Concept explainers
(a)
Calculate the maximum and minimum principal stresses.
(a)
Answer to Problem 10.1P
The maximum principal stress
The minimum principal stress
Explanation of Solution
Given information:
The normal stress along x axis
The normal stress along y axis
The shear stress along xy axis
Calculation:
Find the horizontal angle as follows:
Calculate the maximum principal stress
Substitute
Hence, the maximum principal stress
Calculate the minimum principal stress
Substitute
Hence, the minimum principal stress
(b)
Calculate the normal and shear stresses on plane AB.
(b)
Answer to Problem 10.1P
The normal stress on plane AB
The shear stress on plane AB
Explanation of Solution
Given information:
The normal stress along x axis
The normal stress along y axis
The shear stress along xy axis
The angle
Calculation:
Calculate the normal stress
Substitute
Hence, the normal stress on plane AB
Calculate the shear stress
Substitute
Therefore, the shear stress on plane AB
Want to see more full solutions like this?
Chapter 10 Solutions
MINDTAP ENGINEERING FOR DAS/SOBHAN'S PR
- A soil profile consists of a clay layer underlain by a sand layer, as shown in Figure. If a tube is inserted into the bottom sand layer and the water level rises to 1 m above the ground surface, determine the vertical effective stresses and porewater pressures at A, B, and C. What is the value of the porewater pressure at A to cause the vertical effective stress there to be zero?arrow_forwardThe soil stress state is shown in the figure, σx = 10 kN/m2, σy = 50 kN/m2, τxy = -10 kN/m2:(1) Please use Mohr circle to draw the soil stress state(2) Calculate the maximum principal stress σ1 and the minimum principal stress σ3(3) Please find the (pole) position(4) What is the angle of intersection between the maximum principal stress surface and the horizontal plane?arrow_forwardConsider the upward flow of water through a layer of sand in a tank as shown in Figure QI(c), For the sand, the following are given: void ratio (e) = 0.52 and specific gravity of solid = 2.67. Determine: (i) Total stress, pore water pressure and effective stress at points A and B (ii) The upward seepage force per unit volume of soil.arrow_forward
- Q#3. An earth embankment diagram is shown in Figure.1. Determine the vertical stress increase at A due to embankment load.arrow_forwardAn earth embankment is shown in Figure 10.44. Determine the stress increase at point A due to the embankment load. Given: β = 25°, γ = 119 lb/ft 3, x = 55 ft, y = 28 ft, and z = 20 ft.arrow_forwardRefer to Figure 10.46. A flexible circular area of radius 6 m is uniformly loaded. Given: q = 565 kN/m2. Using Newmarks chart, determine the increase in vertical stress, z, at point A. Figure 10.46arrow_forward
- Refer to Figure 8.24. Determine the vertical stress increase, , at point A with the following values: q1 = 100 kN/m x1 = 3 m z = 2 m q2 = 200 kN/m x2 = 2 m FIG. 8.24 Stress at a point due to two line loadsarrow_forwardFor the same line loads given in Problem 10.8, determine the vertical stress increase, z, at a point located 4 m below the line load, q2. Refer to Figure 10.41. Determine the vertical stress increase, z, at point A with the following values: q1 = 110 kN/m, q2 = 440 kN/m, x1 = 6 m, x2 = 3 m, and z = 4 m. Figure 10.41arrow_forwardRefer to Figure 8.13. The magnitude of the line load q is 45 kN/m. Calculate and plot the variation of the vertical stress increase, between the limits of x = 10 m and x = +10 m, given z = 4 m. FIG. 8.13 Line load over the surface of a semiinfinite soil massarrow_forward
- Use Eq. (6.14) to determine the stress increase () at z = 10 ft below the center of the area described in Problem 6.5. 6.5 Refer to Figure 6.6, which shows a flexible rectangular area. Given: B1 = 4 ft, B2 = 6 ft, L1, = 8 ft, and L2 = 10 ft. If the area is subjected to a uniform load of 3000 lb/ft2, determine the stress increase at a depth of 10 ft located immediately below point O. Figure 6.6 Stress below any point of a loaded flexible rectangular areaarrow_forwardRefer to the flexible loaded rectangular area shown in Figure 10.47. Using Eq. (10.36), determine the vertical stress increase below the center of the loaded area at depths z = 3, 6, 9, 12, and 15 m. Figure 10.47arrow_forwardRepeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43arrow_forward
- Principles of Geotechnical Engineering (MindTap C...Civil EngineeringISBN:9781305970939Author:Braja M. Das, Khaled SobhanPublisher:Cengage LearningFundamentals of Geotechnical Engineering (MindTap...Civil EngineeringISBN:9781305635180Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage LearningPrinciples of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781305081550Author:Braja M. DasPublisher:Cengage Learning
- Principles of Foundation Engineering (MindTap Cou...Civil EngineeringISBN:9781337705028Author:Braja M. Das, Nagaratnam SivakuganPublisher:Cengage Learning