SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
10th Edition
ISBN: 9781260028379
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 27P
A compression spring is needed to fit within a 1-in diameter hole. To allow for some clearance, the outside diameter of the spring is to be no larger than 0.9 in. To ensure a reasonable coil, use a spring index of 8. The spring is to be used in a machine by compressing it from a free length of 3 in to a solid length of 1 in. The spring should have squared ends, and is unpeened, and is to be made from music wire.
- (a) Determine a suitable wire diameter.
- (b) Determine a suitable total number of coils.
- (c) Determine the spring constant.
- (d) Determine the static factor of safety when compressed to solid length.
- (e) Determine the fatigue factor of safety when repeatedly cycled from free length to solid length. Use the Gerber-Zimmerli fatigue-failure criterion.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
Determine the wahl's factor of a spring designed to fire a 3kg projectile. The outside diameter of the cil is 170 mm with 10mm wire diameter and a total of 20 coils squared and ground. The spring has a free length of 625 mm. When set or loaded the spring is compressed to a length of 444mm.
Chapter 10 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
Ch. 10 - Within the range of recommended values of the...Ch. 10 - It is instructive to examine the question of the...Ch. 10 - A helical compression spring is wound using...Ch. 10 - The spring in Prob. 10-3 is to be used with a...Ch. 10 - A helical compression spring is made with...Ch. 10 - A helical compression spring is to be made of...Ch. 10 - A helical compression spring is made of hard-drawn...Ch. 10 - The spring of Prob. 107 is to be used with a...Ch. 10 - 109 to 1019 Listed in the tables are six springs...Ch. 10 - 109 to 1019 Listed in the tables are six springs...
Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 12PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 17PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Consider the steel spring in the illustration. (a)...Ch. 10 - A static service music wire helical compression...Ch. 10 - Solve Prob. 1021 by iterating with an initial...Ch. 10 - A holding fixture for a workpiece 37.5 mm thick at...Ch. 10 - Solve Prob. 10-23 by iterating with an initial...Ch. 10 - A compression spring is needed to fit over a...Ch. 10 - A compression spring is needed to fit within a...Ch. 10 - A helical compression spring is to be cycled...Ch. 10 - The figure shows a conical compression helical...Ch. 10 - A helical coil compression spring is needed for...Ch. 10 - Solve Prob. 10-30 using the Goodman-Zimmerli...Ch. 10 - Solve Prob. 10-30 using the Sines-Zimmerli...Ch. 10 - Design the spring of Ex. 10-5 using the...Ch. 10 - Solve Prob. 10-33 using the Goodman-Zimmerli...Ch. 10 - A hard-drawn spring steel extension spring is to...Ch. 10 - The extension spring shown in the figure has...Ch. 10 - Design an infinite-life helical coil extension...Ch. 10 - Prove Eq. (10-40). Hint: Using Castigliunos...Ch. 10 - The figure shows a finger exerciser used by...Ch. 10 - The rat trap shown in the figure uses two...Ch. 10 - Prob. 41PCh. 10 - Prob. 42PCh. 10 - Figure 10-13b shows a spring of constant thickness...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).arrow_forwardA semi-elliptic spring used for automobile suspension, consists of twoextra full-length leaves and eight graduated-length leaves, including themaster leaf. The centre-to-centre distance between the two eyes is 1 m.The leaves are made of steel 55Si2Mo90 (S = 1500 N/mm yt2 andE = 207 000 N/mm2) and the factor of safety is 2. The maximum springload is 30 kN. The leaves are pre-stressed so as to equalize stresses in allleaves under maximum load. Determine the dimensions of thecross-section of the leaves and the deflection at the end of the spring.arrow_forwardA helical compression spring has a scale of 400 lbs/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load P of 750 lbs and for the average service Determine the standard size wire diameter Determine the number of active coils Determine the solid height Determine the stress at solid heightarrow_forward
- A semi-elliptic spring used for automobile suspension, consists of two extra full-length leaves and eight graduated-length leaves, including the master leaf. The centre-to centre distance between the two eyes is 1 m. The leaves are made of steel 55Si2Mo90 (Syt = 1500 N/mm2and E = 207000 N/mm2) and the factor of safety is 2. The maximum spring load is 30 kN. The leaves are pre- stressed so as to equalize stresses in all leaves under maximum load. Determine the dimensions of the cross-section of the leaves and the deflection at the end of the spring.arrow_forwardThe inner spring of a compound helical spring is arranged within and concentric with the outer one and is shorter by 9 mm. The outer spring has 10 coils with a mean diameter of 24 mm and a wire diameter of 3 mm. (a) Determine the stiffness of the inner spring when an axial load of 162 N causes the outer spring to compress by 16 mm. If the radial clearance between the springs is 1.5 mm and the inner spring has 8 coils, find its wire diameter. (c) Disregarding the effect of curvature, find the maximum shear stress in each of the spring. Given G = 78 GPa.arrow_forwardA helical spring is provided with a rigid plate at each end. A bolt passes through the spring and the end plates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and the plates are each 25 mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire (take E = 200 GPa and G = 80 GPa).arrow_forward
- A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .arrow_forwardA bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.arrow_forwardA typical compound helical spring consists of two coaxial closed coil spring having the following particulars: Outer spring 1: Mean coil diameter = 100mm Wire diameter = 12.5 mm No. of turns = 15 Inner spring 2: Mean coil diameter = 75 mm No. of turns = 20 Both the springs are of equal initial length when unloaded. If the working stress for each spring is to be the same. The modulus of rigidity for the wire material is 80 GPa. Calculate the following: a. Diameter of steel wire for inner spring b. Stiffness of inner spring c. Stiffness of the compound springarrow_forward
- a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and presetting is to be used. the operation load of the spring can be considered static. If the maximum working force is 292 N and a force of 35 N is required when the spring is 30 mm longer, determine the spring constant karrow_forward(2) A coil spring is to be used for the front suspension of a car. The spring is to have a rate of 400lb/in, an inside diameter of 4.0-in, & a free length of 14⅛-in, with squared & ground ends. The material is to be oil-tempered chrome-vanadium steel. Recommend the rod diameter & the number of coils for a design load of 1,500lb.arrow_forwardAn engine valve spring must exert a force of 300 N when the valve is closed and 500 N when the valve is open as shown in Figure 3. The maximum lift of spring is 8 mm (ymax). With a safety factor of 1.6 a. Design the wire diameter. b. Calculate the number of active coils. c. Calculate the number of total coils and the free length. d. Check the stability. Design Decisions: The spring is made of ASTM, A227, unpeened, clash allowance of 0.15, G = 79 GPa, squared and ground ends and C = 6.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
International Edition---engineering Mechanics: St...Mechanical EngineeringISBN:9781305501607Author:Andrew Pytel And Jaan KiusalaasPublisher:CENGAGE L
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License