Give the suitable dimensions of a leather open flat-belt system according to the standards having the following details: the source power is 28 Hp. @500 rpm. The driver shaft is 300 mm diameter. The velocity ratio is 1:2.8. The belt material may be cotton woven and the pulleys are rubber faced. The center distance is 3m, take the allowable stress intensity for leather belt is 4.8 MPa. Take safety factor of 1.5.

Give the suitable dimensions of a leather open flat-belt system according to the standards having the following details: the source power is 28 Hp. @500 rpm. The driver shaft is 300 mm diameter. The velocity ratio is 1:2.8. The belt material may be cotton woven and the pulleys are rubber faced. The center distance is 3m, take the allowable stress intensity for leather belt is 4.8 MPa. Take safety factor of 1.5.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6. Design a clamp coupling for transmitting 36 kW, at 200 rpm. Allowable shear stress in shaft is 45 MPa, allowable shear stress in key is 40 MPa, and allowable crushing stress in key is 90 MPa. The number of bolts joining the two halves is 4. The permissible tensile stress in bolts is 60 MPa. The coefficient of friction between the muff and shaft can be taken as 0.25
A belt conveyor transports 18 tonnes per hr at 20°. Determine the speed reducer power factor to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, plain chain drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
The shaft of a belt drive is made of AISI C1020 as rolled steel. The belt tensions vary continuously during transmission at a constant tension ratio of 3:1; the maximum tight side tension being 400 lb and the minimum tight side tension is expected to be 160 lb, at a pulley diameter of 12 inches. For a Goodman factor of safety of 1.8, recommend the diameter of the shaft. Consider a machined surface and the effect of a hardened profile keyway in the shaft.
A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16 inches thick and 10 inches wide is used. The diameters of the motor pulley and the driven pulley are 14 inches and 54 inches, respectively. The center distance is 54 inches and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress of the belt is 350 psi and the belt weighs 0.035 lb/in^3. What is the horsepower capacity of the belt?
3.A chain drive using bush roller chain transmits 5.6 kW of power. The driving shaft on an electric motor runs at 1440 r.p.m. and velocity ratio is 5. The centre distance of the drive is restricted to 550 ± 2% mm and allowable pressure on the pivot joint is not to exceed 10 N/mm2. The drive is required to operate continuously with periodic lubrication and driven machine is such that load can be regarded as fairly constant with jerk and impact. Design the chain drive by calculating leading dimensions, number of teeth on the sprocket and specify the breaking strength of the chain. Assume a factor of
A double-threaded power screw is used to raise a load of 5 kN. The nominal diameter is 60 mm and pitch is 9 mm. The threads are Acme type (20.15. Neglect collar friction, calculate :(a) the torque required to raise the load(b) the torque required to lower the load (c) the efficiency of the screw for lifting load
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
The coefficient of friction of a disk clutch with two pairs of contact surfaces is 0.25. The maximum pressure under working conditions is 220kPa only. The clutch is used to connect two 25mm solid shafts with allowable shearing stress of 69 MPa. The inner and outer diameter of the clutch face is 60 mm and 120mm, respectively. What is the power in kW transmitted at 1000 rpm?
n Mukwano Industries, a shaft assembly shown in Fig. 2 is driven by a flat belt at location A and drives a flat belt at location B. The drive belt pulley diameter is 300 mm; the driven belt pulley diameter is 500 mm. The distance between sheaves is 800 mm, and the distance from each sheave to the nearest bearing is 200 mm. The belts are horizontal and load the shaft in opposite directions. Determine the size of the shaft using Distortion Energy Theory (DET) and the types of steel that should be used. Use a safety factor of 10. Also, provide a free-body diagram as well as moment and torque diagrams
4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt