Materials For Civil And Construction Engineers In Si Units
4th Edition
ISBN: 9781292154404
Author: Michael S Mamlouk
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 1, Problem 1.40QP
A 4-m-long steel plate with a rectangular cross section (10 mm × 50 mm) is resting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be at 5°C. The steel has a modulus of elasticity equal to 200,000 MPa and a coefficient of thermal expansion equal to 1.1 × 10–5 m/m/°C.
a. What is the length of shrinkage?
b. What tension load is needed to return the length to the original value of 4 meters?
c. What is the longitudinal strain under tills load?
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A rectangular block of aluminum 30 mm * 60 mm * 90 mm is placed in a pressure chamber and subjected to a pressure of 100 MPa. If the modulus of elasticity is 70 GPa and Poisson’s ratio is 0.333, what will be the decrease in the longest side of the block, assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the block?
Determine the bulk modulus of elasticity (in N/m2) of a liquid that decreases in volume by 3% due to an increase in pressure from 1,000 N/cm2 to 21,000 N/cm2
A plastic cube with a 100mm * 100mm * 100mm is placed in a pressure chamber and subjected to a pressure of 100MPa. If the modulus of elasticity is 7GPa and Poisson’s ratio is 0.39, what will be the decrease in each side of the block, assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the cube?
Chapter 1 Solutions
Materials For Civil And Construction Engineers In Si Units
Ch. 1 - State three examples of a static load application...Ch. 1 - A material has the stressstrain behavior shown in...Ch. 1 - A tensile load of 50.000 lb is applied to a metal...Ch. 1 - A tensile load of 190 kN is applied to a round...Ch. 1 - A cylinder with a 6.0 in. diameter and 12.0 in....Ch. 1 - A metal rod with 0.5 inch diameter is subjected to...Ch. 1 - A rectangular block of aluminum 30 mm 60 mm 90...Ch. 1 - A plastic cube with a 4 in. 4 in. 4 in. is...Ch. 1 - A material has a stressstrain relationship that...Ch. 1 - On a graph, show the stressstrain relationship...
Ch. 1 - The rectangular block shown in Figure P1.11 is...Ch. 1 - The rectangular metal block shown in Figure P1.11...Ch. 1 - A cylindrical rod with a length of 380 mm and a...Ch. 1 - A cylindrical rod with a radius of 0.3 in. and a...Ch. 1 - A cylindrical rod with a diameter of 15.24 mm and...Ch. 1 - The stressstrain relationship shown in Figure...Ch. 1 - A tension test performed on a metal specimen to...Ch. 1 - An alloy has a yield strength of 41 ksi, a tensile...Ch. 1 - Prob. 1.21QPCh. 1 - Figure P1.22 shows (i) elasticperfectly plastic...Ch. 1 - An elastoplastic material with strain hardening...Ch. 1 - A brace alloy rod having a cross sectional area of...Ch. 1 - A brass alloy rod having a cross sectional area of...Ch. 1 - A copper rod with a diameter of 19 mm, modulus of...Ch. 1 - A copper rod with a diameter of 0.5 in., modulus...Ch. 1 - Define the following material behavior and provide...Ch. 1 - An asphalt concrete cylindrical specimen with a...Ch. 1 - What are the differences between modulus of...Ch. 1 - Prob. 1.33QPCh. 1 - A metal rod having a diameter of 10 mm is...Ch. 1 - What is the factor of safety? On what basis is its...Ch. 1 - Prob. 1.36QPCh. 1 - Prob. 1.37QPCh. 1 - A steel rod, which is free to move, has a length...Ch. 1 - In Problem 1.38, if the rod is snugly fitted...Ch. 1 - A 4-m-long steel plate with a rectangular cross...Ch. 1 - Estimate the tensile strength required to prevent...Ch. 1 - Prob. 1.42QPCh. 1 - Briefly discuss the variability of construction...Ch. 1 - In order to evaluate the properties of a material,...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - A contractor claims that the mean compressive...Ch. 1 - Prob. 1.47QPCh. 1 - Prob. 1.48QPCh. 1 - Prob. 1.49QPCh. 1 - Briefly discuss the concept behind each of the...Ch. 1 - Referring to the dial gauge shown in Figure P1.51,...Ch. 1 - Repeat Problem 1.51 using the dial gauge shown in...Ch. 1 - Measurements should be reported to the nearest...Ch. 1 - During calibration of an LVDT, the data shown in...Ch. 1 - During calibration of an LVDT, the data shown in...
Additional Engineering Textbook Solutions
Find more solutions based on key concepts
What production method for steel shapes is specified by the following organizations? AISI (American Iron and St...
Structural Steel Design (6th Edition)
5.11 What error results on a 200-ft sight with a level if the rod reading is 6.307 ft but the top of the
7-ft r...
Elementary Surveying: An Introduction To Geomatics (15th Edition)
11-1. Determine the moments at A,B, and C, then draw
the moment diagram for the beam. The moment of ine...
