COLLEGE PHYS. VOL 1 LLF W/MODMAST >IC<
10th Edition
ISBN: 9781323149454
Author: YOUNG
Publisher: PEARSON C
expand_more
expand_more
format_list_bulleted
Concept explainers
Question
Chapter 10, Problem 55GP
(a)
To determine
The tension in the cable.
(b)
To determine
The magnitude and direction of the force the hinge exerts on the bridge.
(c)
To determine
The initial
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A sign is supported by a uniform horizontal boom of length 3.10 m and weight 72.0 N. A cable, inclined at an angle of 16 °with the boom, is attached at a distance of 2.71 m from the hinge at the wall. The weight of the sign is 108.0 N. What is the tension in the cable and what are the horizontal and vertical forces Fx and Fy exerted on the boom by the hinge? Comment on the magnitude of Fy.
T= In N
Fx= in N
Fy= in N
The magnitude of Fy is select (small or large) compared to that of Fx and T.
A uniform drawbridge must be held at a 38o angle above the horizontal to allow ships to pass underneath. The drawbridge weights 55000 N and is 15.0 m long. A cable is connected 3.5 m from the hinge where the bridge pivots (measured along the bridge) and pulls horizontally on the bridge to hold it in place.
What is the tension in the cable?
Find the magnitude and direction of the force the hinge exerts on the bridge.
If the cable suddenly breaks, what is the magnitude of the angular acceleration of the drawbridge just after the cable breaks?
What is the angular speed of the drawbridge as it becomes horizontal?
What is the velocity of the drawbridge, just before it “hits” (i.e. goes horizontal)?
Two painters are carrying a uniform horizontal ladder that is 12 feet long and weighs 200 N. If one person applies an upward force equal to 85 N at one end, at what point does the other person lift?
Chapter 10 Solutions
COLLEGE PHYS. VOL 1 LLF W/MODMAST >IC<
Ch. 10 - When tightening a bolt, mechanics sometimes extend...Ch. 10 - Prob. 2CQCh. 10 - Two identical uniform 30 cm bricks are placed one...Ch. 10 - (a) If the forces on an object balance, do the...Ch. 10 - (a) Can you change the location of your bodys...Ch. 10 - Serious bicyclists say that if you reduce the...Ch. 10 - Prob. 7CQCh. 10 - In terms of torques, discuss the action of a claw...Ch. 10 - Why is a tapered water glass with a narrow base...Ch. 10 - True or false? In picking an axis about which to...
Ch. 10 - Global warming. As the earths climate continues to...Ch. 10 - If two spinning objects have the same angular...Ch. 10 - You are designing a wheel that must have a fixed...Ch. 10 - Prob. 2MCPCh. 10 - A student is sitting on a frictionless rotating...Ch. 10 - If the torques on an object balance, then it...Ch. 10 - If the forces on an object balance, then it...Ch. 10 - Prob. 6MCPCh. 10 - A person pushes vertically downward with force P...Ch. 10 - String is wrapped around the outer rim of a solid...Ch. 10 - A ball of mass 0.20 kg is whirled in a horizontal...Ch. 10 - A heavy solid disk rotating freely and slowed only...Ch. 10 - A uniform metal meterstick is balanced as shown in...Ch. 10 - Prob. 1PCh. 10 - Calculate the net torque about point O for the two...Ch. 10 - Three forces are applied to a wheel of radius...Ch. 10 - A 4 N and a 10 N force act on an object. The...Ch. 10 - A square metal plate 0.180 m on each side is...Ch. 10 - A cord is wrapped around the rim of a wheel 0.250...Ch. 10 - A certain type of propeller blade can be modeled...Ch. 10 - A 750 g grinding wheel 25.0 cm in diameter is in...Ch. 10 - A grindstone in the shape of a solid disk with...Ch. 10 - A solid, uniform cylinder with mass 8.00 kg and...Ch. 10 - A 2.00 kg stone is tied to a thin, light wire...Ch. 10 - A light rope is wrapped several times around a...Ch. 10 - A thin, light string is wrapped around the rim of...Ch. 10 - 14. A uniform, 8.40-kg, spherical shell 50.0 cm in...Ch. 10 - A hollow spherical shell with mass 2.00 kg rolls...Ch. 10 - A solid disk of radius 8.50 cm and mass 1.25 kg,...Ch. 10 - What is the power output in horsepower of an...Ch. 10 - A solid uniform sphere of mass 5 kg and radius 0.1...Ch. 10 - A playground merry-go-round has a radius of 4.40 m...Ch. 10 - The flywheel of a motor has a mass of 300.0 kg and...Ch. 10 - Calculate the angular momentum and kinetic energy...Ch. 10 - (a) Calculate the magnitude of the angular...Ch. 10 - A small 0.300 kg bird is flying horizontally at...Ch. 10 - A. small 4.0 kg brick is released from rest 2.5 m...Ch. 10 - The London Eye is the tallest Ferris wheel in...Ch. 10 - A certain drawbridge can be modeled as a uniform...Ch. 10 - On an old-fashioned rotating piano stool, a woman...Ch. 10 - The spinning figure skater. The outstretched hands...Ch. 10 - A small block on a frictionless horizontal surface...Ch. 10 - A uniform 2 kg solid disk of radius R 0.4 m is...Ch. 10 - A diver comes off a board with arms straight up...Ch. 10 - A large turntable rotates about a fixed vertical...Ch. 10 - A large wooden turntable in the shape