diluting a 0.40M CuSO4 stock solution with water, calculate the concentration of each of the solutions ( trials ). Trial Volume(mL) 0.40M CuSO4 volume(mL) Dl H20 new concentration CuSO4 1 2.0 8.0 2 4.0 6.0 3 6.0 4.0 4 8.0 2.0 5 10.0 0.0

diluting a 0.40M CuSO4 stock solution with water, calculate the concentration of each of the solutions ( trials ). Trial Volume(mL) 0.40M CuSO4 volume(mL) Dl H20 new concentration CuSO4 1 2.0 8.0 2 4.0 6.0 3 6.0 4.0 4 8.0 2.0 5 10.0 0.0

Chemistry: The Molecular Science

5th Edition

ISBN:9781285199047

Author:John W. Moore, Conrad L. Stanitski

Publisher:John W. Moore, Conrad L. Stanitski

Chapter3: Chemical Reactions

Section: Chapter Questions

Problem 87QRT: You need 300. mL of 0.500-M K2Cr2O7. Which method is best to prepare this solution? Explain your...

See similar textbooks

Related questions

Q: Ten pints of a 5% solution are diluted with 30 pints of diluent, what is the percentage strength of…

A: Initial amount = 10 pints Diluted by 30 pints. So, final amount = 10+30 = 40 pints. So, dilution…

Q: t was suspected that a certain fish contains Hg due to bioaccumulation. 5.00 g of fish meat after…

A: Volume of solution = 0.100 L concentration of Hg in solution = 45.0 ppm Mass of fish meat = 5.00 g…

Q: 100.0 mL of a 0.500 M solution of KBr is diluted to 500.0 mL. What is the new concentration of the…

A: The given problem relates to stock dilution, so we can use the below relation to calculate the final…

Q: What is the molarity of an aqueous solution that contains 0.0720 g CaH.O2 per gram of solution . The…

Q: Preparation of HCI solution a. Measure 20.7 ml of concentrated Hcl (37% wt HCI) using the pipet and…

Q: 3. Place 0.5 mL of 0.5 M HNO, into each of the five test tubes. 4. Add: Test tube A: 1 drop…

A: A question based on equilibrium concept and quantitative analysis, which is to be accomplished.

Q: please answer questions 1) and 2) (they are part of the same question). thank you

A: The term number of moles is defined as the ratio of mass to the molar mass of the given compound.…

Q: What willl be the Molar concertration of the 333.85 HCl solution prepared from 4 mL of concentrated…

A: Volume of HCl solution = 333.85 ml Can consider unit in ml to solve this problem. Volume of…

Q: Preparing and Diluting Solutions Data Table Test Tube 1* 2 4 10ML/3.8mL 2.4mL SmL 1.53ML…

A: We are given the data for the concentration of different diluted stock solutions and their…

Q: Calculate the amount of ferrous ammonium sulfate [Fe(NH4)2(SO4)2•6H2O](MM = 392.14 g/mol) needed to…

A: In order to calculate the required strength of the solution, first of all calculate the amount of…

Q: Determine the number of moles of AgNO3 in 25.0 ml of 0.600 M AgNO3. Show solution.

A: Given, The number of moles of AgNO3 present in 25.0 mL of 0.600 M AgNO3 solution is:

Q: Calculate the solubility of Mg(OH)2 in 0.10 M Mg(NO3)2. Calculate the solubility in grams/liter…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Volume of Volume of 0.1 M HCI solution Volume of Concentration 0.2 M Na,s,0, Time (s) distilled of…

A: Titration is the quantitative method of estimating the strength of the any component. Molarity is…

Q: Please calculate the grams of each substance needed to make the following solutions: One-half…

A: Given: The volume of the solution of CaSO3, (V) = 05 L. The molar mass of CaSO3, (M) = 120.17 g/mol.…

Q: what are the materials for the preparation of 0.25 M Hydrochloric acid (HCl) solution using 3.86 mL…

A: We can solve this problem by recall the formula of molarity Molarity = mole of solute/volume of…

Q: A municipal water sample has 0.20 ppm Pb2+ by weight. The density of this sample is 1.00 g/mL. How…

A: Hey, since there are multiple questions posted, we will answer first question. If you want any…

Q: The solubility of manganese(II) hydroxide (Mn(OH)2) is 2.2 × 10-5 M. What is the Ksp of MnOH)2?…

A: Step 1Given, solubility of Mn(OH)2 at 20∘C= 2.2×10-5M find out: Ksp of Mn(OH)2 at 20∘C =?

