If the volume used to make 100 mL of std 1 is 2 uL what is the concentration in M used to make std calibration curve ? The standards are going to be used to build calibration curve to analyze caffeine in an energy drink. if 500 mL of the energy drink has target of 400 mg , how will you prepare the sample if you need 10 mL for the analysis ?

If the volume used to make 100 mL of std 1 is 2 uL what is the concentration in M used to make std calibration curve ? The standards are going to be used to build calibration curve to analyze caffeine in an energy drink. if 500 mL of the energy drink has target of 400 mg , how will you prepare the sample if you need 10 mL for the analysis ?

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter3: Statistical Tests With Excel

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

I would need help with these questions. The method referenced above was followed by a student and she got the following results: Caffeine Std. Conc. (ppm) Absorbance 100 1.806 50 0.899 40 0.724 30 0.545 20 0.365 10 0.183 Further, she analyzed an unknown sample and she got the following results: Sample # Absorbance 1 0.398 1. Graphically find the concentration in ppm and then calculate in mol/L of Caffeine in Sample #1? 2. Which solvent was used to extract Caffeine and why? Why is it necessary to do extraction three times? 3. Cuvettes used in this experiment were made from which material and why? 4. At what wavelength the Absorbance was measured?
Standardization of Sodium Thiosulfate Solution Primary Standard used: Potassium Dichromate Formula mass of 1o standard: __________________ % Purity of 1o standard: 99.80% Trials 1 2 3 Weight of K2Cr2O7 (g)Weight of K2Cr2O7 (g) 0.0315 0.0331 0.0380 Final Volume Reading Na2S2O3 (ml) 27.50 27.50 34.90 Initial Volume Reading Na2S2O3 (ml) 1.10 0.00 1.00 Net Volume Na2S2O3 used (ml) Molarity of Na2S2O3
An analysis of city drinking water for total hardness was done by two students in the laboratory and produced the following results (in ppm CaCO3): Student A: 228.3, 226.4, 226.9, 227.1, and 228.6. Student B: 229.5, 226.1, 230.7, 223.8, and 227.5What is the 95% confidence interval for the mean?
A 50.00 (±0.03) mL portion of an HCl solution required 29.71(±0.03) mL of 0.01963(±0.0030) M Ba(OH)2 to reach an end point with bromocresol green indicator. The molar concentration of the HCl is calculated using the equation below (attached image): a.) Calculate the uncertainty of the result (absolute error). M=0.02333(±?????) M b.) Calculate the coefficient of variation for the result. CV= (Sy/y) x 100%
The gravimetric factor used to express CoCBr6·H20 in a sample that is finally weighed as PbClBr is choose below: FW PbClBr / 6 x FW CoCBr6·H20 FW CoCBr6·H20 / FW PbClBr FW CoCBr6·H20 / 6 x FW PbClBr 6 x FW PbClBr / FW CoCBr6·H20
5. A new method for measuring NO2 in air was developed and compared to a conventional method with the results summarized in the following table: Method Average concentration (ppb) Standard deviation (ppb) Number of measurementsConventional 56.0 3.1 7New 51.9 2.8 8 a) Is the standard deviation for the new method significantly different from that of the conventional method? b) Does the new method give an average concentration similar to the conventional method at the 95% confidence level?
Analysis was run on samples from a known CRM with 8.85% Fe. The following results for %Fe were obtained by an analyst: 8.75, 8.51, 8.25, 8.61. Which of the following statements is true assuming none of the data points are outliers? Group of answer choices Tcalc = 63.15 The analysis is not accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is accurate at the 95% confidence interval. Not enough information to determine Tcalc = 63.15 The analysis is accurate at the 95% confidence interval. Tcalc = 3.03 The analysis is not accurate at the 95% confidence interval.
Density of solution:Trial 1: 1.2 g/mLTrial 2: 1.2 g/mLTrial 3: 1.2 g/mL Average density = 1.2 g/mL What is the relative average deviaion, %?
A pipet delivers 10.9 mLmL , 10.1 mLmL , and 10.9 mLmL in consecutive trials. Find the mean volume of the samples. = Answer = 10.6 mL Part B What is the average deviation from the mean for the above samples?
To determine the organic material in a dried lake bed, the percent carbon by mass is measured at two different locations. To compare the means of the two different locations, it must first be determined whether the standard deviations of the two locations are different. Location 1 Standard deviation = 0.050 Location 2 standard deviation = 0.34 a) What is the calculated ? value for comparing the standard deviations? Fcalc = __________________
To determine the organic material in a dried lake bed, the percent carbon by mass is measured at two different locations. To compare the means of the two different locations, it must first be determined whether the standard deviations of the two locations are different. For each location, calculate the standard deviation and report it with two significant figures. What is the calculated F value for comparing the standard deviations? Are the standard deviations for the two locations significantly different at the 95% confidence level? ample Location 1 (% C) Location 2 (% C) 1 10.40 10.10 2 10.30 10.90 3 10.30 10.20 4 10.40 10.70 5 10.30 10.30
A standard reference material is certified to contain 94.6 ppm of an organic contaminant. Your analysis gives you the follow values, 98.6, 98.4, 95.1 and 97.2 ppm. Can you say with 95% confidence that your values differ from the certified value. Please show work