null Edition

ISBN: 9781323905210

Author: Limbrunner

Publisher: PEARSON C

Concept explainers

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial…

Videos

Textbook Question

Chapter 11, Problem 11.44SP

A 1 -in.-diameter ASTM A36 steel tie rod, 3 0 ft long, is used to tie together two walls of a building. The rod is tensioned to 1 0 , 000 lb. Compute the tensile stress in the rod if the temperature rises by 3 0 degrees and if it falls by 5 0 degrees. Assume that the walls do not move.

Expert Solution & Answer

Want to see the full answer?

Check out a sample textbook solution

See solution

Chapter 11, Problem 11.43SP

Chapter 11, Problem 11.45SP

Students have asked these similar questions

A brass pipe has an internal diameter of 400mm and a metal thickness of 6mm and.A single layer of high tensile wire of diameter 3mm is wound closely around it at a tension of 500N find the stress in the pipe when there is no internal pressure.

Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model

A tube from aluminium with an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what is the maximum force (in kN) that the member can support.

Chapter 11 Solutions

APPLIED STATICS & STRENGTH OF MATERIALS

Ch. 11 - Prob. 11.1P Ch. 11 - A rectangular ASTM A36 steel bar 2 in. by 6 in. in...Ch. 11 - Calculate Poisson’s ratio for a cast iron that has...Ch. 11 - Modulus of elasticity, modulus of rigidity, and...Ch. 11 - Compute all the dimensional changes for the steel...Ch. 11 - A surveyor’s steel tape is exactly 100ft long...Ch. 11 - An aluminum wire is stretched between two rigid...Ch. 11 - Prob. 11.8P Ch. 11 - A concrete roadway pavement is placed in 60ftlong...Ch. 11 - Prob. 11.10P

Ch. 11 - A 4in. -by- 8in . short wood post is reinforced on...Ch. 11 - A short post. 150mm by 150mm , of Douglas fir, is...Ch. 11 - The cables of a power line are copper-coated steel...Ch. 11 - Prob. 11.14P Ch. 11 - For the short column shown, assuming that lateral...Ch. 11 - A 1.0 -in.-diameter hole is drilled on the...Ch. 11 - Prob. 11.17P Ch. 11 - A long, flat steel bar 4 in. wide and 38 thick is...Ch. 11 - A long, flat steel bar 5 in. wide and 38 thick has...Ch. 11 - 11.20 An aluminum specimen of circular cross...Ch. 11 - Prob. 11.21P Ch. 11 - Prob. 11.22P Ch. 11 - 11.23 A concrete cylinder, -in, in diameter, was...Ch. 11 - Prob. 11.24P Ch. 11 - For the element of Problem 11.24: a. Locate the...Ch. 11 - Prob. 11.26CP Ch. 11 - Prob. 11.27CP Ch. 11 - Prob. 11.28CP Ch. 11 - Prob. 11.29CP Ch. 11 - A 50 -mm-diameter ASTM A36 steel rod is subjected...Ch. 11 - A 4 -ft-long square ASTM A36 steel bar, 2 in. by 2...Ch. 11 - A concrete test cylinder is 150 mm in diameter and...Ch. 11 - A 14 -in.-long steel rod, 112 in diameter, was...Ch. 11 - Determine the change in the diameter of an ASTM...Ch. 11 - 11.35 The steel bar shown in Figure 11.3 (see...Ch. 11 - Compute the change in the thickness of the ASTM...Ch. 11 - The steel rails of a railroad track are laid in...Ch. 11 - A rolled brass rod and a steel rod are secured to...Ch. 11 - 11.39 A -m-long steel member is set snugly between...Ch. 11 - 11.40 The distance between two fixed points on a...Ch. 11 - A steel truss is loaded as shown. The...Ch. 11 - 11.42 For the truss of Problem 5.25, the members...Ch. 11 - A surveyor’s steel tape has a cross-sectional area...Ch. 11 - A 1 -in.-diameter ASTM A36 steel tie rod, 30 ft...Ch. 11 - 11.45 A copper wire is held taut between two...Ch. 11 - 11.46 A horizontal steel member is anchored at...Ch. 11 - 11.47 Three vertical steel wires are loaded as...Ch. 11 - 11.48 Assume for Problem 11.47 that the same load...Ch. 11 - The rod shown is firmly attached to rigid...Ch. 11 - 11.50 A structural steel bar mm in width and mm...Ch. 11 - A redwood timber member having a 16 -in.-square...Ch. 11 - A steel pipe has an outside diameter of 12 in. and...Ch. 11 - A short 14 -in.-square concrete pier is reinforced...Ch. 11 - An ASTM A36 steel rod, 375.06 mm long and having a...Ch. 11 - An aluminum rod with an area of 1.5in.2 and an...Ch. 11 - A solid brass cylinder with a cross-sectional area...Ch. 11 - Three 14 in.-diameter wires are symmetrically...Ch. 11 - Rework Problem 11.57 with outer wires of aluminum,...Ch. 11 - Three rods support a weight, as shown. The...Ch. 11 - A flat steel bar 4 in. wide and 12 thick must be...Ch. 11 - A 19 -mm-diameter hole is drilled on the...Ch. 11 - A flat bar is 38 thick and has a centrally located...Ch. 11 - A long, flat steel bar 125 mm wide and 10 mm thick...Ch. 11 - 11.64 A short -in.-diameter compression member is...Ch. 11 - Prob. 11.65SP Ch. 11 - 11.66 A rectangular block of wood, in. by in. in...Ch. 11 - 11.67 A -mm-diameter rod is subjected to an axial...Ch. 11 - The rectangular plate shown is subjected to a...Ch. 11 - A wood block, subjected to a tensile load, fails...Ch. 11 - Prob. 11.70SP Ch. 11 - A shaft in a speed-reduction mechanism is loaded...Ch. 11 - An axially loaded 50 -mm-by- 75 -mm steel bar has...

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.