SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
10th Edition
ISBN: 9781260028379
Author: BUDYNAS
Publisher: MCG/CREATE
expand_more
expand_more
format_list_bulleted
Videos
Textbook Question
Chapter 10, Problem 36P
The extension spring shown in the figure has full-twisted loop ends. The material is AISI 1065 OQ&T wire. The spring has 84 coils and is close-wound with a preload of 16 lbf.
- (a) Find the closed length of the spring.
- (b) Find the torsional stress in the spring corresponding to the preload.
- (c) Estimate the spring rate.
- (d) What load would cause permanent deformation?
- (e) What is the spring deflection corresponding to the load found in part d?
Problem 10-36
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Chapter 10 Solutions
SHIGLEY'S MECH.ENGR...(LL)-PKG.>CUSTOM<
Ch. 10 - Within the range of recommended values of the...Ch. 10 - It is instructive to examine the question of the...Ch. 10 - A helical compression spring is wound using...Ch. 10 - The spring in Prob. 10-3 is to be used with a...Ch. 10 - A helical compression spring is made with...Ch. 10 - A helical compression spring is to be made of...Ch. 10 - A helical compression spring is made of hard-drawn...Ch. 10 - The spring of Prob. 107 is to be used with a...Ch. 10 - 109 to 1019 Listed in the tables are six springs...Ch. 10 - 109 to 1019 Listed in the tables are six springs...
Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 12PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Prob. 17PCh. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - 10-9 to 10-19 Listed in the tables are six springs...Ch. 10 - Consider the steel spring in the illustration. (a)...Ch. 10 - A static service music wire helical compression...Ch. 10 - Solve Prob. 1021 by iterating with an initial...Ch. 10 - A holding fixture for a workpiece 37.5 mm thick at...Ch. 10 - Solve Prob. 10-23 by iterating with an initial...Ch. 10 - A compression spring is needed to fit over a...Ch. 10 - A compression spring is needed to fit within a...Ch. 10 - A helical compression spring is to be cycled...Ch. 10 - The figure shows a conical compression helical...Ch. 10 - A helical coil compression spring is needed for...Ch. 10 - Solve Prob. 10-30 using the Goodman-Zimmerli...Ch. 10 - Solve Prob. 10-30 using the Sines-Zimmerli...Ch. 10 - Design the spring of Ex. 10-5 using the...Ch. 10 - Solve Prob. 10-33 using the Goodman-Zimmerli...Ch. 10 - A hard-drawn spring steel extension spring is to...Ch. 10 - The extension spring shown in the figure has...Ch. 10 - Design an infinite-life helical coil extension...Ch. 10 - Prove Eq. (10-40). Hint: Using Castigliunos...Ch. 10 - The figure shows a finger exerciser used by...Ch. 10 - The rat trap shown in the figure uses two...Ch. 10 - Prob. 41PCh. 10 - Prob. 42PCh. 10 - Figure 10-13b shows a spring of constant thickness...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?arrow_forwardRepeat Problem 2.3-18, but assume that the bar is made of copper alloy. Calculate the displacements SBand Scif P = 50 kips, L = 5 ft = 3/5 in., b1= 2.75 in., b2= 3 in., and E = 16,000 ksi.arrow_forwardA tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?arrow_forward
- A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10 in.) and a vertical arm BC (length c = 7 in.) pivoted al point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer al C is controlled by a spring, Jt = 5 lb/in., that is attached to a threaded rod. The pitch of the threads is p = 1/16 in. Under application of load W, 12 revolutions of the nut are required to bring the pointer back to the mark. Calculate the weight W.arrow_forwardA bumper for a mine car is constructed with a spring of stiffness k = 1120 lb/in. (see figure). If a car weighing 3450 lb is traveling at velocity v = 7 mph when it strikes the spring, what is the maximum shortening of the spring?arrow_forwardA cable and pulley system at D is used to bring a 230-lcg pole (ACB) to a vertical position, as shown in the Figure part a. The cable has tensile force T and is attached at C. The length L of the pole is 6.0m, the outer diameter is d = 140 mm. and the wall thickness is t = 12 mm. The pole pivots about a pin at A in figure part b. The allowable shear stress in the pin is 60 MPa and the allowable bearing stress is 90 MPa. Find the minimum diameter of the pin at A in order to support the weight of the pole in the position shown in the figure part a.arrow_forward
- A hollow circular tube A fits over the end of a solid circular bar B, as shown in the figure. The far ends of both bars are fixed. Initially, a hole through bar B makes an angle ß with a line through two holes in tube A. Then bar B is twisted until the holes are aligned, and a pin is placed through the holes. When bar B is released and the system returns to equilibrium, what is the total strain energy U of the two bars? (Let lAand lBrepresent the polar moments of inertia of bars A and B, respectively. The length L and shear modulus of elasticity G are the same for both bars.)arrow_forwardA magnesium-alloy wire of diameter d = 4mm and length L rotates inside a flexible tube in order to open or close a switch from a remote location (see figure). A torque Tis applied manually (either clockwise or counterclockwise) at end 5, thus twisting the wire inside the tube. At the other end A, the rotation of the wire operates a handle that opens or closes the switch. A torque T0 = 0.2 N · m is required to operate the switch. The torsional stiffness of the tube, combined with friction between the tube and the wire, induces a distributed torque of constant intensity t = 0.04N m/m (torque per unit distance) acting along the entire length of the wire. (a) If the allowable shear stress in the wire is T allow = 30 MPa, what is the longest permissible length Lmaxof the wire?arrow_forwardA crank arm consists of a solid segment of length bxand diameter rf, a segment of length bltand a segment of length byas shown in the figure. Two loads P act as shown: one parallel to — vand another parallel to —y. Each load P equals 1.2 kN. The crankshaft dimensions are A] = 75 mm, fr> = 125 mm, and b3= 35 mm. The diameter of the upper shaft isd = 22 mm, (a) Determine the maximum tensile, compressive, and shear stresses at point A, which is located on the surface of the shaft at the z axis. (b) Determine the maximum tensile, compressive, and shear stresses at point B, which is located on the surface of the shaft at the y axisarrow_forward
- Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.arrow_forwardA polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the springarrow_forwardTwo sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Mechanical SPRING DESIGN Strategy and Restrictions in Under 15 Minutes!; Author: Less Boring Lectures;https://www.youtube.com/watch?v=dsWQrzfQt3s;License: Standard Youtube License