Solid and hollow shafts are most often used to provide power transmission of the rotating motion from the power source/engine to the car's wheels. In car manufacturing factory, your role is to determine the distribution of shear stress and the angular deflection due to predefined applied torsions to analyses and investigate the minimum and maximum stresses generated in the shafts. Considering the shaft in Figure.1, including a hollow part AB and solid part BC, your manger asked you to perform the following tasks: 1- The maximum and minimum shearing stress in shaft AB, if the outer diameter is 85 mm. 2- Sketch the distribution of the shear stress due to torsion in shaft AB. (simple sketch of shear stress "t" vs. shaft radius "p" for the elastics region) 3- Make a simple sketch the distribution of the angular deflection due to torsion in shaft AB. (simple sketch of torsion "T" vs. angle of twist "Q" for the elastics region) d. 71 mm 10 kN-m A 5 kN-m B.

Solid and hollow shafts are most often used to provide power transmission of the rotating motion from the power source/engine to the car's wheels. In car manufacturing factory, your role is to determine the distribution of shear stress and the angular deflection due to predefined applied torsions to analyses and investigate the minimum and maximum stresses generated in the shafts. Considering the shaft in Figure.1, including a hollow part AB and solid part BC, your manger asked you to perform the following tasks: 1- The maximum and minimum shearing stress in shaft AB, if the outer diameter is 85 mm. 2- Sketch the distribution of the shear stress due to torsion in shaft AB. (simple sketch of shear stress "t" vs. shaft radius "p" for the elastics region) 3- Make a simple sketch the distribution of the angular deflection due to torsion in shaft AB. (simple sketch of torsion "T" vs. angle of twist "Q" for the elastics region) d. 71 mm 10 kN-m A 5 kN-m B.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft 450 mm diameter supports a 15000 kg steel propeller of the ship. The propeller shaft can be considered as a cantilever of 2 m length with a concentrated load at the end. The propeller is driven at 100 rpm when speed of the ship is 17.2 Knots. If the engine develops 15 MW and the propulsion efficiency is 85 %, calculate the principal stresses and the Maximum shear stress in the shaft and hence determine the factor of safety based on Max. shear stress and distortion energy theories if the shaft is made of steel having yield strength = 380 MPa. Given 1 knot = 1852 m/hr., sea water density = 1.1g/ml
Example 10.11 The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
I solved the principal stresses but having a hard time on determing the theta-P (orientation of principla plances), could you help me?
A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 90⁰ with respect to the other end without exceeding an allowable shear stress of 300 MPa?
Sketch a tensile member with (a) a rectangular crosssection, (b) a solid circular cross section, and (c) a circulartubecross section, and label the dimensions symbolically (e.g.,label the radius for the solid circular case). For each member, write out the definition of engineering stress in terms of the actual dimensions of the component. If therectangular member has dimensions of width and thicknessequal to 1 cm 0.3 cm, what would be the radius of a solidcircular member such that the stress is equal for an equaltensile load? If a tube has an outer radius equal to that ofthis same solid cylinder, what is the maximum inner radiussuch that the stress does not exceed 200% of the stress inthe solid cylinder?
On Page765,consider Figure11.11 where a force P is axially applied.On Page 768, considerFigure 11.18, wherea torque T is applied as shown.Combine these structures into one system, which issimultaneously subjected to the force P and the torque T.Analyze this new system,and comment on (a) the relative strengths of the strain energies due to F andT; (b) the impact of n; and (c)any other important engineering observations you can make regarding the new system
A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by auniaxial tensile load of 4800 N in 120 seconds. At this load, the length of therod is measured as 49,2 mm. Calculate the followings:(a) Stress and strain occurred on the rod at this load.(b) Initial strain rate.(c) Diameter of the rod at this load.(Yield strength : 380 MPa, Ultimate Tensile Strength: 670 MPa,Modulus of Elasticity: 210000 MPa were given for this material)
Consider a hollow steel shaft with a 130mm outside diameter and a 70mm inside diameter. What is the maximum torque that this shaft can transmit if the shear yield stress is 1.4 x 108Pa and the behavior is elastic, perfectly plastic?
An automotive shaft manufacturing facility wants to reduce the material cost of the shaft.Propose a shaft design to minimize the material consumption, keeping in view that themaximum shear stress occurs at the outermost edge of the shaft.
A hollow steel shaft is to transmit 5,605 N·m of torque and is to be sized so that the torsional stress does not exceed 151 MPa. If the inside diameter is three-fourths of the outside diameter, what is the exact outside diameter size of the shaft in mm?
What is the magnitude of shear stress generated in shaft of diameter 20 mm when 10 Nm torque is applied on it.
For a given material, Young’s modulus is 100GPa and shear modulus is 40GPa. Find the bulk modulus and lateral contraction of a round bar of 40mm diameter and 2.5 m long when stretched 2.5 mm.