SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
10th Edition
ISBN: 9781260028379
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Question
Chapter 10, Problem 42P
(a)
To determine
The spring rate by using Castigliano’s theorem.
(b)
To determine
The spring rate.
(c)
To determine
The load for which cause the wire to yield.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
A motor drives a shaft at 12 Hz and delivers 20 kW of power as shown in Fig.4. (a) If the shaft has a diameter of 30 mm, what is the maximum shear stress τmax in the shaft? (b) If the maximum allowable shear stress is 40 MPa, what is the minimum permissible diameter dmin of the shaft?
A solid circular bar of diameter d = 50 mm is twisted in a testing machine until the applied torque reaches the value T = 500 Nm as shown in Fig.4. At this value of torque, a strain gage oriented at 45 ° to the axis of the bar gives a reading ε =339 ×10-6 . What is the shear modulus G of the material?
A bar of titanium alloy of length 120mm and square cross – section, 7.5 mm x 7.5 mm, is pulled axially by a force of 15 kN. Find the percentage decrease in thickness if E = 106 GN/m2 and v = 0.33 m/s. V= velocity
A bar of aluminum alloy of rectangular section75 mm x 20 mm and 800 mm long is stretched by an axial force of 150 kN. Find the volumetric strain, the actual change in volume and the percentage reduction in cross – sectional area of the bar. Take E = 70 GN/m2 and v = 0.34 m/s.V=velocity
A spring (squared and ground) having a pitch 0.75 inch has a mean diameter of 1.5in and a wire diameter of 0.25in. After applying a certain load, the spring deflects 0.5in with a corresponding stress of 30.75 ksi. The spring is to be made of tempered steel wire having a shear modulus of 12 million psi.
Chapter 10 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
Ch. 10 - Within the range of recommended values of the...Ch. 10 - It is instructive to examine the question of the...Ch. 10 - A helical compression spring is wound using...Ch. 10 - The spring in Prob. 10-3 is to be used with a...Ch. 10 - A helical compression spring is made with...Ch. 10 - A helical compression spring is to be made of...Ch. 10 - A helical compression spring is made of hard-drawn...Ch. 10 - The spring of Prob. 107 is to be used with a...Ch. 10 - 109 to 1019 Listed in the tables are six springs...Ch. 10 - 109 to 1019 Listed in the tables are six springs...
Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 12PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 17PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Consider the steel spring in the illustration. (a)...Ch. 10 - A static service music wire helical compression...Ch. 10 - Solve Prob. 1021 by iterating with an initial...Ch. 10 - A holding fixture for a workpiece 37.5 mm thick at...Ch. 10 - Solve Prob. 10-23 by iterating with an initial...Ch. 10 - A compression spring is needed to fit over a...Ch. 10 - A compression spring is needed to fit within a...Ch. 10 - A helical compression spring is to be cycled...Ch. 10 - The figure shows a conical compression helical...Ch. 10 - A helical coil compression spring is needed for...Ch. 10 - Solve Prob. 10-30 using the Goodman-Zimmerli...Ch. 10 - Solve Prob. 10-30 using the Sines-Zimmerli...Ch. 10 - Design the spring of Ex. 10-5 using the...Ch. 10 - Solve Prob. 10-33 using the Goodman-Zimmerli...Ch. 10 - A hard-drawn spring steel extension spring is to...Ch. 10 - The extension spring shown in the figure has...Ch. 10 - Design an infinite-life helical coil extension...Ch. 10 - Prove Eq. (10-40). Hint: Using Castigliunos...Ch. 10 - The figure shows a finger exerciser used by...Ch. 10 - The rat trap shown in the figure uses two...Ch. 10 - Prob. 41PCh. 10 - Prob. 42PCh. 10 - Figure 10-13b shows a spring of constant thickness...