What is the absolute uncertainty in the concentration of the diluted solution? 0.363 (10.004 ) Mx15.00 (20.03) mL = 0.054 45M (unrounded) 100.00 (10.08) ml A. +0.01 M B. 10.000 6 M C. 10.004 M D. 10.09 M E. 10.000 01 M

What is the absolute uncertainty in the concentration of the diluted solution? 0.363 (10.004 ) Mx15.00 (20.03) mL = 0.054 45M (unrounded) 100.00 (10.08) ml A. +0.01 M B. 10.000 6 M C. 10.004 M D. 10.09 M E. 10.000 01 M

Fundamentals Of Analytical Chemistry

9th Edition

ISBN:9781285640686

Author:Skoog

Publisher:Skoog

Chapter7: Statistical Data Treatment And Evaluation

Section: Chapter Questions

Problem 7.13QAP

See similar textbooks

Related questions

Q: Chromatography is done on a mixture containing a drug. The drug has an R value of 0.66. The diagram…

A: The question is based on the concept of chromatography technique. Rf value is defined as the ratio…

Q: Two different laboratories within a company further studied the morantel recovery percentage in…

A: Given data:

Q: ou collected the following data from a titration experiment using a 0.118M standardized NaOH…

A: The reaction taking place between standardized NaOH and H2SO4 is - H2SO4 + 2NaOH→Na2SO4 + 2H2O Thus,…

Q: Determine the percentage error and the concentration of the prepared NaOH given the following data.…

A: Answer: This is the question based on acid-base titration where with the of KHP data we have to find…

Q: Table 1: 田 Average [NaOH) (M) Volume NaoH [NaOH) (M) Trial # KHP (g) (ml) 0.4510 22.16 0.4524 22.21…

A: The table gives mass of KHP (potassium hydrogen phthalate) and different volume of NaOH. To find:…

Q: The 95 % confidence limit for Zn in certain water sample is 2.90± 0.25 mg/L. Circle the correct…

Q: You have a stock solution certified by a manufacturer to contain 225.0 ± 0.4 ug SO-/mL. You would…

A: Method A: Dilute 10.00 mL upto 100 mL with a transfer pipet and volumetric flask. Then take 10.00 mL…

Q: How many mL of 0.625 M KBr are needed to prepare 2.50L of 0.0500 M KBr? A) 31.3 mL B) 0.0200 mL C)…

A: Which one of the following is correct answer

Q: A calibration curve of KCl conductivity (y-axis) vs concentration (mass percent, x-axis) is made.…

A: Given data: Equation of line: y = 578.3x + 0.380 y-axis contains conductivity values and x-axis…

Q: Determine the percentage error and the concentration of the prepared NAOH given the following data.…

A: Given: NNaOH true = 0.045 N And the experiment data is,

Q: Determine the percentage error and the concentration of the prepared NaOH given the following data.…

A: Given data - NNaOHtrue = 0.045N Weight of KHP = 0.2503g For trial -1Vf NaOH= 25mlVi NaOH = 0mlFor…

Q: Determine the percentage error and the concentration of the prepared NaOH given the following data.…

Q: In a gravimetric chloride analysis, it was found that 0.82g AgCl and 0.80g AgCl was obtained from an…

A: Moles = mass / molecular mass molecular mass of AgCl = 108 + 35.5 = 143.5 => moles of AgCl in…

Q: Table 1: Estimation of Dissolved Oxygen: SI No Volume of water Initial sample (ml) burette Final…

A: Dissolved Oxygen is defined as the amount of gaseous Oxygen that is dissolved in the water .…

Q: Seoyeon needs to prepare a 250 mL solution of 0.1000 M Na2CO3. Which glassware should she use to…

A: All the instruments mentioned can be used to measure the volume of the solution. Although for…

Q: In order to form Ba(IO3)2, 500 mL of 0.5000 M Ba(NO3)2 was mixed with 500 mL of 0.0500 M NaIO3.…

