Explain the color changes observed throughout the peroxide value of oil experiment. Materials: 1. Old and fresh oil samples 2. Distilled water 3. Acetic acid/chloroform solution 4. Saturated potassium iodide solution 5. Sodium thiosulphate (0.01M) 6. 1% Starch indicator: dissolve 1g of starch in 10 ml of water and then add 90 ml of hot water to i

Explain the color changes observed throughout the peroxide value of oil experiment. Materials: 1. Old and fresh oil samples 2. Distilled water 3. Acetic acid/chloroform solution 4. Saturated potassium iodide solution 5. Sodium thiosulphate (0.01M) 6. 1% Starch indicator: dissolve 1g of starch in 10 ml of water and then add 90 ml of hot water to i

Curren'S Math For Meds: Dosages & Sol

11th Edition

ISBN:9781305143531

Author:CURREN

Publisher:CURREN

Chapter9: Parenteral Medication Labels And Dosage Calculation

Section: Chapter Questions

Problem 1.3P

See similar textbooks

Similar questions

explain what the results of this experiment are and the purpose Table 2 Absorbance vs CoCl2 concentration Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.024 3 0.018 0.055 4 0.027 0.085 5 6 0.036 0.045 0.112 0.138 7 (Unknown) 0.088
A chromatographic separation of four compounds gave the following results. The dead time (tm) is 16.7 sec. (a) What is the capacity factor for analyte 4? (b) What is the resolution factor for analytes 3 and 4?
I do not understand the results of this experiment, explain what the results of this experiment are and the purpose Table 2 Absorbance vs CoCl2 concentration Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.024 3 0.018 0.055 4 0.027 0.085 5 6 0.036 0.045 0.112 0.138 7 (Unknown) 0.088
A calibration curve for the absorbance of an unknown is shown below. What would be the concentration of a sample with absorbance of 0.45. Give the answer with the correct unit.
Answer the ff and state references: For his experiment, Brian needs to prepare 30 plates (use maximum volume), 15 slants (small test tube), and 15 stabs (big test tube) of Luria What is the total volume of the medium needed? What is the amount of each component needed, given the following media composition per liter of distilled water: Component g/L tryptone 10.0 NaCl 5.0 yeast extract 10.0 agar 15.0
In sterilization, which among the supplies, instruments, glassware, etc. under the list of materials can be sterilized using either or both equipment below? List them down under the category: a) For “autoclaving” only, B) For Dry heat oven sterilization ,And C) Can be sterilized with either. Materials: 200-ml Erlenmeyer flask Stove 500-ml Erlenmeyer flask Autoclave 10-mL graduated cylinder Analytical balance 100-ml graduated cylinder pH meter Spatula Stirring rod 100-mL beaker Test tubes Distilled water Petri dish Stirring rod Alcohol lamp Glass dropper
Lead nitrate Stock Solution— Dissolve 159.8 mg of lead nitrate in 100 mL of water to which has been added 1 mL of nitric acid, then dilute with water to 1000 mL. Standard Lead Solution— On the day of use, dilute 10.0 mL of Lead Nitrate Stock Solution with water to 100.0 mL. Standard Preparation— Into a 50-mL color-comparison tube pipet 2 mL of Standard Lead Solution, and dilute with water to 40 mL, and mix. Test Preparation— Into a 50-mL color-comparison tube dissolve 1.0g ascorbic acid (mol wt 176.12) in 25 mL of water, dilute with water to 40 mL, and mix. Procedure— To each of the two tubes containing the Standard Preparation, the Test Preparation, add 2 mL of pH 3.5 Acetate Buffer, then add 1.2 mL of thioacetamide–glycerin base TS, dilute with water to 50 mL. Mix, allow to stand for 2 minutes, and view downward over a white surface. The color of the solution from the Test Preparation is not darker than that of the solution from the Standard Preparation. The colour is formed when…
11. ● Possible methods for the quantitative determination of sodium bicarbonate for injection are: A) Acidimetry B) Alkalimetry C) Complexometry D) Iodometry E) Refractometry ● Calcium chloride is available in dosage forms: A) Powder for preparation of injections B) Solution for injection 10% in ampoules C) Tablets of 0.3 g D) Solution for injection 25% in ampoules E) Dry dosed powder
explain the results of this experiment Table 1 Absorption Spectrum of Cobalt Chloride Using a Spectrophotometer Wavelength Absorbance 400 410 420 430 440 450 460 370 480 490 500 510 520 530 540 550 560 570 580 590 600 610 620 630 640 650 660 670 680 690 700 0.036 0.044 0.063 0.095 0.147 0.215 0.284 0.329 0.362 0.402 0.450 0.479 0.464 0.398 0.314 0.216 0.142 0.087 0.054 0.041 0.036 0.036 0.034 0.028 0.030 0.023 0.023 0.023 0.014 0.014 0.011 Test Tube Number Cobalt Chloride Concentration (mol/mL) Absorbance at 510 nm 1 0.000 0.000 2 0.009 0.042 3 0.018 0.92 4 0.027 0.139 5 6 0.036 0.045 0.190 0.236 7 (Unknown) 0.151
What is the chemistry principle behind when (treatment: heavy cream) is subjected to room temperature? Why does beating time, stability (%drain) and volume foam (specific gravity) is important? see the data below Treatment (Heavy Cream) Beating Time (min) Stability (%drain) Volume of Foam (Specific Gravity) (Room Temperature) 20 No drain 0.94 Heavy Cream (chilled) 20 No drain 0.76 Heavy Cream with sugar and vanilla 20 No drain 0.88 Heavy Cream (over-whipped) 25 No drain 0.83
In this question, you need to discuss the results you obtained from the BSA standards to generate your standard curve. Are you confident in the absorbance values you measured from the BSA standards? Was there variability between your duplicates? Comment on the shape of your standard curve and note the highest absorbance you would consider for interpolating the concentration of an unknown sample.
By applying Gravimetry, Titration (Chemical indicator) and Potentiometry lessons which technique should be used in following situations. Explain your answer. In your explanation, state what is the advantage of the technique you chose over other technique and /or the barrier/difficulty of using the technique. Your choice should not be dependent on cost. For chem students- Total Acid content per tablet of a newly developed drug that has yellow coating Target level is 1%.