Concept explainers
Torques and tug-of-war. In a study of the biomechanics of the tug-of-war, a 2.0-m-tall, 80.0 kg competitor in the middle of the line is considered to be a rigid body leaning back at an angle of 30.0° to the vertical (Figure 10.81). The competitor is pulling on a rope that is held horizontal a distance of 1.5 m from his feet (as measured along the line of the body). At the moment shown in the figure, the man is stationary and the tension in the rope in front of him is T1 = 1160 N. Since there is friction between the rope and his hands, the tension in the rope behind him, T2, is not equal to T1. His center of mass is halfway between his feet and the top of his head. The coefficient of static friction between his feet and the ground is 0.65.
Figure 10.81
Problems 73–76
73. What is the tension T2 in the rope behind him?
- A. 590 N
- B. 650 N
- C. 860 N
- D. 1100 N
Want to see the full answer?
Check out a sample textbook solutionChapter 10 Solutions
COLLEGE PHYS. VOL 1 LLF W/MODMAST >IC<
Additional Science Textbook Solutions
Conceptual Integrated Science
Essential University Physics: Volume 1 (3rd Edition)
The Cosmic Perspective Fundamentals (2nd Edition)
College Physics
Essential University Physics (3rd Edition)
Physics: Principles with Applications
- Answer yes or no to the following questions. (a) Is it possible to calculate the torque acting on a rigid object without specifying an axis of rotation? (b) Is the torque independent of the location of the axis of rotation?arrow_forwardAssume a single 300-N force is exerted on a bicycle frame as shown in Figure OQ10.5. Consider the torque produced by this force about axes perpendicular to the plane of the paper and through each of the points A through E, where E is the center of mass of the frame. Rank the torques A, B, C, D, and E from largest to smallest, noting that zero is greater than a negative quantity. If two torques are equal, note their equality in your ranking. Figure OQ10.5arrow_forwardA stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.arrow_forward
- When tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting in newton-meters (relative to the center of the bolt)?arrow_forwardWhat three factors affect the torque created by a force relative to a specific pivot point?arrow_forwardA meter stick is pivoted at its 50cm mark but does not balance because of non-uniformities in its material that cause its center of gravity to be displaced from its geometrical center. However, when weights of 150g and 300g are placed at the 10cm and 75cm marks, respectively, balance is obtained. The weights are then interchanged, and balance is again obtained by shifting the pivot point to the 43cm mark. Find the mass of the meter stick and the location of its center of gravity.arrow_forward
- What is the minimum magnitude of torque that can be exerted on a rigid body by a 100.0 N force applied at a point that is 0.1 m from the axis of rotation?arrow_forwardTweedledum and Tweedledee are carrying a uniform wooden board that is LLL = 3.00 mm long and has a weight of w = 160 N. Tweedledum applies an upward force of magnitude F1 = 60.0 NN at the left end of the board. Which of the following is the correct equation for Στ for the given rotation axis? All rotation axes lie on the x-axis and torques that would cause a counterclockwise rotation are positive. Enter the letter(s) of the correct equation(s) in alphabetical order. For instance, if you thought that choices A, B, and D were correct, you would enter ABD. Answer Choices: Axis of Rotation Et A x=0 (1/2)wL+F2d=0 B x=L (1/2)wL-F2(L-d)-F1L=0 C x=0 (-1/2)wL+F2d=0 D x=d -F1d-F2(d-(1/2)L)=0 E x=(1/2)L (-1/2)F1L+F2(d-(1/2)L) F x=(1/2)L (1/2)F1L+F2(d-(1/2)L)arrow_forwardA man is attempting to raise a 7.5-m-long, 28 kg flagpole that has a hinge at the base by pulling on a rope attached to the top of the pole, as shown. With what force does the man have to pull on the rope to hold the pole motionless in this position?arrow_forward
- Hi please help: A force (F= 5.0 N) is exerted on the right end of a horizontal beam with a length L= 4.0 m as shown. What is the magnitude of the torque around point P due to the force? Answer in three significant figuresarrow_forwardWhen tightening a bolt, you push perpendicularly on a wrench with a force of 165 N at a distance of 0.140 m from the center of the bolt. How much torque are you exerting relative to the center of the bolt?arrow_forwardA 75 kg man's arm, including the hand, can be modeled as a 79-cm-long uniform cylinder with a mass of 3.7 kg. In raising both his arms, from hanging down to straight up, by how much does he raise his center of gravity?arrow_forward
- Principles of Physics: A Calculus-Based TextPhysicsISBN:9781133104261Author:Raymond A. Serway, John W. JewettPublisher:Cengage LearningUniversity Physics Volume 1PhysicsISBN:9781938168277Author:William Moebs, Samuel J. Ling, Jeff SannyPublisher:OpenStax - Rice UniversityGlencoe Physics: Principles and Problems, Student...PhysicsISBN:9780078807213Author:Paul W. ZitzewitzPublisher:Glencoe/McGraw-Hill