Interpretation:
The phase diagram for krypton should be sketched. Whether krypton can be liquefied as room temperature or not should be determined.
Concept introduction:
Phase diagram is a graph that represents the solid phase, liquidphase, and gaseous phase of one substance or mixture of substance under different conditions of temperature and pressure.
The temperature and pressure on a phase diagram at which gas, liquid, and solid phases coexistis called triple point. The temperature and pressure in the phase diagram at which substance is lies between liquid-gas phases is called critical point.The temperature and pressure at which liquid or gas is neither a true liquid nor a true gas is called supercritical point.
The conversion factor to convert Kelvin to
The conversion factor to convert
The conversion of a gas into a liquid state by change in temperature, pressure, and volume is termed as liquefication of gas. The highest temperatureat which gas changes into liquid is termed as critical temperature. The minimum pressure that liquefies gas at its critical temperature is termed as critical pressure.
Want to see the full answer?
Check out a sample textbook solutionChapter 11 Solutions
CHEMISTRY-W/MASTERING CHEMISTRY ACCESS
- The vapor pressure of ethanol, C2H5OH, at 50.0 C is 233 mmHg, and its normal boiling point at 1 atm is 78.3 C. Calculate the vapH of ethanol.arrow_forwardConsider two different organic compounds, each with the formula C2H6O. One of these compounds is a liquid at room conditions and the other is a gas. Write Lewis structures consistent with this observation, and explain your answer. (Hint: The oxygen atom in both structures satisfies the octet rule with two bonds and two lone pairs.)arrow_forwardReferring to Figure 9.7, state what phase(s) is (are) present at (a) 1 atm, 10C. (b) 3 mm Hg, 20C. (c) 1000 mm Hg, 75C.arrow_forward
- Consider the phase diagram and heating-curve graphs for Question 113. Draw corresponding heating curves for T1 to T2 at pressures P1 and P2. Label each phase and phase change on your heating curves.arrow_forwardA 22.5-g sample of ice at 0.0 oC is added to 100.0 g of warm water at 35.0 oC, and the final temperature of the mixture is 14.0 oC. (a)How much heat(in Joules)is lost by the warm water? (b) How much heat (in Joules) is absorbed by the melted ice when its temperature increases from 0.0 oC to 14.0 oC? (c) How much heat is absorbed by ice during melting at 0.0 oC? (d) What is the enthalpy of fusion of ice in kJ/mol? (Specific heat of water = 4.184 J/(g.oC)arrow_forwardHow much energy would be needed to freeze a 75.37-g sample of gallium at its freezing point of 29.7646 °C? Atomic Mass of Ga: 69.72 g/mol. Use the needed thermodynamic data from the given below: Heat of Fusion: 5.59 kJ/mol Heat of Vaporization: 256 kJ/mol A -6.04 kJ В 6.04 kJ (c) 276.75 kJ D -276.75 kJarrow_forward
- At 25 °C gallium is a solid with a density of 5.91 g/cm^3. Its melting point, 29.8 °C, is low enough that you can melt it by holding it in your hand. The density of liquid gallium just above the melting point is 6.1 g/cm3. Based on this information, what unusual feature would you expect to find in the phase diagram of gallium?arrow_forwardDetermine the vapor pressure (in mm Hg) of a substance at 29°C, whose normal boiling point is 76°C and has a Delta Hvap of 38.7 kJ/mol.arrow_forward7. Calculate the amount of energy needed to convert 200. g of water at 25.0°C to steam at 150.0°C. The following information will be useful:• The heat of vaporization of water is 2256 J·g–1• The specific heat capacity of water is 4.184 J·g–1·K–1• The specific heat capacity of water vapour is 1.86 J·g–1·K–18. In the sulfur tetrafluoride (SF4) molecule, all four F atoms are bonded to the central S atom. The following question set concerns this molecule.a) Draw the Lewis structure for sulfur tetrafluoride (SF4). b) Which electron pair geometry does the SF4 molecule belong to? c) Which single word best describes the molecular geometry or shape of the SF4 molecule?arrow_forward
- Determine the vapor pressure (in mm Hg) of a substance at 29°C, whose normal boiling point is 76°C and has a ΔHvap of 38.7 kJ/mol.arrow_forwardPhase changes occur between different solid forms, as well as from solid to liquid, liquid to gas, and solid to gas. When white tin at 1.00 atm is cooled below 13.2°C, it spontaneously changes (over a period of weeks) to gray tin. The density of gray tin is less than the density of white tin ( 5.75 g cm^-3 vs 7.31 g cm^-3 ). Some white tin is compressed to a pressure of 2.00 atm. At this pressure, should the temperature be higher or lower than 13.2°C for the conversion to gray tin to occur? Explain your reasoning.arrow_forward
- Chemistry: The Molecular ScienceChemistryISBN:9781285199047Author:John W. Moore, Conrad L. StanitskiPublisher:Cengage LearningGeneral Chemistry - Standalone book (MindTap Cour...ChemistryISBN:9781305580343Author:Steven D. Gammon, Ebbing, Darrell Ebbing, Steven D., Darrell; Gammon, Darrell Ebbing; Steven D. Gammon, Darrell D.; Gammon, Ebbing; Steven D. Gammon; DarrellPublisher:Cengage LearningChemistry: Principles and PracticeChemistryISBN:9780534420123Author:Daniel L. Reger, Scott R. Goode, David W. Ball, Edward MercerPublisher:Cengage Learning
- Chemistry: An Atoms First ApproachChemistryISBN:9781305079243Author:Steven S. Zumdahl, Susan A. ZumdahlPublisher:Cengage LearningChemistryChemistryISBN:9781305957404Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCostePublisher:Cengage Learning