of a flat...Ch. 10 - Which of the objects shown in Figure 10.55 are in...Ch. 10 - (a) In each of the objects in Figure 10.56, what...Ch. 10 - Prob. 36PCh. 10 - Prob. 37PCh. 10 - Prob. 38PCh. 10 - Prob. 39PCh. 10 - Prob. 40PCh. 10 - The horizontal beam in Figure 10.60 weighs 150 N,...Ch. 10 - The boom in Figure 10.61 weighs 2600 N and is...Ch. 10 - A uniform ladder 7.0 m long weighing 450 N rests...Ch. 10 - A 9.0 m uniform beam is hinged to a vertical wall...Ch. 10 - A uniform beam 4.0 m long and weighing 2500 N...Ch. 10 - A diving board 3.00 m long is supported at a point...Ch. 10 - Two people carry a heavy electric motor by placing...Ch. 10 - Pumping iron. A 72.0 kg weightlifter is doing arm...Ch. 10 - The deltoid muscle. The deltoid muscle is the main...Ch. 10 - The rotor (flywheel) of a toy gyroscope has a mass...Ch. 10 - For each of the following rotating objects,...Ch. 10 - Prob. 52GPCh. 10 - A good workout. You are doing exercises on a...Ch. 10 - Prior to being placed in its hole, a 5700 N,...Ch. 10 - Prob. 55GPCh. 10 - One end of a 1.2-m-long beam is hinged to a...Ch. 10 - The farmyard gate. A gate 4.00 m wide and 2.00 m...Ch. 10 - 58. Atwoods machine. Figure 10.72 illustrates an...Ch. 10 - Prob. 59GPCh. 10 - The forces on the foot. A 750 N athlete standing...Ch. 10 - A uniform solid cylinder of mass M is supported on...Ch. 10 - Prob. 62GPCh. 10 - You are trying to raise a bicycle wheel of mass m...Ch. 10 - An experimental bicycle wheel is placed on a test...Ch. 10 - Prob. 65GPCh. 10 - Disks A and B are mounted on shaft SS and may be...Ch. 10 - One end of a thin, uniform rod is connected to a...Ch. 10 - A uniform, 7.5-m-long beam weighing 9000 N is...Ch. 10 - Human moment of inertia. The moment of inertia of...Ch. 10 - While the turntable is being accelerated, the...Ch. 10 - A doubling of the torque produces a greater...Ch. 10 - If the bodys center of mass were not placed on the...Ch. 10 - Torques and tug-of-war. In a study of the...Ch. 10 - If the competitor leans slightly farther back...Ch. 10 - Torques and tug-of-war. In a study of the...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.Similar questions
- A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.arrow_forwardAn aluminium (=2.7g/cm3) wire is suspended from the ceiling and hangs vertically. How long must the wire be before the stress at its upper end reaches the proportionality limit, which is 8.0107N/m2 ?arrow_forwardCheck Your Understanding A 400.0-N sign hangs from the end of a uniform strut. The strut is 4.0 m long and weighs 600.0 N. The strut is supported by a hinge at the wall and by a cable whose other end is tied to the wall at a point 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut.arrow_forward
- Two rods, one made of copper and the other of steel, have the same dimensions. If the copper rod stretches by 0.15mm under some stress, how much does the steel rod stretch under the same stress?arrow_forwardProblems 33 and 34 are paired. One end of a uniform beam that weighs 2.80 102 N is attached to a wall with a hinge pin. The other end is supported by a cable making the angles shown in Figure P14.33. Find the tension in the cable. FIGURE P14.33 Problems 33 and 34.arrow_forwardA uniform 40.0-kg scaffold of length 60 m is supported by tow light cables below. An 80.0 kg painter stands 1.0 m from the left end of the scaffold, and his painting equipment is 1.5 m from the right end. If the tension in the cable is twice that in the right cable, find the cables and mass of the equipment.arrow_forward
- Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?arrow_forwardIn order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?arrow_forwardA stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.arrow_forward
- Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.arrow_forwardOne end of a uniform rod of weight w = 73.5 N and length L = 2.55 m is supported by a cable at an angle of ? = 37.0°above the rod. The other end rests on a small frictionless support and presses into a wall as shown in the figure. Determine the magnitude n of the vertical normal force exerted by the support on the rod and find the magnitude T of the tension in the cable.arrow_forwardA 10 m ladder with a mass of 15 kg leans against the wall. If the ladder is in static equilibrium, what must be the normal force from the ground, assuming the wall is frictionless?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityPhysics for Scientists and Engineers: Foundations...PhysicsISBN:9781133939146Author:Katz, Debora M.Publisher:Cengage Learning
Principles of Physics: A Calculus-Based Text
Physics
ISBN:9781133104261
Author:Raymond A. Serway, John W. Jewett
Publisher:Cengage Learning
University Physics Volume 1
Physics
ISBN:9781938168277
Author:William Moebs, Samuel J. Ling, Jeff Sanny
Publisher:OpenStax - Rice University
Physics for Scientists and Engineers: Foundations...
Physics
ISBN:9781133939146
Author:Katz, Debora M.
Publisher:Cengage Learning