MIPS ISA has registers of 32-bits which are employed to create a 64-bit base address which is especially used for instructions like Load Word and Store Word. May these Load Word and Store Word instruction formats contain a random pair of source registers to create the base addres

MIPS ISA has registers of 32-bits which are employed to create a 64-bit base address which is especially used for instructions like Load Word and Store Word. May these Load Word and Store Word instruction formats contain a random pair of source registers to create the base addres

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 15VE: A(n) ________________ instruction always alters the instruction execution sequence. A(n)...

See similar textbooks

Related questions

Q: On a typical microprocessor, a distinct I/O address is used to refer to the I/O data reg- isters and…

A: There are two I/O instruction formats utilized in the Intel 8088. In one format, an 8-bit port…

Q: Let us assume we have a CPU which supports both 3-address and 2-address instruction. The length of…

A: 3 address: Three-address instruction is a format of machine instruction. It has one opcode and…

Q: The register content for an Intel 8086 microprocessor is as follows: CS = 1000H, DS = 2000H, SS =…

A: The register contents of 8086 microprocessor are given. a)MOV [SI],AL In this instruction the…

Q: Consider the architecture as shown and the following instruction: link a6, #-8 Internal bus CONTROL…

A: Solutions !!

Q: The register content for an Intel 8086 microprocessor is as follows: CS = 1000H, DS = 2000H, SS =…

A: Given:

Q: The CPU we are talking about today is intel core i7- 8750H 64 bit write in detail about the below…

A: The i7-8750H functions at 2.2 GHz with a TDP of 45 W and a turbo boost of up to 4.1 GHz. This chip…

Q: Q: For a basic computer that is currently running in its timing TO of execution for an instruction…

A: According to the information given:- We have to find the next instruction after end of the…

Q: By using the concept of instruction pipelining imagine instructions are executed in 6 stages namely…

A: There are 5 instructions for execution in both pipelined and non pipelined mode. Each instruction…

Q: The register content for an Intel 8086 microprocessor is as follows: CS = 1000H, DS = 2000H, SS =…

A: Given:

Q: 3. CPU x86/8088 executes the instruction ADD AX, CX; 2byte instruction, machine code is (03-C1).…

A: Answer: I have given answered in the brief explanation

Q: Design a memory system for the 8088 Microprocessor such that it can select two EPROMS (128K x 8)…

Q: is this a computer architecture feature or a computer organization feature? 12 pipeline stages BL…

A: Computer Architecture vs Computer Organization Computer Architecture Computer architecture is a…

Q: What would be the clock period of a pipelined MIPS architecture with two stages, one comprising…

A: What would be the clock period of a pipelined MIPS architecture with two stages, one comprising…

Q: Assume a CPU has 8 registers (3 bits), 32 op-codes (5 bits), 15-bit addresses, 16- bit integers.…

A: An instruction format defines the different component of an instruction. The main components of an…

Q: P. 1. Assume that we would like to expand the RISC-V register file to 128 registers and expane the…

A: The number of instructions is initially somewhere between 25=32 (the number of instructions must be…

Q: Suppose you are designing an instruction set architecture with 16-bit instructions and 26 different…

A: I am providing you 2 answers choose one of them Opcode:- In computing, an opcode (abbreviated from…

Q: A complete 6-stage non-pipelined 16-bit CPU architecture include 6 components: a register file, a…

A: A complete 6-stage non-pipelined 16-bit CPU architecture include 6 components: a register file, a…

Q: Suppose we add the following instruction to MARIE's ISA: Jumpoffset X This instruction will jump to…

A: Register Transfer Notation (RTN is a notation which uses symbols to describe the behavior of micro…

Q: If the opcode field of instructions in a microprocessor's architecture is 16 bits wide, what is the…

A: total possible instruction would be 2n where n is the number of bits in the opcode.