Q: # Solutions Overall dilution Concentration factor (relative to the original sample) (0.00998M )…

A: By help of Molarity formula, we can calculate the new concentration or Molarity of the new Solution.…

Q: SOLUTION CONCENTRATION FUNDAMENTAL QUIZ (V4) This quiz will be scored on a pass/fail basis. Show all…

Q: 53.2 mL of 0.795 M hydroiodic acid is added to 46.2 mL of barium hydroxide, and the resulting…

Q: A sample of 6 M 10 mL H2SO4 is diluted to 100 ml. Calculate the concentration ( in gravimetric…

A: On the dilution of an acid, the concentration (molarity) of the solution decreases. The number of…

Q: 12.0−mL portion of 7.00 M stock solution is to be diluted to 0.300 M. What will be the final volume…

A: Molarity is defined as total number of solute present in 1000 ml of solution . For neutralisation…

Q: Concentration (mg/dL) Stock Standard (mL) Distilled H2O Total Volume of Dilution (mL) 0 0.0…

A: Formula used Vol.of stock(V1) * Concentration of stock(M1) = Total Volume(V2) * Final…

Q: trial molarity of Hci molarity of NaOH volume of HCI volume of NaOH 1 1M 2M 200mL 200mL 2 1M 1M…

A: Limiting reagent is the species which present in lesser amount and get completely consumed during a…

Q: If you have 155 mL solution of a 0.762 M FeCb solution, how many g FeCb are contained in this…

Q: Concentration (M) of starting solution 0.024 Abs (7.5 mL 0.024 M Cu2* +7 mL conc NH3 diluted with…

A: Initial volume of Cu2+ solution,V1 = 7.5 ml Initial concentration of Cu2+, M1 = 0.024 M Final volume…

Q: 3..How many grams of CrF3 will dissolve in 250 mL of water? For CrF3 the molar mass is 108.99 g/mol…

A: Given-> Volume = 250 ml = 0.250 L. (1L = 1000 ml) Molar mass of CrF3 = 108.99 g/mole Ksp =…

Q: Please answer as soon as possible. Thank you! A 10.000-g cocoa powder sample was dissolved in…

A: First of all, we have to convert the concentration of Fe given in micromolar to the grams of Fe in…

Q: The labware we used in Quant Lab is divided into “qualitative” or “quantitative” analytical purpose.…

A: 2ml of H2SO4 solution would be pipetted out into a flask to dissolve the copper oxide ore sample.…

Q: What willl be the Molar concertration of the 306.29 HCl solution prepared from 3 mL of concentrated…

A: To solve this problem we will first calculate mass of HCl . Then number of mole HCl will be…

Q: Dissolution 0.01 M HCI Distilled H20 Concentration (mg/ml) Total amount Concentration (mg/ml) Time A…

A: Dissolution is the process where a solute in gaseous, liquid, or solid phase dissolves in a solvent…

Q: Q22: Phosphate buffer solution is purchased as a(n) 2x stock solution. The solution is more…

Q: 2. What is your smallest volume that you can comfortably measure with your P20 pipettor? Can you…

A: Solution is a homogeneous mixture of solute and solvent. Concentration of a solution is the amount…

Q: 3)The molarity of 48.0 mL of 6.00 M H2SO4 diluted to 0.250 L is: Select one: A. 2.25 M B. 3.35 M…

A: Answer: The molarity of 48.0 mL of 6.00 M H2SO4 diluted to 0.250 L is 1.15 M. so option D. 1.15 M is…

Q: Which of the following will result to a dimly lit light bulb when subjected to the conductivity…

A: The correct option is:

Q: Calculate the [CI] for a solution prepared by dissolving 1.525 g BaCl2.2H2O (244 g/mol) and 1.17 g…

A: Molarity(M) is the moles of solute per unit volume of the solution in litres. It's unit is mol/L…

Q: If a 10.0mL volumetric flask is used to prepare the dilution, what volume of 0.50 M cobalt (II)…

Q: What is the final molarity of sodium thiosulfate pentahydrate for each of the runs? Given: the…

Q: While making a stock solution of NaSCN using 0.8 g of NaSCN in a 10 mL volumetric flask. 750…

A: According to the mole concept, in terms of mass, the amount of substance in moles is equal to the…

Q: 100 mL of 2.00 µg/mL of Cu from 1000 PPM Cu Standard Solution.