A: We have to find out the millimoles of NaIO3 are there in the solution

Q: 15. Calculate the mass of Cefaclor (purity 95% w/w) needed to prepare 250 ml of 500 ppm (w/V)…

A: Please find the attached solution below

Q: Using M1V1=M2V2 Make 100ml of a solution that contains 0.5mM MgCl2, 15 mM CaCl2 and 120 mM KCl 0.5M…

A: Molarity is defined as “the mole of the solute per unit volume of the solution”. It is represented…

Q: You are given a standard with a concentration of 10 ppm. You are to create 5 different samples, all…

A: Concentration of the standard = 10 ppmTotal volume of each sample = 100 mLWe have to solve the…

Q: 19 g of unknown organic sample was dissolve in 640 mL of Dicloromethane (DCM). The boiling point of…

Q: -1 Measurements shown that the concentration of salt in seawater is 35.5 g-L .C recover 0.100 kg of…

A: Given: density of seawater = 35.5 g/L Mass of salt to be recovered = 0.1 Kg To calculate: volume…

Q: 6) 100.01 mg Cu(NO3)2 is diluted to 100.00 mL with distilled water. Calculate the ppm of the…

A: GIVEN: Mass of Cu(NO3)2 is = 100.01 mg Volume of distilled water = 100.00 mL = 0.100 L Uncertainty…

Q: Write each answer with the correct number of digits. a. 1.021 + 2.69 b. 4.34 x 9.20 c.…

A: Since you are posted with multiple sub-parts. As per the rule, I am answering the first three…

Q: f 55mg of CaC2O4 is placed in a 250mL pack of H2O nanopure at 25 celcius, how much (in mg) of CaC2O4…

A: Solubility is defined as the maximum amount of solute that can be dissolved in a solvent at…

Q: A lab pair’s Beer’s Law calibration graph 0.08 < A < 0.79 had a best-fit line of A = 0.013 C –…

Q: During lab, a student used a Mohr pipet to add the following solutions into a 25 mL volumetric…

A: Solutions concentration get altered on dilution, but the solutes moles initially present remains…

Q: The student collected the following data he prepared solutions ranging from 0.000 to 0.500 ppm and…

A: We have to find first equation for given points and then we have to find amount of unknown using…

Q: Using the linear regression equation on the previous question, what is the concentration of the…

A: Given

Q: Estimate the value of the equilibrium constant Kc for the reaction below from the data in the graph.…

A: Given,[O2] = 0.750M[NO2] = 0.600M[NO] = 0.400M

Q: AP Question // Q 5) Using the graph below, find the slope (and its unit). What letter(s) the Beer's…

A: In order to find the slope, we have to draw a linear regression plot in an excel file and using the…

Q: What is the molarity of the caffeine solution B? Molecular Weight of Caffeine 1942 grmol A Take 20…

A: Given, Note: 1000 mL = 1 L Solution A Molarity of the solution A = 5 × 10-4 M = 5 × 10-4 mol/L…

Q: Table 5: Data for Trial 3 Water displaced in mL 2 mL Time (seconds) 53 4 mL 100 6 mL 139 8 mL 178 10…

A: The order of the reaction is the sum of the exponents of the concentration terms in the…

Q: 8. A student made a series of measurements of Mg** concentration in drinking water giving the…

A: Introduction : Drinking water contains magnesium high concentration of magnesium and sulfur is…

Q: A pipet delivers 10.9 mLmL , 10.1 mLmL , and 10.9 mLmL in consecutive trials. Find the mean volume…

Q: 18 g of unknown organic sample was dissolve in 758 mL of Dicloromethane (DCM). The boiling point of…

Q: Calculate the volume of a 0.01 M potassium permanganate (KMnO4) solution that you need to prepare 25…

Q: Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were…

A: 1)The null and alternate hypothesis are: H0= (the analysis is accurate ) H1= (the analysis is not…