Q: Consider the diagram below that shows the fetching data flow for an indirect cycle along with the…

A: What will be the content of the MAR register after finishing the execution of the indirect cycle for…

Q: The next three questions refer to the following system: A certain ISA has a 32-bit word size, uses…

A: The Answer is

Q: 68000 Question: How does the MC68000 processor differentiate between the two addressing modes:…

A: It is defined as a controlling unit of a micro-computer, fabricated on a small chip capable of…

Q: A certain computer has a memory of 1M words, and each word is 32 bits long. Each instruction is 32…

Q: For a particular computer architecture, the ISA consists of a total of 70 different operations. The…

A: Below is the answer to above question. I hope this will be helpful for you.

Q: Q1:Suppose the initial physical address of a segment register is given by 0E41:A02EH. Determine the…

A: The solution for the above given question is given below:

Q: in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory…

A: Given:- DS = 0200H BX = 0300H DI = 400H

Q: Suppose an instruction takes 6 cycles to execute in an unpipelined CPU: one cycle to fetch the…

A: Actually, the answer has given below:

Q: Assume a CPU has 8 registers (3 bits), 32 op-codes (5 bits), 15-bit addresses, 16- bit integers.…

A: CPU has 8 registers (3 bits), 32 op-codes (5 bits), 15-bit addresses, 16-bit integers. Which ISA…

Q: Compute the binary representation of the following mips instruction: lw $t4, 5($s4)

A: opcode => lw => 100011 base => $s4 => 10100 rt => $t4 => 01100…

Q: A read/write type memory will be designed for a microprocessor with 16 bit address bus.. Memory…

A: A read/write type memory will be designed for a microprocessor with 16 bit address bus.. Memory…

Q: Datapath for the AND Instruction 10 Answer the following questions about this specific instruction:…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Consider the architecture as shown and the following instruction: link a6, #-8 Internal bus CONTROL…

A: Solution !!

Q: For the below microprogrammed architecture, what is the ALU sequence of actions/micro instruction…

A: Solution:-- 1)The given question is an type of the multiple choice question so some of the options…

Q: In the read bus cycle of 8086, the Bus AD0-AD15 is asserts by the MP to end of bus cycle, the…

A: In the read bus cycle of 8086, the Bus AD0-AD15 is asserts by the MP to end of bus cycle, the…

Q: Assume a CPU has 8 registers (3 bits), 32 op-codes (5 bits), 15-bit addresses, 16-bit integers.…

A: ISA: ISA is the part of the processor that is noticeable to the programmer or compiler author. The…

Q: The register content for an Intel 8086 microprocessor is as follows:CS = 1000H, DS = 2000H, SS =…

A: The register contents of 8086 microprocessor are given. a)MOV [SI],AL In this instruction the…

Q: 3. A microprocessor has . .. address bus a. unidirectional b. bi-directional c. Both 4. Instruction…

A: 3. Given that A microprocessor has ................................................ address bus…

Q: Assuming a 500 KHz 6800 microprocessor, the total time (in microseconds) required to execute the…

A: Direct and Extended Addressing Modes In the Direct and Extended modes of addressing, the quantity…

Q: The 5 stages of a processor have the following latencies: Fetch Decode Execute Memory…

Q: The 8086 data bus consists of 8, 16, 1 point or 32 parallel signal lines * O 8, 16, or 32 parallel…

A: 1) Correct Option : First Option 8, 16 or 32 parallel signal lines It consists of 8, 16 or 32…

Q: Q1.1 lw instruction execution. 4 Points With the given MIPS single-cycle CPU schematic, when Iw $8,…

A: We have MIPS Single Cycle Schemetic lw $8 4($9) lw = loads a word into a register $8 = temprary…

Q: Consider two different implementations of the same ISA. The characteristics of each implementation…

A: In the given problem statement, they have provided the two machines instructions and about their…

Q: (b) Consider an ARM CPU that executes its instructions using a simple 3-stage pipeline consisting of…

A: The ARM processor is a family of reduced instruction set computer architectures for computer…

Q: Suppose we add the following instruction to MARIE’s ISA: JumpOffset X This instruction will jump to…

A: Register Transfer Notation (RTN) is a notation that uses symbols to define actions. Micro-operation…

Q: Assume the processor is driven by a clock, such that each control step is 4 ns in duration. How long…

A: Given Data : Control Step time = 4ns Read operation time = 12 ns To find : Percentage of time…

Q: In the MIPS micro-architecture, the PC is incremented for each instruction, during the "Instruction…

A: In MIPS architecture the PC can be updated in two stages: During the Instruction Fetch, the PC is…

Q: MIPS architecture has a register set that consists of 32-bit registers.

