Q1: Draw the circuit of full wave rectifier mentioned on the circuit all equipment requirements to measure input and output voltages and the circuit current take in consideration voltage source 100v rms and load of 15k2 and device required to draw output signal, find the following: a. Calculate output current and voltages. b. Find input and output powers and the efficiency. c. Draw input and output voltages and output currents mentioned the amplitudes. d. What is the PIV of full wave bridge rectifier? And how many types of full wave rectifiers?

Q1: Draw the circuit of full wave rectifier mentioned on the circuit all equipment requirements to measure input and output voltages and the circuit current take in consideration voltage source 100v rms and load of 15k2 and device required to draw output signal, find the following: a. Calculate output current and voltages. b. Find input and output powers and the efficiency. c. Draw input and output voltages and output currents mentioned the amplitudes. d. What is the PIV of full wave bridge rectifier? And how many types of full wave rectifiers?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

What is CEMF?
The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
What is the difference between a diode and rectifier?
How is a solid-state diode tested? Explain.
(Q1 ,b) Required Explain the applications-based comparison b/w FWBR & CT-FWR so that under what conditions you will choose the CTWR.? b. Interpret (using the circuit diagram & the waveform diagrams) the behavior of a controlled Half-Wave Rectifier during the negative half cycle of AC supply when it is connected with RL load in the following cases; a. Without Free-wheeling diode.
Q.1 A single-phase diode bridge rectifier is connected to a grid with rms voltage V, 230V at 50 Hz. Assume that the load is highly inductive, so it could be represented by a constant dc current, Id = 10A. a) Sketch the load voltage and find the average voltage of the load? b) Sketch the source current (grid. AC side) and find the rms value of the source current? c) Determine the fundamental source current and the first three harmonics? Assume Ish_rms ³ 0.91a/h for odd hand 0 otherwise?
A single-phase fully controlled, full-wave, bridge rectifier has a source of 230 V rms at 50 Hz, and is feeding a load R = 25 and L = 10 mH. The firing angle α = 45˚ and the current extinction angle β =230˚. It is required to: (a) Sketch the appropriate load voltage and load current waveforms. (b) Determine whether the current is continuous or discontinuous. (d) Determine the average load voltage and current. (e) Determine the rms load voltage and current. (f) Determine the a.c. and d.c powers absorbed by the load. (g) Determine the efficiency of the converter.
(1) Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor. (2).Sketch the ac supply voltage and the voltage across the resistive load in (question no 1)indicating the period of the resistive load voltage. (3) For the circuit in (question no 1) calculate the average and rms voltages across the resistive load for an rms ac supply voltage of 115 V assuming no diode voltage.
Consider a three-phase diode rectifier supplying a R = 10 Ω DC load. The supply systemis 440 VLL and 60 Hz. A) What is the value of the average (DC) current across the load?B) Compute the value of an inductive filter (L) to be added in series with the resistiveload to limit the rms value of the lowest order current harmonic to 1% of the DC currentvalue. Note: 2 /[( 1)( 1)] Vdch = Vdc0 h − h + (in rms).
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
Find the performance parameters (FF, RF and n) for the Single phase bridge uncontrolled rectifier with RL load. If the phase voltage: Vph(t) = Vm sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms.
For the Zener regulated power supply a shown, the rms value of vI is 15V, the operating frequency is 60Hz, R =100Ω, C =1000μF, the on voltage of diodes D1 and D2 is 0.75V, and the Zener voltage of diode D3 is 15V.(a)What type of rectiﬁer is used in this power supply circuit?(b) What is the dc voltage at V1? (c) What is the dc output voltage VO?(d)What is the magnitude of the ripple voltage at V1? (e) What is the minimum PIV rating for the rectiﬁer diodes? (f) Draw a new version of the circuit that will produce an output voltage of−15 V.