Q: Solid calcium carbonate, CaCO3, was added to a solution of pure water. Analysis found 1.20*10-3 M…

Q: STANDARD SAMPLE PREPARATIONS FOR ABSORBANCE & CONCENTRATION DATA Concentration of stock nickel…

A: In order to solve this table and find molarities/concentrations, we will use the law of dilution…

Q: 17 g of unknown organic sample was dissolve in 564 mL of Dicloromethane (DCM). The boiling point of…

A: NOTE: It will be benzene only and not DCM as the data is given for benzene and there is a typo error…

Q: A 10 ml of concentrated acetic acid was added in a sufficient quantity of water to make 350 ml of…

Q: Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were…

A: 1)The null and alterate hypothesis are: H0= (the analysis is accurate ) H1= (the analysis is not…

Q: a. Convert 52.6 mM (millimolar) to μM (micromolar) and to M (molar). b. Convert 200.0 μM to mM…

Q: A bubble of air escaping from a diver’s mask rises from a depth of 124 ft to the surface where the…

A: Given, Depth of the driver"s mask = 124 ft surface pressure = 1.00 atm volume of bubble = 10.0 mL…

Q: 9. The concentration of a solution (in ppb) was measured several times, resulting in the following…

A: Given : Concentration in ppb 7.45 8.49 6.91 7.32 The Accepted value for the…

Q: You have a stock solution certified by a manufacturer to contain 220.0 + 0.4 ug So /ml. You would…

A: Method A: Dilution of 10.00 mL (transfer pipet) 215.0 g/mL stock solution to 100 mL (vloumetric…

Q: Final Serum Diluted Test Tube No. Normal Initial New NSS Dilution (mL) Saline (NSS) Dilution (ID) |…

A: Concentration of the substance is a quantification of amount of solute present in a solution with…

Q: A- STANDARD PHOSPHATE SOLUTION: Standard solution 1 4 6. Conc of PO4 (ppm) O-00 O.2 0.4 0.6 0.8 1-0…

A: Calculations: Q.1: In order to find the ppm of phosphate in the unknown water sample, we have to…

Q: burette reading

Concept explainers

Analytical Tools

Analytical tools or analysis tools help one to get into a conclusion or results from the data collected. Analytical tools can be applied for simple data sets and also in the case of big data analytics.

Question

100%

What is the bsolute uncertainty in the concentration of the diluted solution?
0.363 (10.004) Mx15.00 (20.03) mL
= 0.054 45M (unrounded)
100.00 (20.08) mL
A. +0.01 M
B. 10.000 6 M
C. 10.004 M
D. 10.09 M
E. 10.000 01 M

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Analysis

VIEW

Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, chemistry and related others by exploring similar questions and additional content below.