Structural Analysis (10th Edition)
A 3 ft square footing carries a sustained load of 10 k. It is placed on the surface of a 30 ft thick saturated ...
Foundation Design: Principles and Practices (3rd Edition)
1.2 Explain the difference between geodetic and plane
surveys,
Elementary Surveying (14th Edition)
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.Similar questions
- A plastic cube with a 100 mm * 100 mm * 100 mm. is placed in a pressurechamber and subjected to a pressure of 100 MPa. If the modulus of elasticityis 7 GPa and Poisson’s ratio is 0.39, what will be the decrease in each side ofthe block, assuming that the material remains within the linear elastic region?What will be the decrease in the volume of the cube?arrow_forwardA 4-m-long steel plate with a rectangular cross section (10 mm X 50 mm) isresting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be at 5°C. The steel has a modulus of elasticity equal to 200 GPa and a coefficient of thermal expansion equal to 1.1 X10-5m/m/°C. a. What is the length of shrinkage?b. What tension load is needed to return the length to the original value of 4 meters?c. What is the longitudinal strain under this load?arrow_forwardA 4-m-long steel plate with a rectangular cross section (10 mm * 50 mm) is resting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be at 5°C. The steel has a modulus of elasticity equal to 200,000 MPa and a coefficient of thermal expansion equal to 1.1 * 10-5m/m/°C.a. What is the length of shrinkage?b. What tension load is needed to return the length to the original value of 4 meters?c. What is the longitudinal strain under this load?arrow_forward
- A steel tape is 100 m long at a temperature of 20°C and a pull of 10 kg. It was used to measure a distance of 624.95 m at a temperature of 32°C with an applied pull of 15 kg during measurement with the tape supported at both ends. Coefficient of thermal expansion is 0.0000116/°C and a modulus of elasticity of 2x106kg/cm2. Weight of tape is 0.04 kg/m and a cross sectional area of 0.06 cm2. a) Compute the sag correction. b) Compute the total correction for tension, sag and temperature.c) Compute the corrected length of the line by applying the combined corrections for tension, sag and temperaturearrow_forwardA 4-meter-long steel plate with a rectangular cross section (10×50) mm is resting on a frictionless surface under the sun. The plate temperature is measured to be at 40°C. The plate is then moved into a cold room and is left to rest on a frictionless surface. After several hours, the plate temperature is measured to be at 5°C. The steel has a modulus of elasticity equal to 200,000 MPa and a coefficient of thermal expansion equal to 1.1×10-5m/m/°C. a. What is the length of shrinkage? b. What tension load is needed to return the length to the original value of 4 meters?arrow_forwardA cube made of an alloy with dimensions of 50 mm * 50 mm * 50 mm is placed into a pressure chamber and subjected to a pressure of 90 MPa. If the modulus of elasticity of the alloy is 100 GPa and Poisson’s ratio is 0.28, what will be the length of each side of the cube, assuming that the material remains within the elastic region?arrow_forward
- Find the change in volume of 1 cu.m. of water when subjected to a pressure increase of 14 MPa when the bulk modulus of elasticity of water is 2,200 MPa.arrow_forwardFind the change in volume of 10.00000 ft^3 of water at 80 deg.F. when subjected to a pressure increase of 500 psi. Water's bulk modulus of elasticity at this temperature is approximately 325,000 psi.arrow_forward1. If K = 2.2 GPa is the bulk modulus of elasticity for water, what pressure is required to reduce a volume by 0.6 percent? 2. A liquid is compressed. The change in pressure is 1000 psi. The change in density is 0.02%. What is the bulk modulus in psi? 3. The temperature of liquid water decreases from 80°C to 20°C. The percent change in absolute viscosity is ?arrow_forward
- A plastic cube with a 4 in. * 4 in. * 4 in. is placed in a pressure chamber and subjected to a pressure of 15,000 psi. If the modulus of elasticity is 1000 ksi and Poisson’s ratio is 0.49, what will be the decrease in each side of the block,assuming that the material remains within the linear elastic region? What will be the decrease in the volume of the cube?arrow_forward1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.arrow_forwardThe band in the figure below is stainless steel (coefficient of linear expansion = 17.3 ✕ 10−6°C−1; Young's modulus = 18 ✕ 1010 N/m2). It is essentially circular with an initial mean radius of 5.4 mm, a height of 4.4 mm, and a thickness of 0.51 mm. If the band just fits snugly over the tooth when heated to a temperature of 81°C, what is the tension in the band when it cools to a temperature of 37°C?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Engineering Fundamentals: An Introduction to Engi...Civil EngineeringISBN:9781305084766Author:Saeed MoaveniPublisher:Cengage Learning
Engineering Fundamentals: An Introduction to Engi...
Civil Engineering
ISBN:9781305084766
Author:Saeed Moaveni
Publisher:Cengage Learning
Material Properties 101; Author: Real Engineering;https://www.youtube.com/watch?v=BHZALtqAjeM;License: Standard YouTube License, CC-BY