APPLIED STATICS & STRENGTH OF MATERIALS
null Edition
ISBN: 9781323905210
Author: Limbrunner
Publisher: PEARSON C
expand_more
expand_more
format_list_bulleted
Textbook Question
Chapter 11, Problem 11.51SP
A redwood timber member having a
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
A steel bar carrying 3000kN load,F, is attached to a support by a round pin 0.3m in diameter. Calculate the shearstress in the pin,MPa. If the diameter doubled, calculate the shear stress in the pin,MPa.
In a cruise ship, a liferaft is hanged by suspending it with a thick metallic cable attached to both ends which passes over a pulley anchored to the deck. A tensile force of 4 kN is carried for each side of the cable. The cable and the pulley are located in a vertical plant shown below. The pulley is free to rotate about the horizontal circular axle. Calculate the diameter of the axle if the allowable transverse shearing stress is only 50 x 106 Pa.
There is a tube from aluminium, which has an outside diameter of 50 (mm) and a wall thickness of 5 (mm) is used as a compression member. If the axial normal stress in the member must be limited to 90 MPa, what can the maximum force (in kN) that the member can support?
Chapter 11 Solutions
APPLIED STATICS & STRENGTH OF MATERIALS
Ch. 11 - Prob. 11.1PCh. 11 - A rectangular ASTM A36 steel bar 2 in. by 6 in. in...Ch. 11 - Calculate Poisson’s ratio for a cast iron that has...Ch. 11 - Modulus of elasticity, modulus of rigidity, and...Ch. 11 - Compute all the dimensional changes for the steel...Ch. 11 - A surveyor’s steel tape is exactly 100ft long...Ch. 11 - An aluminum wire is stretched between two rigid...Ch. 11 - Prob. 11.8PCh. 11 - A concrete roadway pavement is placed in 60ftlong...Ch. 11 - Prob. 11.10P
Ch. 11 - A 4in. -by- 8in . short wood post is reinforced on...Ch. 11 - A short post. 150mm by 150mm , of Douglas fir, is...Ch. 11 - The cables of a power line are copper-coated steel...Ch. 11 - Prob. 11.14PCh. 11 - For the short column shown, assuming that lateral...Ch. 11 - A 1.0 -in.-diameter hole is drilled on the...Ch. 11 - Prob. 11.17PCh. 11 - A long, flat steel bar 4 in. wide and 38 thick is...Ch. 11 - A long, flat steel bar 5 in. wide and 38 thick has...Ch. 11 - 11.20 An aluminum specimen of circular cross...Ch. 11 - Prob. 11.21PCh. 11 - Prob. 11.22PCh. 11 - 11.23 A concrete cylinder, -in, in diameter, was...Ch. 11 - Prob. 11.24PCh. 11 - For the element of Problem 11.24: a. Locate the...Ch. 11 - Prob. 11.26CPCh. 11 - Prob. 11.27CPCh. 11 - Prob. 11.28CPCh. 11 - Prob. 11.29CPCh. 11 - A 50 -mm-diameter ASTM A36 steel rod is subjected...Ch. 11 - A 4 -ft-long square ASTM A36 steel bar, 2 in. by 2...Ch. 11 - A concrete test cylinder is 150 mm in diameter and...Ch. 11 - A 14 -in.-long steel rod, 112 in diameter, was...Ch. 11 - Determine the change in the diameter of an ASTM...Ch. 11 - 11.35 The steel bar shown in Figure 11.3 (see...Ch. 11 - Compute the change in the thickness of the ASTM...Ch. 11 - The steel rails of a railroad track are laid in...Ch. 11 - A rolled brass rod and a steel rod are secured to...Ch. 11 - 11.39 A -m-long steel member is set snugly between...Ch. 11 - 11.40 The distance between two fixed points on a...Ch. 11 - A steel truss is loaded as shown. The...Ch. 11 - 11.42 For the truss of Problem 5.25, the members...Ch. 11 - A surveyor’s steel tape has a cross-sectional area...Ch. 11 - A 1 -in.-diameter ASTM A36 steel tie rod, 30 ft...Ch. 11 - 11.45 A copper wire is held taut between two...Ch. 11 - 11.46 A horizontal steel member is anchored at...Ch. 11 - 11.47 Three vertical steel wires are loaded as...Ch. 11 - 11.48 Assume for Problem 11.47 that the same load...Ch. 11 - The rod shown is firmly attached to rigid...Ch. 11 - 11.50 A structural steel bar mm in width and mm...Ch. 11 - A redwood timber member having a 16 -in.-square...Ch. 11 - A steel pipe has an outside diameter of 12 in. and...Ch. 11 - A short 14 -in.-square concrete pier is reinforced...Ch. 11 - An ASTM A36 steel rod, 375.06 mm long and having a...Ch. 11 - An aluminum rod with an area of 1.5in.2 and an...Ch. 11 - A solid brass cylinder with a cross-sectional area...Ch. 11 - Three 14 in.-diameter wires are symmetrically...Ch. 11 - Rework Problem 11.57 with outer wires of aluminum,...Ch. 11 - Three rods support a weight, as shown. The...Ch. 11 - A flat steel bar 4 in. wide and 12 thick must be...Ch. 11 - A 19 -mm-diameter hole is drilled on the...Ch. 11 - A flat bar is 38 thick and has a centrally located...Ch. 11 - A long, flat steel bar 125 mm wide and 10 mm thick...Ch. 11 - 11.64 A short -in.