Fluid Mechanics 8e In Si Units
8th Edition
ISBN: 9789814720175
Author: Frank M. White
Publisher: McGraw-Hill Education
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 11, Problem 11.34P
You are asked to consider a pump geometrically similar to the 9-in-diameter Taco pump of Fig. Pl 1.34 to deliver 1200 gal/min at 1500 r/min. Determine the appropriate (a) impeller diameter, (b) BEP horsepower, (c) shutoff head, and (d) maximum efficiency. The fluid is kerosene, not water.
Expert Solution & Answer
Trending nowThis is a popular solution!
Students have asked these similar questions
You wish to water your garden with 100 ft of 5/8-in-diameterhose whose roughness is 0.011 in. What will be the delivery,in ft3/s, if the gage pressure at the faucet is 60 lbf/in2?If there is no nozzle (just an open hose exit), what is thethe maximum horizontal distance the exit jet will carry?
A centrifugal pump with 30 cm diameter impeller is rated at 30 lps against a head of 24 m when rotating at 1750 rpm. What would be the rating of a pump of identical geometric shape with a 15 cm diameter impeller? Assume pump efficiencies and rotative speeds are identical.
Pump specific speed and turbine specific speed are “extra” parameters that are not necessary in the scaling laws for pumps and turbines. Explain, then, their purpose.
Chapter 11 Solutions
Fluid Mechanics 8e In Si Units
Ch. 11 - Prob. 11.1PCh. 11 - Prob. 11.2PCh. 11 - Prob. 11.3PCh. 11 - Prob. 11.4PCh. 11 - Pl 1.5 What type of pump is shown in Fig. Pl 1.5?...Ch. 11 - Prob. 11.6PCh. 11 - A piston PDP has a 5-in diameter and a 2-in stroke...Ch. 11 - Pl 1.8 A Bell and Gossett pump at best efficiency,...Ch. 11 - Prob. 11.9PCh. 11 - Prob. 11.10P
Ch. 11 - Prob. 11.11PCh. 11 - Prob. 11.12PCh. 11 - Pl 1.13 A 3.5 hp pump delivers 1140 lbf of...Ch. 11 - Prob. 11.14PCh. 11 - Prob. 11.15PCh. 11 - Prob. 11.16PCh. 11 - Prob. 11.17PCh. 11 - Prob. 11.18PCh. 11 - Pl 1.19 A centrifugal pump has r2 = 9 in, b2 = 2...Ch. 11 - Prob. 11.20PCh. 11 - Prob. 11.21PCh. 11 - Prob. 11.22PCh. 11 - P11.23 When pumping water, (a) at what speed...Ch. 11 - Prob. 11.24PCh. 11 - Prob. 11.25PCh. 11 - Prob. 11.26PCh. 11 - Prob. 11.27PCh. 11 - Prob. 11.28PCh. 11 - Tests by the Byron Jackson Co. of a...Ch. 11 - A pump, geometrically similar to the 12.95-in...Ch. 11 - Prob. 11.31PCh. 11 - Prob. 11.32PCh. 11 - Prob. 11.33PCh. 11 - You are asked to consider a pump geometrically...Ch. 11 - Prob. 11.35PCh. 11 - Prob. 11.36PCh. 11 - Prob. 11.37PCh. 11 - Prob. 11.38PCh. 11 - Prob. 11.39PCh. 11 - Prob. 11.40PCh. 11 - Prob. 11.41PCh. 11 - Prob. 11.42PCh. 11 - The 28-in-diameter pump in Fig. 11.7a at 1170...Ch. 11 - Prob. 11.44PCh. 11 - Prob. 11.45PCh. 11 - Prob. 11.46PCh. 11 - PI 1.47 A pump must be designed to deliver 6 m /s...Ch. 11 - Pl 1.48 Using the data for the pump in Prob. Pl...Ch. 11 - Prob. 11.49PCh. 11 - Prob. 11.50PCh. 11 - Prob. 11.51PCh. 11 - Prob. 11.52PCh. 11 - Prob. 11.53PCh. 11 - Prob. 11.54PCh. 11 - Prob. 11.55PCh. 11 - Prob. 11.56PCh. 11 - Prob. 11.57PCh. 11 - Prob. 11.58PCh. 11 - Suppose it is desired to deliver 700 ftVmin of...Ch. 11 - Prob. 11.60PCh. 11 - Prob. 11.61PCh. 11 - Prob. 11.62PCh. 11 - Pl 1.63 A good curve-fit to the head vs. flow