A: The explanation is given below-

Q: Isotonic saline solution is 0.154 M NaCl(aq). What is the solubility of AgCl (Ksp = 1.8 × 10−10) in…

A: Given data : Concentration of NaCl = 0.154 M Ksp of AgCl = 1.8 × 10-10

Q: The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on…

A: Molarity of a solution can be obtained by dividing the number of moles of solute by the volume of…

Q: It is known that acid content has a major effect on the flavor of vinegars, but most cheaper…

A: Decreasing the concentration of a given solution by addition of solvent or water is called dilution.…

Q: Calculate the percent difference in the two values for the molarity of the NaOH solution by:…

A: Molarity (M) = molesVolume of solution in LNormality (N) = no. of equivalentVolume of solution in L…

Q: 19. If you used more than half of your NAOH solution in buret-refill It to the 0 mL mark on the fon…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: You were tasked to determine the percentages of citric acid in the freshly squeezed and bottled…

A: Citric acid+ sodium hydroxide --->sodium citrate+ water Molarity of NaOH = 1.10M Moles of NaOH=…

Q: Lab. work Nacl is a chemical compound of a molecular mass =58.4 1- prepare 10 ml of one molar…

Q: The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on…

A: Since, Number of moles of a substance is the ratio of mass of the substance to its molecular mass.…

Q: Cesium chloride is used to prepare dense solutions required for isolating cellular components with…

A: Given: Percent by mass of CsCl = 40.0 % And density of solution = 1.43 g/mL. Assuming 1 L i.e. 1000…

Q: Calculate the volume of each solution, volume of water and the total volume. 0.00150 M Fe³+. 0.00150…

A: Here , sample A , B and C are made by mixing two solutions and water and the final volume is 15.00…

Concept explainers

Analytical Tools

Analytical tools or analysis tools help one to get into a conclusion or results from the data collected. Analytical tools can be applied for simple data sets and also in the case of big data analytics.

Question

diluting a 0.40M CuSO4 stock solution with water, calculate the concentration of each of the solutions ( trials ).

Trial	Volume(mL) 0.40M CuSO4	volume(mL) Dl H20	new concentration CuSO4
1	2.0	8.0
2	4.0	6.0
3	6.0	4.0
4	8.0	2.0
5	10.0	0.0

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Calculate the new concentration of CuSO4 for trial 1