-diameter compression member is...Ch. 11 - Prob. 11.65SPCh. 11 - 11.66 A rectangular block of wood, in. by in. in...Ch. 11 - 11.67 A -mm-diameter rod is subjected to an axial...Ch. 11 - The rectangular plate shown is subjected to a...Ch. 11 - A wood block, subjected to a tensile load, fails...Ch. 11 - Prob. 11.70SPCh. 11 - A shaft in a speed-reduction mechanism is loaded...Ch. 11 - An axially loaded 50 -mm-by- 75 -mm steel bar has...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- A link in an automated packaging machine is a hollow tube made from 6061-T6 aluminum. Its dimensions are as follows: outside diameter = 32.0 mm, inside diameter = 28.0 mm, and length = 1.00 m. Compute the tensile force required to produce an elongation of the bar of 1.3 mm. Would the stress produced by the force just found be safe if the load is applied repeatedly?arrow_forwardWhat wall thickness in mm is required for a 634 mm diameter cylinder under an internal pressure of 18 MPa? Use a design stress of 80 MPa?arrow_forwardPROBLEM 2A tri metallic bar is uniformly compressed by an axial force P=12kN applied through a rigid end plate. The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter 10mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm. E for steel =210Gpa, E for brass =100GPa and E for copper is 120GPa. Calculate the compressive stress of each metal due to force P.arrow_forward
- A short timber post of Douglas fir is subjected to an axial compressive load of 40,000 lb. The nominal dimensions of the post area are 10 in. by 10 in. Its length is 8 ft. Assume a proportional limit of 6000 psi. Using dressed dimensions, compute (a) stress. (Unit: psi) A short timber post of Douglas fir is subjected to an axial compressive load of 40,000 lb. The nominal dimensions of the post area are 10 in. by 10 in. Its length is 8 ft. Assume a proportional limit of 6000 psi. Using dressed dimensions, compute (b) strain. A short timber post of Douglas fir is subjected to an axial compressive load of 40,000 lb. The nominal dimensions of the post area are 10 in. by 10 in. Its length is 8 ft. Assume a proportional limit of 6000 psi. Using dressed dimensions, compute (c) total deformation. (Unit: in)arrow_forwardA 12” X 16”simply supported pine wood beam is being considered to carry a uniform load distribution across a span of 12’ as shown. In addition to the uniform load, the beam is also subjected to a tensile load of 20 kips. If the ultimate tensile stress in pine wood is 4500 psi, determine whether the beam is considered safe according to the Allowable Stress Method, using a Factor of Safety 2.5. Hint: you can calculate the maximum tensile stress in the cross-section without having to use Mohr’s circlearrow_forwardThe global stresses in a three-ply laminate are given at the top and bottom surface of each ply in the tables below. Assume that each ply is 0.005 in. thick and the laminate has a top cross section of 4 in. × 4 in. What is the resultant force component Nx for the laminate in lb/in? What is the resultant force component Ny for the laminate in lb/in? What is the resultant force component Nxy for the laminate in lb/in?arrow_forward
- A cantilever beam, 80 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1100 N/m at the wall. Compute the magnitude of the maximum flexural stress. Answer must be in MPa.arrow_forwardglulam beam is loaded by uniformly distributed load pch at one end by point load. The beam has a rectangular cross-section with dimensions 115\times 270 mm^2 and is braced in a rigid direction a. calculate the maximum normal stress in the beam and indicate where it goes. sketch the normal stress distribution across the door section b. calculate the maximum shear stress in the beam, indicate where it goes sketch the shear stress distributionarrow_forwardThe cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.arrow_forward
- A cast iron beam is of T-section as shown in Fig. The beam is simply supported on a span of 6 m. The beam carries a uniformly distributed load of 2 kN/m length on the entire span. Determine the maximum tensile and maximum compressive stresses.arrow_forwardThe bar in the figure below is made from standard acrylic plastic (E = 2960 MPa). Compute the total change in length, δof the shaft due to the loadings shown.arrow_forwardA flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
Mechanics of Materials Lecture: Beam Design; Author: UWMC Engineering;https://www.youtube.com/watch?v=-wVs5pvQPm4;License: Standard Youtube License