for...Ch. 11 - Prob. 11.64PCh. 11 - *P11.65 An 11.5-in-diameter centrifugal pump,...Ch. 11 - Pl 1.66 It is proposed to run the pump of Prob. Pl...Ch. 11 - Prob. 11.67PCh. 11 - Prob. 11.68PCh. 11 - The pump of Prob. P1138, running at 3500 r/min, is...Ch. 11 - Prob. 11.70PCh. 11 - Prob. 11.71PCh. 11 - Prob. 11.72PCh. 11 - Prob. 11.73PCh. 11 - Prob. 11.74PCh. 11 - Prob. 11.75PCh. 11 - Prob. 11.76PCh. 11 - Prob. 11.77PCh. 11 - Prob. 11.78PCh. 11 - Prob. 11.79PCh. 11 - Determine if either (a) the smallest or (b) the...Ch. 11 - Prob. 11.81PCh. 11 - Prob. 11.82PCh. 11 - Prob. 11.83PCh. 11 - Prob. 11.84PCh. 11 - Prob. 11.85PCh. 11 - Prob. 11.86PCh. 11 - Prob. 11.87PCh. 11 - Prob. 11.88PCh. 11 - A Pelton wheel of 12-ft pitch diameter operates...Ch. 11 - Prob. 11.90PCh. 11 - Prob. 11.91PCh. 11 - Prob. 11.92PCh. 11 - Prob. 11.93PCh. 11 - Prob. 11.94PCh. 11 - Prob. 11.95PCh. 11 - Prob. 11.96PCh. 11 - Prob. 11.97PCh. 11 - Prob. 11.98PCh. 11 - Prob. 11.99PCh. 11 - Prob. 11.100PCh. 11 - Prob. 11.101PCh. 11 - Prob. 11.102PCh. 11 - Prob. 11.103PCh. 11 - Prob. 11.104PCh. 11 - Prob. 11.105PCh. 11 - Prob. 11.106PCh. 11 - Prob. 11.107PCh. 11 - Prob. 11.108PCh. 11 - Prob. 11.1WPCh. 11 - Prob. 11.2WPCh. 11 - Prob. 11.3WPCh. 11 - Prob. 11.4WPCh. 11 - Prob. 11.5WPCh. 11 - Consider a dimensionless pump performance chart...Ch. 11 - Prob. 11.7WPCh. 11 - Prob. 11.8WPCh. 11 - Prob. 11.9WPCh. 11 - Prob. 11.10WPCh. 11 - Prob. 11.1CPCh. 11 - Prob. 11.2CPCh. 11 - Prob. 11.3CPCh. 11 - Prob. 11.4CPCh. 11 - Prob. 11.5CPCh. 11 - Prob. 11.6CPCh. 11 - Prob. 11.7CPCh. 11 - Prob. 11.8CPCh. 11 - Prob. 11.1DP
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.arrow_forwardLarge hydroturbines achieve overall efficiencies above 95%, while the best efficiency of large pumps is a little more than 90%. Discuss some reasons for this to happen.arrow_forwardA typical pump has a head that, for a given shaft rotationrate, varies with the fl ow rate, resulting in a pump performancecurve as in Fig. P3.181. Suppose that this pump is75 percent efficient and is used for the system in Prob.3.180. Estimate ( a ) the flow rate, in gal/min, and ( b ) thehorsepower needed to drive the pump.arrow_forward
- Discuss which dimensionless pump performance parameter is typically used as the independent parameter. Repeat for turbines instead of pumps. Explain.arrow_forwardThe large reservoir in the following figure provides water for the indicated tank with a flow rate of 10 L/s. Check that the machine is installed and a pump or a turbine, and determine its power, if the yield is 75%. Suppose ideal fluid. Data: γH20 = 104N/m3 ; ATubes = 10mc2 ; g = 10m/s2 .arrow_forwardThe dimensions of a Francis radial-flow hydroturbine are r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m, where location 2 is the inlet and location 1 is the outlet. At the turbine inlet and outflow, the runner blade angles are β2 = 71.4° and β1 = 15.3°, respectively. The runner rotates at a rate of ń = 160 rpm. At design conditions, the volume flow rate is 80.0 m3 /s. (a) State the necessary assumptions and calculate the angle α2 at which the wicket gates should turn the flow (Figure Q1), with α2 measured from the radial direction at the runner inlet. (b) Calculate the swirl angle α1 (Figure Q1), where α1 is the angle measured from the radial direction at the runner output. (c) Calculate the needed net head and power output. (d) Discuss the actual power output and head required for actual case of the turbine (irreversibility not neglected). (Properties For water at 20oC, ρ = 998.0 kg/m3)arrow_forward