Similar questions

Beaker 0.00200 M Fe(NO3)3, mL 0.00200 M NaSCN, mL total volume, mL 1 3.000 2.000 10.00 2 3.000 3.000 10.00 3 3.000 4.000 10.00 4 3.000 5.000 10.00 5 (blank) 3.000 0.000 10.00 In Solutions 1-4 you are adding successively larger volumes of 0.00200M SCN- to the Fe3+ solution and diluting to 10.00 ml. Calculate the final diluted molarity of SCN- in solution #1 Your answer should have 3 sig figs =
If exactly 200.0 mL of an aqueous solution that is 1.037E3 ppb Pb(NO3)2 (331.2 g/mol) is mixed with 100.0 mL of an aqueous solution that is 3.090E9 fM KI (166.00 g/mol), how many micrograms of solid PbI2 (461.01 g/mol, 6.16 g/mL) are formed? Assume complete reaction.
Table of caffeine standards concentration . Sample Conc, ppm Std1 16 Std2 32 Std3 48 Std4 64 Std5 80 If the volume used to make 100 mL of std 1 is 2 uL what is the concentration in M used to make std calibration curve ? The standards are going to be used to build calibration curve to analyze caffeine in an energy drink. if 500 mL of the energy drink has target of 400 mg , how will you prepare the sample if you need 10 mL for the analysis ? Caffeine MM=194.19 g/mol.
When drinking water is disinfected with chlorine, an undesired byproduct, chloroform (CHCl3), may form. Suppose a 70-kg person drinks 2 L of water every day for 70 years with a chloroform concentration of 0.08 mg/L (the drinking water standard). Potency factor for chloroform = 6.1 x 10-3 (mg/kg-day)-1 The upper-bound cancer risk for this individual. a. 0.545 b. 5.45x10-6 c. 5.45x10-4 d. 5.45x10-10 e. 14x10-6 If a city with 300,000 people in it also drinks the same amount water described in the above question, how many extra cancers per year would be expected? Assume the standard 70-year lifetime. a. 0.163 b. 1.63x10-4 c. 1.63x10-3 d. 1.63x10-6 e. 6x10-2
19 g of unknown organic sample was dissolve in 640 mL of Dicloromethane (DCM). The boiling point of benzene was increased by 3.78oC. Determine the molecular weight of the unknown sample? Kb of DCM = 2.42oC/m Bb of benzene = 39.6 oC density of benzene = 1.33 g/mL at 25 °C Round your answer to the nearest whole number, no units required.
6) 100.01 mg Cu(NO3)2 is diluted to 100.00 mL with distilled water. Calculate the ppm of the resulting solution and also calculate the uncertainty of the result. Report the result with the suitable number of significant figures (the uncertainty of 100.00 mL capacity volumetric flask is 0.07 mL, the uncertainty coming from the weighing is 0.05 mg).
An analysis of city drinking water for total hardness was done by two students in the laboratory and produced the following results (in ppm CaCO3): Student A: 228.3, 226.4, 226.9, 227.1, and 228.6. Student B: 229.5, 226.1, 230.7, 223.8, and 227.5What is the 95% confidence interval for the mean?
You determine the acetic acid (HOAc) content of vinegar by titrating with a sodium hydroxide standard solution to a phenolphthalein (an indicator) end point. An approximately 5-mL sample of vinegar is weighed on an analytical balance in a weighing boat and this is found to be 5.0268 g. The standard deviation in making a single weighing is 0.2 mg. The sodium hydroxide must be accurately standardised (this means its concentration must be accurately determined) by titrating known mass of high-purity potassium hydrogen phthalate, and three such titrations give molar concentrations of 0.1167, 0.1163 and 0.1164 mol L-1. A volume of 36.78 mL of sodium hydroxide is used to titrate each sample. The standard deviation of the burette used is 0.02 mL. Calculate the percentage of acetic acid in the vinegar and its standard deviation.
The analysis shows different concentrations based on replicate determinations of Zn in a water sample: 0.754 mg, 0.721 mg, 0.734 mg, 0.731 mg and 0.742 mg. What is the absolute error if the standard solution has 0.750 mg of Zn?
In the determination of the concentration of chloride ion in water five experiments were done: 254.3 ppm, 254.7 ppm, 249.9 ppm, 252.5 ppm, and 253.4 ppm. What is the relative average deviation of this experiment? (ppm=mg/L
What is the CV of the data below? 2.7 ppm, 3.0 ppm, 2.6 ppm, 2.8 ppm, and 3.2 ppm
I would need help with these questions. The method referenced above was followed by a student and she got the following results: Caffeine Std. Conc. (ppm) Absorbance 100 1.806 50 0.899 40 0.724 30 0.545 20 0.365 10 0.183 Further, she analyzed an unknown sample and she got the following results: Sample # Absorbance 1 0.398 1. Graphically find the concentration in ppm and then calculate in mol/L of Caffeine in Sample #1? 2. Which solvent was used to extract Caffeine and why? Why is it necessary to do extraction three times? 3. Cuvettes used in this experiment were made from which material and why? 4. At what wavelength the Absorbance was measured?