermal conductivity of Celotex in AES = 0.028.
Consider a two-layer sphere with inside fluid convection rate h1 and outer rate h2. The first layer has inside radius r1 and outside radius r2. The second layer has outside radius r3. What is the general equation for the total resistance? Neglect thermal contact resistance.
A thick wallet tube of stainless steel (k+10 W/M°C) with 2 cm inside diameter and 4 cm outer diameter is covered with a 3 cm layers of asbestos insulation (K= 0.2 W/M°C), if the inside wall temperature of the pipe is maintained at 600 degree C , Calculate the heat loss per meter of length, Also calculate the tube - insulation interface temperature. Draw the Coresponding diagram. Ambient temperature is 2°C.