- An 8-in model pump delivering 180°F water at 800 gal/minand 2400 r/min begins to cavitate when the inlet pressureand velocity are 12 lbf/in2 absolute and 20 ft/s, respectively.Find the required NPSH of a prototype that is4 times larger and runs at 1000 r/min.arrow_forwardAn aqueduct is required to supply water to the community.Data: Families = 12 Average members per family = 3 people Breakfast, lunch and dinner = 15 total liters / family Showers = 10lt / person, one daily shower Kitchen wash = 13lts / day Total distance of the pipeline to the storage tank = 1200 meters Total height H from the pump point to delivery to the tank = 70 meters Determine: Estimation of the total volume of the recommended tank, an autonomy of at leas 2 days of storage. It is required to propose a pump that allows at least filling the tank between 5 to 12 hours operation, it must include details of the pump, as well as its curve Image: schematic detail of the proposed systemarrow_forwardWater falls vertically downward from an open faucet with an initial velocity of 66 cm/s. If the stream diameter at the faucet head is 0.5 cm what is the stream diameter at a distance 5 cm below the faucet exit?arrow_forward
- A pump, geometrically similar to the 12.95-in model in Fig. P11.24,has a diameter of 24 in and is to develop 30 hp at BEP when pumping gasoline (not water).Determine (a) the appropriate speed, in r/min; (b) the BEP head, in ft; and (c) the BEP flowrate, in gal/min.arrow_forwardA certain axial flow turbine has an output torque M that isproportional to the volume flow rate Q and also depends onthe density ρ , rotor diameter D , and rotation rate Ω . Howdoes the torque change due to a doubling of ( a ) D and ( b ) Ω ?arrow_forwardA river of width b and depth h 1 passes over a submergedobstacle, or “drowned weir,” in Fig. P3.80, emerging at anew fl ow condition ( V 2 , h 2 ). Neglect atmospheric pressure,and assume that the water pressure is hydrostatic at bothsections 1 and 2. Derive an expression for the force exertedby the river on the obstacle in terms of V 1 , h 1 , h 2 , b , ρ , andg . Neglect water friction on the river bottom.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University Press
Mechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSON
Thermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEY
Mechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage Learning
Engineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
8.01x - Lect 27 - Fluid Mechanics, Hydrostatics, Pascal's Principle, Atmosph. Pressure; Author: Lectures by Walter Lewin. They will make you ♥ Physics.;https://www.youtube.com/watch?v=O_HQklhIlwQ;License: Standard YouTube License, CC-BY
Dynamics of Fluid Flow - Introduction; Author: Tutorials Point (India) Ltd.;https://www.youtube.com/watch?v=djx9jlkYAt4;License: Standard Youtube License