VIEW

Step 2 Calculate the new concentration of CuSO4 for trial 2

VIEW

Step 3 Calculate the new concentration of CuSO4 for trial 3

VIEW

Step 4 Calculate the new concentration of CuSO4 for trial 4

VIEW

Step 5 Calculate the new concentration of CuSO4 for trial 5

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Patients undergoing an upper gastrointestinal tract laboratory test are typically given an X-ray contrast agent that aids with the radiologic imaging of the anatomy. One such contrast agent is sodium diatrizoate, a nonvolatile water-soluble compound. A 0.378-m solution is prepared by dissolving 38.4 g sodium diatrizoate (NaDTZ) in.l.60 102 mL water at 3 1.2C (the density of water at 31.2C is 0.995 g/cm3). What is the molar mass of sodium diatrizoate? What is the vapor pressure of this solution if the vapor pressure of pure water at 31.2C is 34.1 torr?
You need 300. mL of 0.500-M K2Cr2O7. Which method is best to prepare this solution? Explain your choice. (a) Dilute 250. mL of 0.600-M K2Cr2O7 to 300. mL. (b) Add 50.0 mL water to 250. mL of 0.250-M K2Cr2O7. (c) Dilute 125 mL of 1.00-M K2Cr2O7 to 300. mL. (d) Add 30.0 mL of 1.50-M K2Cr2O7 to 270. mL of water.
What is normality of a solution containing 90g of HCI in 2600ml of solution? (Use the given information: MW:H=1g/mol, Cl=35g/mol)A. 0.00048 eq/molB. 0.48 eq/molC. 0.00096 eq/molD. 0.96 eq/mol
Weigh out accurately 9.99 g of copper(II) sulfate pentahydrate (CuSO4·5H2O) by taring using a clean and dry empty 250-ml beaker. 2. Add tap water to the beaker to reach the 50-mL mark on the side of the beaker. 3. Dissolve all the crystals of CuSO4·5H2O in the water using a clean glass rod for stirring. 4. Then using a glass funnel transfer all the blue solution to a 100-mL volumetric flask. Rinse the beaker with about 10 mL of water and transfer the solution to the volumetric flask. Repeat the rinsing of the beaker with another 10 mL of water and transfer the solution to the volumetric flask. This is called quantitative transfer of the solution. 5. Then add enough water to reach the calibration mark of the volumetric flask. (You will need to use a dropper to add the last few drops of water to ensure the meniscus is on the calibration mark). Close the volumetric flask with a stopper and mix the solution well (so that it is homogeneous). 6. You have now prepared a standard solution (or…
Which is not required in recrystallization? a. solution is filtered at high temperature b. moderate volatility solvent c. saturated solution d. solvent must dissolve the impurities
5.00 ml of the 1.0 x 10-4 M CV stock solution is first diluted to 100.ml. Then 1.00 ml pf this solution is diluted again to 50.0 ml. What is the final concentration?
How to prepare the solutions listed below Solution 1) 25 mL 7 M sulfuric acid and the respective dilution of this solution to prepare 50 mL 2 M sulfuric acid in deionised water. Sulfuric acid Mw = 98.079 g mol-1 Sulfuric acid density = 1.84 g mL-1 Sulfuric acid purity = 98% Solution 2) 100 mL 0.02M potassium permanganate potassium permanganate Mw = 158.03 g mol-1 potassium permanganate purity = 99%
The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask and add deionized H2O to a final volume of 250.0 mL. Molar mass of H2C2O4•2H2O = 126.07 g/mol Mass of H2C2O4•2H2O = 1.5232g Volume of H2C2O4•2H2O solution = 250.0mL What is the Molarity H2C2O4 standard solution ?
Measure the mass of 0.400g of Co(NO3)2 + 6H2O and dissolve it in 15mL of distilled or deionized water using a clean beaker Then while using a graduated cylinder, measure out 10.0mL of a prepared 0.10-M Na3PO4 soultion. Determine which compound Na3PO4 or Co(NO3)2 *6H2O will be the limliting reagent. Then detrimine the theiretical yeild
Consider a 1.000-L stock solution of 9.69 M Na3PO4. A 2.000-mL aliquot is taken from this stock solution and diluted to a final volume of 1.000 L. A 5.000-mL aliquot is then taken from this new solution and further diluted to make a new solution with a final volume of 750.0 mL. Calculate Na+ in the final solution.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. From the stock solution (0.020 M), pipet 4.00 mL and dilute to 100.00 mL. From the diluted solution, pipet 0.00, 1.00, 1.50, 2.00, 2.50, 5.00 and 7.50 mL aliquots into 100 mL volumetric flasks. Dilute to mark. Determine the concentration of each standard solution and tabulate.
1. A 50.00 mL stock CaCl2 solution was diluted with water in a 250.0-mL volumetric flask. A 25.00 mL aliquot of this was further diluted to a final volume of 100.0 mL. Finally, 20.00-mL aliquot of the resulting solution was analyzed and found to contain 0.1500 M CaCh2 Solve for the concentration of the stock solution in M. 2. A 50.00 mL stock CaCl2 solution was diluted with water in a 250.0-mL volumetric flask. A 25.00 mL aliquot of this was further diluted to a final volume of 100.0 mL. Finally, 20.00-mL aliquot of the resulting solution was analyzed and found to contain 0.1200 g CaCl2 Solve for %w/v CaCl2 in the stock solution.