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A Hollow power transmission shaft of length ‘L’ 1103 mm, outer diameter ‘D’ 73mm and inner diameter 'd' 50. is required to transmit a power of P 60kW at a speed of 2950rpm. The modulus of rigidity of hardened carbon steel, which the shaft is made of, is 79.5 GPa Calculate the angle of twist of the above stating your answer in degrees?arrow_forwardThe disc clutch of an automobile is carried on a 2-inch 6-splined shaft and not to slide under load. The nominal dimensions are as follows: b = 0.25 D; t = 0.075 D and d = 0.85 D. The hub length of 150 % of shaft diameter. Determine the total horsepower transmitted at 3,600 rpm, if the yield strength of the shaft is 1,400 psiarrow_forwardThe bar shown, made from ground steel (Sy = 36 ksi, Sut = 57 ksi), is subjected to a fully reversed bending moment of 30 lb.ft. Calculate the corrected endurance limit for a 90% reliability. The bar will be used at a temperature of 550 oC. Select one: a. Se = 11.83 ksi b. Se = 10.20 ksi c. Se = 13.44 ksi d. Se = 8.55 ksiarrow_forward
- The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:arrow_forwardFind the equivalent stresses at Points 1 and 2 of the element with given geometry and loading conditions according to the Maximum shear stress hypothesis and the Maximum strain energy hypothesis. Shaft diameter: 20 mm, Shaft Length 120 mm, F1 = 750N, F2 = 3000N, Mb = 2400 N.mm. Steel if St37 and Safety coefficient is 2 If taken, will this stick work safely under these operating conditions? (Yield of given steel Strength 225 Mpa, Tensile strength 370 Mpa)arrow_forwardPart A For a hard aluminum notched part having notch dimension r = 0.75 in, geometric stress-concentration factor Kt = 2.8, material strength Sut = 50 kpsi, and bending loading type, find the Neuber factor, a (in inches). Part B Find the material's notch sensitivity, q. Part C Find the fatigue stress-concentration factor. Kf.arrow_forward
- A circular shaft of diameter D, groove diameter d, and groove radius r is subjected to a fully reversed torque T = 1000 lb-in and a fully reversed moment M = 500 lb-in. Find the factor of safety of the shaft for infinite lifetime using the modified Goodman diagram, if the shaft is made from steel (Sut = 85 ksi, Se = 45 ksi). Given: D = 2 in, d = 1 in, r = 0.5 in. Assume all fatigue stress concentration factors are equal to 1arrow_forward4 helical springs is used in a suspension system of a motorcycle. The mean coil diameter is 15 cm, spring constant is 40,000 N/m, shear modulus = 80x10^9 N/(m^2), and has 8 effective turns. Determine what must be the wire diameter of the helical spring.arrow_forwardThe figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and ultimate tensile strength of 700 MPa. Diameters of the shaft are D=30 mm and d=20 mm. Fillet radius of the shoulder section is 2.5 mm. The shaft is rotating and subjected to steady bending moment of M=51 Nm, steady torsion of T=58 Nm and steady axial load of F=14 kN. The operating temperature of the shaft is 20 ᵒC and reliability is 99%. The shaft has ground surface.Calculate the mean component of the shear stress (in MPa)arrow_forward
- The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and ultimate tensile strength of 700 MPa. Diameters of the shaft are D=30 mm and d=20 mm. Fillet radius of the shoulder section is 2.5 mm. The shaft is rotating and subjected to steady bending moment of M=51 Nm, steady torsion of T=58 Nm and steady axial load of F=14 kN. The operating temperature of the shaft is 20 ᵒC and reliability is 99%. The shaft has ground surface. Calculate the alternating component of the normal stress (in MPa). (If there is no alternating component of the normal stress, enter "0" in the answer box)arrow_forwardA spur gear wheel will be produced for the motion mechanism of a woodworking machine driven by a single cylinder engine. Considering the data below, find the tangential force on the gear in Newtons according to the root strength. Module for gear=5 cm ; module width ratio =14 ; number of teeth=16 ; Clutch ratio=1 ; form factor Kf=1.4 ; load distribution factor Km=1.5 ; the circumferential speed of the gear is =56 m/sec (To be used only in Kv calculation). Safety stress of gear material=37 N/mm2. 1-) Table will NOT be used for Kv-Speed factor. It will be calculated with the formula Kv=1+0.03*V. 2-) V in Kv calculation shows the velocity as m/sec. 3-) It will be taken as Pi=3.14.arrow_forwardRead and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Everything About COMBINED LOADING in 10 Minutes! Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=N-PlI900hSg;License: Standard youtube license