A: Answer:- Theoretically, the answer to your question is a resounding "yes". A Turing Machine, the…

Q: 1.An address field in an instruction contains decimal value 24. Where is the corresponding operand…

A: 1.An address field in an instruction contains decimal value 24. Where is the corresponding operand…

Concept explainers

Fundamentals of Input and Output Performance

The I/O subsystem is a component of computer system design that uses buses to assist communication between the Central Processing Unit, Computer Memory/Storage, and Input and Output Devices (that is known as peripheral devices). The I/O subsystem includes disc controllers, tape drives, discs, system buses, and other devices. The I/O database application reads and writes drives using the operating system windows I/O.

Question

If yes, explain if there will be any corresponding effects and what they will be?

If no, why not?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Fundamentals of Input and Output Performance

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
A(n) ____________________ instruction copies data from one memory location to another.
How does pipelining improve CPU efficiency? What’s the potential effect on pipelining’s efficiency when executing a conditional BRANCH instruction? What techniques can be used to make pipelining more efficient when executing conditional BRANCH instructions?
How can I compute sum of each of the component latencies for each instruction? Question 1: This is a three-part question about critical path calculation. Consider a simple single-cycle implementation of LEGv8 ISA. The operation times for the major functional components for this machine are as follows: Component Latency ALU 90 ps Add 70 ps ALU Control Unit 30 ps Shifter 20 ps Control Unit/ROM 50 ps Sign/zero extender 20 ps 2-1 MUX 20 ps Memory (read/write) (instruction or data) 140 ps PC Register (read action) 20 ps PC Register (write action) 20 ps Register file (read action) 80 ps Register file (write action) 60 ps Logic (1 or more levels of gates) 10 ps Below is a copy of the LEGv8 single-cycle data path design. In this implementation the clock cycle is determined by the longest possible path in the machine. The critical paths for the different instruction types that need to be considered are:…
in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory address accessed by each of the following instructions, assuming real mode operation: (1) MOV AL,[1234H] (2) MOV AX,[BX] (3) MOV [DI]AL
In the MIPS micro-architecture, the PC is incremented for each instruction, during the "Instruction Fetch" stage. The value of the PC may also be updated later within the "Memory Access" phase. * If the value of the PC is: 0x0000 2F1C, what is the value of the PC after you complete the execution of the instruction: ``addi $t0, $s0, $ra``?* 
If the opcode field of instructions in a microprocessor's architecture is 16 bits wide, what is the maximum number of distinct instructions possible in that ISA? Group of answer choices 65536 16 9999999999999999 4
An 'instruction fetch/read' results in three sets of numbers that go to the Registers Block as studied in class. These three numbers in the instruction represent bits 25-21 for 'Read Register 1', bits 20-16 for 'Read Register 2', and bits 15-11 for the 'Write Register'. What does the 5 bits width of each of these indicate? a. That the word is 15 bits long in this architecture b. That each word is 32 bits long c. That there are 32 registers that can be addressed in this architecture d. That there are 15 registers that can be addressed in this architecture
Let us assume that we would like to design an ISA R-format instruction format for a processor. The processor has 256 registers and 64 opcodes. The R-format has four fields, the opcode and three fields for the registers. Show the instruction format and the bit allocation for each field.
Consider a word-addressable computer with 32 bits per word. The instruction set consists of 30 different All instructions have an operation code field, a mode field to specify one of 7 possible addressing modes, a register address field to specify one of 60 available registers, and a memory address field. Each instruction is stored in one word of memory. What is the maximum allowable size for memory? Use KB, MB, or GB as a unit.
Suppose we add the following instruction to MARIE’s ISA:This instruction increments the value with effective address “Operand,” and if this newly incremented value is equal to 0, the program counter is incremented by 1. Basically, we are incrementing the operand, and if this new value is equal to 0, we skip the next instruction. Show how this instruction would be executed using RTN.